Getting Started - Philips 6917348PH User Manual

EN Instruction for Use
Thank you for buying the Philips LivingColors wall
lamp!
LivingColors has been especially designed to create
your own ambience at home, through colour and light.
When using LivingColors for the first time, please
read these instructions carefully and save them for
future reference. By following our guidelines, you will
enjoy the full functionality of Philips LivingColors.
Register your product at www.philips.com/welcome
to stay up to date about new Philips LivingAmbiance
products
This manual will help you to...
1. Get started
2. Create your own ambience with LivingColors
3. Connect LivingColors to other Philips
LivingAmbiance products
4. Answer frequently asked questions
5. Get additional support
Important:
- The manufacturer advises the correct use
of luminaires! Therefore always follow these
instructions to ensure correct and safe
installation and functioning of the luminaire and
keep them for future reference.
- The Luminaire is only suitable for wiring directly
into the mains.
- The Luminaire is only suitable for mounting on
the wall.
- If in doubt, consult a qualified electrician or
contact your retail outlet. Ensure that you always
install the luminaire to the relevant regulations.
Certain regulations indicate that luminaires
should be installed by a qualified electrician (e.g.
Part P for the UK).
- Always tighten the terminal screws firmly.
- The luminaire is suitable for mounting on normal
flammable surfaces.
- Please mount the luminaire out of children's
reach.
- If the luminaire is mounted on a metallic surface,
this surface must be bonded to the protective
earth conductor or to the equipotential bonding
conductor of the installation.
- Ensure that you don't drill through electrical
wires or any other obstruction in the wall or
ceiling during installation.
- If the luminaire is mounted on a ceiling-box or
wall-box, the box must be covered with a lid first
(e.g. The Netherlands).
- Electrical wiring must never be clamped or
twisted between the luminaire and the mounting
surface.
- Always consider all the technical specifications of
the luminaire. Verify the information on the label
of the luminaire and in this manual.

1. Getting started:

- Always isolate the Power before commencing
installation, maintenance or repair.
- Strip the wires as indicated in the diagram.
- If you have a connection box for wall lamps
on your wall, connect the wall lamp directly by
screwing its plate to the connection
- If you don't have a connection box for wall lamps
on your wall, find the place where cables come
out of the wall. Drill two holes in the wall, put in
plastic plugs first and then screw the plate onto
the wall.
- Connect the earth cable (usually yellow with
black stripes) to the earth connection (identified
by the earth icon) inside the base of the luminaire.
- Observe the correct colour of the wiring during
installation: blue (N) and brown (L). Connect
these 2 wires accordingly from your power grid
to the terminal blocks inside the base of the
ceiling luminaire.
- Put the luminaire on the plate, which you screwed
to the wall earlier; fix it on both sides by screwing
in a screw.
- Insert the connection plug from the tripod into
the lamp – make sure you hear a click.
- Position the lamp on the tripod and direct
LivingColors towards the wall. You can adjust
the length of the luminaire by turning the ring in
the middle of the stand, pulling the top part of
the stand to the desired length, then turning the
ring back to fix the position. You can also pull the
luminaire to either side to find the best position.
- Open the battery compartment of the remote
control by sliding the button at the back. Insert 3
AAA batteries (+ and – as indicated).
2. Create your own ambience by
- Touching the desired colour on the colour
wheel. You can move your finger over the colour
wheel to refine the colour.
- Changing the colour saturation (adding more
white to the current colour). Press the saturation
up button for a deep colour or the saturation
down button for a more pastel colour. If you
keep pressing the saturation down button, you will
ultimately reach white.
- Dimming. Increase or decrease the light
intensity via the dimming buttons.
- Letting colours change automatically. Sweep
your finger around the colour wheel (one full
circle) and briefly press "I" ("On"); LivingColors
will switch to the automatic colour-changing
mode and the lamp will start changing colours
automatically.
19