(b) By disposing of electrical and electronic equipment user may be required to take adequate measures. correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment. TASCAM CD-6010...
Page 4
Safety Act of 1968, ” and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings. TASCAM CD-6010...
A-B repeat playback ..........26 Rear panel ................12 Intro check mode .............27 Display ...................13 Power on play function ...........27 Wireless remote control (TASCAM RC-500) .....14 Pitch control playback .............27 3 – Preparation ..........16 Setting the pitch adjustment increment ...28 Changing playback speed without changing Making connections ............16...
Page 6
9 – Error Messages ........37 10 – Specifications ........38 Media and formats ............38 Analog audio output ............38 Digital audio output ............38 Control input and output ..........38 Audio performance ............38 Backup memory ...............39 General .................39 Dimensional drawings ............39 For China CD-6010 TASCAM CD-6010...
Included items Auto-cue function can ready the unit to start playback • of a track from the moment sound starts Transport and pitch can be controlled using a TASCAM • The included items are listed below. RC-3F footswitch (sold separately)
Instructions that should be followed to avoid injury, damage to the unit or other equipment, and loss of data. Trademarks Connecting the power TASCAM is a trademark of TEAC Corporation, registered • in the U.S. and other countries. Insert the included power cord into the AC IN •...
Music discs with copy control, a copy-protection • system, have been released form several record companies in an attempt to protect the copyright. Since some of these discs do not comply with the CD specifications, they may not be playable on the unit. TASCAM CD-6010...
To turn the pitch function ON/OFF, press this button page 32.) when in shift mode (when the SHIFT indicator is lit) or When in menu mode, press this button to exit menu while pressing the SHIFT button. (See "Pitch control mode. playback" on page 27.) TASCAM CD-6010...
Page 11
REMOTE jack (2.5mm TRS) When paused, press this button to resume playback. Use this jack to connect a TASCAM RC-3F footswitch or TASCAM RC-20 direct playback remote control (sold During playback, press this button to return to the separately).
Press this button to cycle through the playback modes in the following order. (See "Playback modes" on page d Remote control receiver 23.) This receives signals from the included TASCAM RC-500 wireless remote control. Point the end of the remote Single Program...
When the original key function is on, KEY ORIG When in menu mode, the menu item is shown. When appears. (See “Changing the playback speed without menu items are shown, the letters appear as follows. changing the pitch (KEY ORIG)” on page 28.) TASCAM CD-6010...
2 – Names and Functions of Parts Wireless remote control (TASCAM RC-500) 6 MENU button Press this button to enter menu mode. When in menu mode, press this button to exit menu mode. (See “Menu operation basics” on page 19.)
Page 15
Press and hold when the program menu is open to clear the program. NOTE Unlike the CLEAR button on the main unit, the CLEAR button on the wireless remote control cannot be pressed and held while pressing a number button to delete a cue point. TASCAM CD-6010...
3 – Preparation Making connections The illustration below shows an example of connecting other equipment with a CD-6010. Precautions before making connections Before connecting other devices to the unit, read their manuals carefully. • Turn off the power (or put power into standby mode) for this unit and all equipment that will be connected to it.
The remote control reception setting (on/off) is saved • When to replace the batteries even if the unit’s power is turned off. Replace both batteries with new ones when the range of the remote control becomes short or if the buttons become unresponsive. TASCAM CD-6010...
NOTE Even when the panel lock function is enabled, the • unit can be controlled by a TASCAM RC-3F footswitch connected to the REMOTE jack on the front panel and external controllers connected to the RS-232C connector and CONTROL I/O PARALLEL connectors on the rear panel.
1 When the display shows the usual playback information, press the MENU button on the unit or the included TASCAM RC-500 remote control. The center area of the display shows the menu item selected. The menu item that was selected the last time that the unit was in menu mode appears.
Depending on the condition of a disc, this unit might not • be able to play it back, or skipping might occur. : Directory (Folder) : MP3/WAV le An example of data CD structure TASCAM CD-6010...
The OPEN/CLOSE button functions when the power is ON. • If you must remove a disc when the power is OFF, insert a paperclip or similar stiff rod into the hole beneath the tray and push to open the tray. TASCAM CD-6010...
If the auto-cue function is off, pause at the beginning • [PLAY] of the designated track. After this, press the Á PLAY button on the button on the unit or the Á remote to start playback. TASCAM CD-6010...
