Table of Contents
Advertisement
Quick Links
SECURITY SAFE INSTRUCTION MANUAL
FOR SA-PLAT1-BIO, SA-PLAT2-BIO, SA-PLAT3-BIO,
SA-PLAT4-BIO, SA-PLAT1-BIO-DP, SA-PLAT2-BIO-DP,
SA-PLAT3-BIO-DP AND SA-PLAT4-BIO-DP
IMPORTANT:
Please read this information and follow all safety rules carefully before
operating your security safe. Failure to do so will void your warranty.
110521
Advertisement
Table of Contents
Related Manuals for Sanctuary Platinum SA-PLAT1-BIO
Summary of Contents for Sanctuary Platinum SA-PLAT1-BIO
- Page 1 SECURITY SAFE INSTRUCTION MANUAL FOR SA-PLAT1-BIO, SA-PLAT2-BIO, SA-PLAT3-BIO, SA-PLAT4-BIO, SA-PLAT1-BIO-DP, SA-PLAT2-BIO-DP, SA-PLAT3-BIO-DP AND SA-PLAT4-BIO-DP IMPORTANT: Please read this information and follow all safety rules carefully before operating your security safe. Failure to do so will void your warranty. 110521...
-
Page 2: Table Of Contents
TABLE OF CONTENTS IMPORTANT INFORMATION ....................2 1. REGISTRATION ........................ 3 2. UNDERSTANDING YOUR SAFE ..................4 3. INITIAL ENTRY ........................5 4. PROGRAMMING YOUR FINGERPRINT ................7 5. OPENING SAFE WITH PROGRAMMED FINGERPRINT ..........8 6. PROGRAMMING ADDITIONAL FINGERPRINTS ..............8 7. -
Page 3: Important Information
SANCTUARY SAFE. DO NOT LOCK THIS MANUAL OR THE BACKUP KEYS IN YOUR SAFE. Thank you for choosing a Sanctuary safe to protect your valuables. We are committed to securing, organizing and protecting your most important documents, valuables and keepsakes. -
Page 4: Registration
REGISTRATION INFORMATION The information you record onto this page will be required in the event you cannot access the contents of your Sanctuary safe. Please fill out all the required information below and retain for your records and safe keeping. -
Page 5: Understanding Your Safe
2. UNDERSTANDING YOUR SAFE Backup Key Entry (underneath magnetic branding plate) Biometric Scanner Indicator Ring 3-Spoke Handle (SA-PLAT1-BIO has one spoke) Interior Light Tempered Glass Shelves Dead Hooks Reset (SA-PLAT1-BIO only has one shelf ) Locking Bolts Button Battery Compartment Bolt Active Down Holes... -
Page 6: Initial Entry
3. INITIAL ENTRY 1. Locate the backup keys and single spoke inside the plastic bag hanging on the front of the safe. 2. Install the single spoke by inserting into one of the threaded openings and twisting clockwise until you feel the spoke fully lock into place. - Page 7 3. INITIAL ENTRY (Continued) 5. Locate the magnetic key cover inside of your safe. On the front of the safe, remove the backup key and install the magnetic TO ATTACH key cover in this same location as shown. If the backup key is required in the future, the magnetic key cover can then be removed by...
-
Page 8: Programming Your Fingerprint
4. PROGRAMMING YOUR FINGERPRINT 1. On the inside of the safe door, locate the brass cap. Unscrew and remove the cap, giving you access to the reset Reset button button. located under brass 2. Press the reset button. You will hear 1 beep and the indicator ring will illuminate white on the front of the door indicating that... -
Page 9: Opening Safe With Programmed Fingerprint
5. OPENING SAFE WITH PROGRAMMED FINGERPRINT With keys in hand, close and lock the door. PLACE AND HOLD the PROGRAMMED finger pad on scanner, indcator ring will flash white 1 time and beep 1 time to alert scanner is activated. If fingerprint is accepted, indicator ring will GREEN LED = SUCCESS! illuminate green. -
Page 10: Troubleshooting
6. PROGRAMMING ADDITIONAL FINGERPRINTS (Continued) HOLD FOR BEEP Complete section 4 again for each fingerprint zone you would like to program. NOTE: GREEN LED If you experience any problems reading your print, including LIFT FINGER inconsistent readings, note the area of your print that doesn’t work properly, and specifically reprogram that area. -
Page 11: Clearing All Programmed Fingerprints
8. CLEARING ALL PROGRAMMED FINGERPRINTS Hold the reset button for 5 seconds. After 5 seconds, the indicator ring will flash green two times and beep two times to signal that all fingerprints have now been cleared. The safe will not open to any fingerprints until a new fingerprint has been programmed. -
Page 12: Glass Shelf Installation
9. GLASS SHELF INSTALLATION First, remove the protective film from the acrylic mirror back wall. Then, remove the tempered glass shelving from the protective packaging located at the bottom of the safe and gather all provided hardware. Screw all provided shelving brackets into place on both the left and the right walls of the safe using a Phillips head screwdriver. - Page 13 9. GLASS SHELF INSTALLATION (Continued) Maneuver the top shelf into the safe, positioned just below the top brackets. Pull the shelf towards you, passing the shelf through both of the front top brackets. Note: During this step, be sure the shelf slides below and does not make contact with the key hooks located on right wall of the safe.
- Page 14 9. GLASS SHELF INSTALLATION (Continued) Insert the bottom shelf into your safe, in between the top and bottom brackets Move this shelf towards the top of your safe, then slide the shelf down into the front brackets. Note: The PLAT1-BIO model only has one shelf Once the bottom shelf has passed through the front...
-
Page 15: Internal Lighting
10. INTERNAL LIGHTING Internal Light When the safe door is opened, internal lighting activates for 30 seconds. If you need to activate your light longer, you can press the green light activation button on the inner door panel. This will activate the internal lighting for an additional 30 seconds each time it is pressed. -
Page 16: Silent Entry Mode
13. SILENT ENTRY MODE By activating the silent entry mode, the safe will no longer make audible sounds. To turn on silent entry mode, hold a programmed finger on the scanner for 5 seconds beyond your fingerprint being accepted. The green indicator ring will turn off... -
Page 17: Securing Your Safe
16. SECURING YOUR SAFE WARNING: YOUR SAFE IS DESIGNED TO SUPPORT ITSELF WHEN THE DOOR IS OPENED. HOWEVER, CAUTION SHOULD BE USED TO AVOID TIPPING. WHILE SECURING YOUR SAFE BE SURE TO HAVE A SECOND PERSON HOLD AND STABILIZE THE SAFE TO KEEP IT FROM TIPPING, CAUSING INJURY, AND/OR DAMAGE TO THE SAFE AND SURROUNDING STRUCTURES. -
Page 18: Loading Your Safe
17. LOADING YOUR SAFE Store documents or heat sensitive items in the bottom of the safe for greatest protection against fire damage. Store ammunition separately from valuables. Do not put anything in your safe that will put pressure against the door when it is closed. -
Page 19: Lifetime Warranty
LIFETIME WARRANTY SA Consumer Products, Inc. will repair or replace, at their sole discretion, any Sanctuary Safe damaged by fire, forced entry, forced attack or natural flood for the lifetime of the original owner. SA Consumer Products, Inc. will repair or replace, at their sole discretion, any Sanctuary Safe with defective parts, paint or lock for the lifetime or the original owner.