Table of Contents
Advertisement
Use the unit's menu system to make various settings.
Among the menu setting items are some that can also be
set using dedicated buttons on the remote control.
Menu structure
The menu structure of the unit includes the following
items.
Menu
Item
Function set
number
01
Origin
Original key
02
EJECT
Eject block
03
A-CUE
Auto-cue level
04
Prog
Program
05
FADE
Fade in/out playback
06
RELAY
Relay playback
07
P onPL
Power on play
08
Mono
Mono output
09
RESUM
Resume
EOM (TRACK EOM) time
10
EOM
display
11
Inc-P
Incremental play
12
P-STEP
Pitch control steps
13
232C
Baud rate
14
S-BAC
Skip back
15
IR
Remote control reception
Silent interval between
16
INTVAL
tracks
17
FRAM
Frame time display
18
REMOT
Foot switch mode
19
FLASH
Flash start
Restore unit to factory
20
RESET
defaults
21
INFO
View the firmware version
User data settings (AES/
22
U-DATA
EBU, CD-500B only)
Set the parallel function
23
PARALL
(CD-500B only)
Menu operation basics
The basic procedures for making settings using the menu
system are as follows.
1 When the display shows the usual playback
information, activate the menu mode in which you
can select menu items by using the unit's front
panel buttons or the included TASCAM RC-500
remote control.
When using the front panel buttons:
•
(when the SHIFT indicator is lit), press the PITCH
[MENU] knob.
When using the remote control:
•
button.
Reference
2 Use the unit's front panel buttons or the remote
Page 27
Page 21
Page 24
Page 27
Page 29
Page 30
Page 26
Page 32
Page 24
Page 31
NOTE
Page 25
•
Page 27
Page 33
•
Page 29
Page 17
Page 31
Page 31
Page 32
Page 29
Page 33
3 Select the desired value.
Page 33
Page 34
Page 34
NOTE
•
•
In shift mode
Press the MENU
The center area of the display shows the menu item
selected. The menu item that was selected the last
time that the unit was in menu mode appears.
Menu item number Menu item name
control to conduct the following operation to select
the desired menu item.
When using the front panel buttons:
•
PITCH [MENU] knob or use the number buttons to
select the menu item, and press the PITCH [MENU]
knob to confirm.
When using the remote control:
•
and NEXT buttons, as well as the number buttons to
select the menu item, and press the ENTER button
to confirm.
The menu item number blinks before it has been
confirmed.
When using the number buttons input two digits
to select menu items. For example, to select menu
number
, press the 0 button followed by the 6
06
button.
The following step (3) applies to all items except
,
,
PROG
19 FLASH
20 RESET
their explanations for instructions about how to use
these items.
When using the front panel buttons:
•
PITCH [MENU] knob to select the value and press
the PITCH [MENU] knob to confirm the setting.
When using the remote control:
•
and NEXT buttons to select the value and press the
ENTER button to confirm the setting.
When a value different from the active setting is
selected, the value blinks. After the new setting is
confirmed, menu mode ends and the display shows
the usual playback information again.
To quit menu mode without changing a setting, press
the SHIFT button or DISPLAY [LOCK] button on the
front panel of the unit, or press the MENU button on
the remote control.
TASCAM CD-500/500B
4 – Menu
Setting
Turn the
Use the PREV
04
and
. See
21 INFO
Turn the
Use the PREV
19
Advertisement
Table of Contents
