Related Manuals for LifeFitness G2
Summary of Contents for LifeFitness G2
- Page 1 LEG PRESS ADAPTER KIT FOR G2 GYM SYSTEM WARNING: Read and follow all directions for each step to ensure proper assembly of this product. USER’S GUIDE Version: G2-GLPA-101 Revision: 07/17/08...
-
Page 2: Table Of Contents
9. Children must not be allowed near this machine. Supervise teenagers. Note: In our continuing effort to improve our products, specifications are subject to change. ©2006 Life Fitness, a division of Brunswick Corporation. All rights reserved. www.lifefitness.com... -
Page 3: Important Notes
MPORTANT OTES Thank you for purchasing the Life Fitness G2 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. -
Page 4: Parts List
STEP SPACER 1-11/16” LG 3/8 X 1-3/4” BOLT CABLE L CLIP Note: The LEG PRESS ATTACHMENT (GLP) must be assembled before connecting it to the LifeFitness G2 GYM SYSTEMS DISCARD ! CABLE IGURE • Remove the bolts attaching the FRAME BRACE and CABLE to the BASE as shown in FIGURE 1... - Page 5 • If not already installed, slide one 2” COVER CAP (4) over the FRONT LEG (1) as shown in FIGURE 8 • SECURELY assemble the FRONT LEG (1) to the G2 Gym System using two 3/8 X 4” BOLTS (9), four 3/8” WASHERS (5), two LOW HEIGHT 3/8” LOCK NUTS (6) as shown in FIGURE 2.
- Page 6 IGURE • Assemble the new LEG PRESS CABLE (2) using the previously removed bolts as shown in FIGURE 3. Note: Make sure the LEG PRESS CABLE is running in the grooves of all pulleys and above the retaining bolts.
- Page 7 7 3/8 X 1-3/4” IGURE • SECURELY assemble one 3-1/2” PULLEY (3) to the FRONT LEG (1) using one 3/8 X 1-3/4” BOLT (7) and one 3/8” LOCK NUT (6). See FIGURE 4.
- Page 8 8 3/8 X 2-3/4” IGURE • SECURELY attach the GLP LEG PRESS to the FRONT LEG (1) using two 3/8” X 2-3/4” BOLTS(8), two 3/8” WASHERS (5), and two 3/8” LOCK NUTS (6). See FIGURE 5. SEAT FRAME BRACKET IGURE 7 3/8 X 1-3/4”...
- Page 9 SEAT FRAME BRACKET 3/8 LOCK NUT IGURE 3/8 X 4-3/4” • SECURELY attach the BRACKET (from GLP LEG PRESS) to the SEAT FRAME using two 3/8” X 4-3/4” BOLTS (10), two 3/8” WASHERS (5), and two 3/8” LOCK NUTS (6). See FIGURE 7. 3/8 X 1-3/4”...
- Page 10 SEAT FRAME 3/8 LOCK NUT 3/8 X 4-3/4” 10 IGURE • Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (3) and SECURELY assemble the 3-1/2” PULLEY (3) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (10), two STEP SPACERS 1-19/32”...
- Page 11 SEAT FRAME 3/8” LOCK NUT IGURE 3/8 X 4-3/4” 10 • Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (3) and SECURELY assemble the 3-1/2” PULLEY (3) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (10), two STEP SPACERS 1-19/32”...
- Page 12 SEAT FRAME 3/8 LOCK NUT 3/8 X 4-3/4” 10 IGURE • SECURELY assemble the swivel end of the LEG PRESS CABLE (2) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (10), two STEP SPACERS 1-11/16” (13) and one 3/8” LOCK NUT (6). Note: SECURELY tighten, then back nut off 1/4 turn ABLE OUTING...
- Page 13 ADJUST! ADJUST! IGURE • Before setting the correct amount of tension in the cables, push the HEAD PLATE down, insert the WEIGHT SELECTOR PIN, and perform several repetitions at the leg press station. This will relax the cable system and prevent the HEAD PLATE from lifting up. HANK YOU FOR PURCHASING THE ITNESS RESS...