Labels & Cosmetics - Grizzly G0814 Owner's Manual

403
WARNING!
INJURY HAZARD!
To reduce risk of short
and long-term injury,
wear safety glasses,
hearing protection, and
a respirator when using
this machine.
MODEL G0814
6 JOINTER w/CABINET STAND
"
Specifications
WARNING!
Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz
To reduce the risk of serious injury when using this machine:
Full-Load Amp Draw: 14A
1. Read & understand owner's manual before operating.
Cutterhead: 3-Knife, 2-1/2" Dia.
2. Always wear approved eye protection and respirator.
Knife Size: 6" x 1" x 1/8"
3. Only plug power cord into a grounded outlet.
Maximum Depth of Cut: 1/8"
4. Except when rabbeting, keep all guards in place and in proper
Maximum Rabbeting Depth: 1/2"
operating condition. Always replace guard after rabbeting.
Cutterhead Speed: 5000 RPM
5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
Cuts Per Minute: 15,000
6. Always use push blocks when face planing.
Fence Tilt: 45º, 90º, 135º
7. Never cut deeper than 1/8" on a single pass.
Table Size: 47" x 7-1/4" 8. Tie back long hair, roll up sleeves, and DO NOT wear loose
Weight: 245 lbs.
clothing, gloves, or jewelry.
9. Turn motor OFF and disconnect power before changing inserts,
adjusting tables/fence, or servicing.
10. Before starting, ensure tables are adjusted properly, blades are
secure, and jointer is stable.
11. Always support workpiece against fence and table. Never attempt
any operation free-handed.
12. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
13. Prevent unauthorized use by children or untrained users; restrict
access or disable machine when unattended.
410
MODEL G0814X
6" JOINTER w/STAND &
V-HELICAL CUTTERHEAD
Specifications
WARNING!
Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz
To reduce the risk of serious injury when using this machine:
Full-Load Current: 14A at 110V, 7A at 220V
1. Read & understand owner's manual before operating.
Cutterhead: V-Helical w/Indexable Inserts
2. Always wear approved eye protection and respirator.
Insert Size: 15 x 15 x 2.5mm
3. Only plug power cord into a grounded outlet.
Number of Inserts: 24
4. Except when rabbeting, keep all guards in place and in proper
Replacement Inserts: T32014
operating condition. Always replace guard after rabbeting.
Number of Insert Rows: 4
5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
Maximum Depth of Cut: 1/8"
6. Always use push blocks when face planing.
Maximum Rabbeting Depth: 1/2"
7. Never cut deeper than 1/8" on a single pass.
Cutterhead Speed: 5000 RPM
8. Tie back long hair, roll up sleeves, and DO NOT wear loose
Cuts Per Minute: 20,000
clothing, gloves, or jewelry.
Fence Tilt: 45º, 90º, 135º
9. Turn motor OFF and disconnect power before changing inserts,
Table Size: 47-3/8" x 6-5/8"
adjusting tables/fence, or servicing.
Weight: 245 lbs. 10. Before starting, ensure tables are adjusted properly, inserts are
secure, and jointer is stable.
11. Always support workpiece against fence and table. Never attempt
any operation free-handed.
12. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
13. Prevent unauthorized use by children or untrained users; restrict
access or disable machine when unattended.
REF PART # DESCRIPTION
401 P0814401 CUTTERHEAD EXPOSURE WARNING LABEL
402 P0814402 CUTTERHEAD WARNING LABEL
403 P0814403 EYE/EAR/LUNG WARNING LABEL
404 P0814404 ELECTRICITY LABEL
405 P0814405 MODEL NUMBER LABEL (G0814)
405 P0814X405 MODEL NUMBER LABEL (G0814X)
406 P0814406 GRIZZLY NAMEPLATE-SMALL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
BUY PARTS ONLINE AT GRIZZLY.COM!
-60-
Scan QR code to visit our Parts Store.
Labels & Cosmetics
Failure to keep hands clear exposed between
of cutterhead will result in
serious personal injury.
412
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
407
401
Cutterhead
Failure to keep hands clear
of cutterhead will result in
these lines.
serious personal injury.
411
G0814X
404
409
408
REF PART # DESCRIPTION
407 P0814407 GRIZZLY.COM LABEL
408 P0814408 TOUCH-UP PAINT, GRIZZLY GREEN
409 P0814409 TOUCH-UP PAINT, GRIZZLY BEIGE
410 P0814410 MACHINE ID LABEL (G0814)
410 P0814X410 MACHINE ID LABEL (G0814X)
411 P0814411 DISCONNECT POWER LABEL
412 P0814412 READ MANUAL LABEL
Model G0814/G0814X (Mfd. Since 04/22)
ROTATING CUTTERHEAD BELOW!
Use this guard for all operations
possible, and immediately re-install it
following operations that require its
removal.
KICKBACK HAZARD!
1. Ensure outfeed table is even with
knives.
2. Never exceed maximum depth of cut.
3. Do not stand directly behind workpiece.
ALWAYS USE PUSH BLOCKS!
Push blocks minimize possibility of
operator's hands contacting cutterhead
while cutting.
G0814
405
406
404
402