Mounting Notes - Videx 4000 Series Manual

4000 Series
Art. 4204X
Digital to functional interface with built-in speaker unit & proximity reader
TO CALL A USER
Press the relevant button to call the user: 5 quick beeps will indicate if the system is busy, otherwise the call will be signalled by a
slow intermittent acoustic signal until the call is answered, the conversation time expires (programmable time) or the call is inter-
rupted by pressing a push button for a minimum of 2 seconds. A short intermittent acoustic signal plus the relevant LED switched
ON indicates that the door is open. If a wrong push button is pressed or if there is no answer, a new call will cancel the previous one.

MOUNTING NOTES

When an expansion button module (Art. 404x)
is used combined with speaker units with
inbuilt camera (Art. 4204X-1,Art. 4204X-2)
remember to set the expansion modules
properly in order to avoid overwriting the ad-
dresses; indeed the inbuilt buttons addresses
are already set (Fig. 6).
NOTE: this setting is not valid if you are using
the "Advanced" programming mode (switch
10 in ON position) where the Art. 404x jump-
er cannot be n=0 and the push buttons in-
cluded in Art. 4204X-1 and Art. 4204X-2 are
41 and 42.
PROGRAMMING TAGS IN "STANDARD" PROGRAMMING MODE SWITCH 10 IN OFF POSITION
MASTER CARD
The module is supplied with a master card. The master card is preprogrammed in the factory.
The card is used to add and delete user access tags.
If the master card is lost, a new one will need to be created using the procedure detailed further on in this manual. In this instance,
it will be necessary to reprogram all the user tags. The module allows to store up to 60 user tags.
Note: when the master card is required, place it in front of the reader so that the middle of the card is in front of the middle of the card name holder.
PROGRAMMING USERS TAG
The user tags can be programmed on the module using the master card to access the programming mode:
1. Place the master card in front of the tag reader.
The module emits one high-pitched "beep" sound and the
2. Press the call button (the lower call button in the case of a 2-button external module) "n"
times where n is a value between 1 and 60 and specifies the tag number.
On each press the module emits a low-pitched "beep" sound and the
Note: the external module emits a low-pitched continuous "beeping" sound if an already pro-
grammed location is selected.
3. When the desired memory location is reached the
4. Place the user tag to be programmed in front of the tag reader.
The module emits a low-pitched "beep" sound, the tag is programmed. The
stops flashing and remains illuminated.
Note: the module emits a low-pitched continuous "beeping" sound if an already programmed lo-
cation is selected.
5. Repeat steps 2 to 4 for to program further tags.
6. To exit programming mode:
» Place the master key in front of the tag reader, or
» Wait 10 seconds.
The module emits two low-pitched "beep" sounds indicating it is back in normal
operating mode.
USING TAGS
Place a tag in front of the tag reader:
If the tag is programmed, the external module emits two high-pitched "beep" sounds and acti-
vates the relay. The
If the tag is not programmed, the external module emits two low-pitched "beeping" sounds.
Art. 4204X
- Installation instructions
Fig. 6
LED flashes twice and the
Art. 4204X switch
ON
1 2 3 4 5 6 7 8 9
1
10
Art. 404x jumper
9
8
7
R
6
LED illuminates
LED starts flashing waiting for a tag.
LED illuminates for the door opening time.
- 5 -
Nr.2 Nr.3 Nr.4
OFF OFF OFF
10
n=5
BIP
LED flashes.
BIP
BIIIIIIP
LED
BIP
BIIIIIIP
BIP BIP
BIP BIP
BIIP BIIP
66251895 - V1.1 - 31/01/20
2
1
10
9
8
7
6