Press the + button to advance one frame, and press the − mode using the controls on the player or the included button to go back one frame. TASCAM RC-500 remote control. NOTE Using the front panel buttons: In jog mode, if you stop searching, playback will pause, but Press the PLAY MODE [REPEAT] button to cycle through the sound at the current position will be output continuously.
03 A-CUE When the resume function is on, appears in the RESUME lower part of the display. NOTE Options: (default value), The resume function on/off setting is retained even when the power is turned off. TASCAM CD-6010...
(See "Flash start function" on page 30.) Clearing cue points To clear a cue point, press the corresponding number button (indicator lit) while pressing the CLEAR button. After a cue point has been cleared the indicator will become unlit. TASCAM CD-6010...
SHIFT button. REPEAT button on the remote until Press the • REPEAT disappears from the top of the screen. NOTE The repeat playback setting is retained even when the power is turned off. TASCAM CD-6010...
After making the setting, press the SHIFT button and then the MENU [PITCH%] button to exit pitch setting mode. You can also exit pitch setting mode by pressing the MENU [PITCH%] button while pressing and holding the SHIFT button. TASCAM CD-6010...
To use program playback follows. to play tracks in the program order, set the playback mode to program playback mode and start playback. (See Track number Program number “Selecting the playback mode” on page 23.) TASCAM CD-6010...
1 Use the SEARCH Ô/ buttons to select the program number that you want to change. 2 Use the number buttons or SKIP Â/¯ buttons to select the desired track. 3 Press the SEARCH button to confirm the change. TASCAM CD-6010...
To set only the fade out time, in fade in/out setting mode • step 1 above, turn the TRACK SKIP/DATA knob on the player (or press the PREV or NEXT button on the remote) until OUT blinks. Then, press the TRACK SKIP/DATA knob TASCAM CD-6010...
Flash-loading cue points: ª Set cue points are loaded into memory. Multiple CD-6010 units can be used together and set NOTE so that when playback ends on one unit, playback can The flash start function is only possible with audio CDs.
TRACK TALLY" signal can be output from the CONTROL I/ O PARALLEL connector. With data CDs, an end of track warning will not appear on the display. The CONTROL I/O PARALLEL “21 EOM TRACK TALLY" signal will be output as a pulse when the file playback ends. TASCAM CD-6010...
The player can be set to wait for a specified time (interval time) after completing playback of one track before You can connect a TASCAM RC-3F footswitch (sold starting playback of the next track. separately) to the REMOTE jack on the front panel and...
The CONTROL I/O RS-232C connector (D-sub 9-pin, RS- 232C compliant) can be used for serial control of this unit You can connect a TASCAM RC-20 direct play remote (sold by a computer or other external device. separately) to the REMOTE jack on the front panel to use the unit's direct playback function.
-4dB 19 ATT attenuation is used or not (default value: Pin 1 NOTE STOP PARALLEL The attenuation setting is retained even when the power is turned off. Pin 8 START FADER START TASCAM CD-6010...
8 – Troubleshooting Please check the following items if the unit is not functioning properly. If you are still unable to resolve the problem please contact the retailer where you purchased the unit or TASCAM customer support. Power does not turn on CD cannot be played back ª...
9 – Error Messages When one of the following error messages appears, refer to the response below and resolve the cause. If you are still unable to resolve the problem please contact TASCAM customer support. Message Meaning Response Clean or change the disc.
Maximum Output level: +24 dBu (12.28 Vrms) 95 dB or more (1 kHz, JEITA) PHONES connector Connector: 6.3mm (1/4”) standard stereo jack Maximum output level: 45 mW + 45 mW or more (THD+N 0.1% or less, 32Ω load) TASCAM CD-6010...
Operating temperature range 5º–35° C Installation angle 15º or less Dimensional drawings Illustrations in this manual might differ from the actual product. • In order to improve the product, specifications and appearance could be changed without prior notice. • TASCAM CD-6010...
Page 40
CD-6010 TEAC CORPORATION tascam.jp Phone: +81-42-356-9143 1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan TEAC AMERICA, INC. tascam.com Phone: +1-323-726-0303 7733 Telegraph Road, Montebello, California 90640 USA TEAC CANADA LTD. tascam.com Phone: +1905-890-8008 Facsimile: +1905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.A.