Table of Contents
Related Manuals for Sanctuary SA-PV2M-BIO
Summary of Contents for Sanctuary SA-PV2M-BIO
- Page 1 HOME & OFFICE SECURITY VAULTS | INSTRUCTION MANUAL MODEL: SA-PV2M-BIO IMPORTANT: Please read this information and follow all safety rules carefully before operating your gun vault. Failure to do so will void your warranty. 072921...
-
Page 2: Table Of Contents
TABLE OF CONTENTS IMPORTANT INFORMATION ....................2 1. REGISTRATION ........................ 3 2. UNDERSTANDING YOUR VAULT ..................4 3. INITIAL ENTRY ........................5 4. BATTERY INSTALLATION....................5 5. PROGRAMMING YOUR FINGERPRINT ................6 6. OPENING VAULT WITH RECORDED FINGERPRINT ............7 7. PROGRAMMING ADDITIONAL FINGERPRINTS ..............7 8. -
Page 3: Important Information
SANCTUARY VAULT. DO NOT LOCK THIS MANUAL OR THE BACKUP ACCESS KEYS IN YOUR VAULT. Thank you for choosing a Sanctuary vault to protect your valuables. We are committed to securing, organizing and protecting your most important documents, valuables and keepsakes. -
Page 4: Registration
REGISTRATION INFORMATION The information you record onto this page will be required in the event you cannot access the contents of your Sanctuary vault. Please fill out all the required information below and retain for your records and safe keeping. -
Page 5: Understanding Your Vault
2. UNDERSTANDING YOUR VAULT Biometric Scanner Knob Security Cable Backup Key Entry Port Entry (Under Cover) Battery Removable Compartment Shelf Hooks Security Cable Reset Button (Under Cover) Bolt Down Holes Locking (Under Foam) Bolts... -
Page 6: Initial Entry
3. INITIAL ENTRY 1. Locate the key cover on the LOCK UNDER lockface and remove the KEY COVER backup key cover carefully by pulling the key cover tab. In the future you may place a flat head screw driver in the slot and pry upwards. -
Page 7: Programming Your Fingerprint
5. PROGRAMMING YOUR FINGERPRINT 1. First, remove the black rubber plug that covers the reset button on the door panel. Reset button located inside plastic housing 2. Use a pen tip to press the reset BEEP button. You will hear 1 beep and the indicator ring will illuminate on the front of the door. -
Page 8: Opening Vault With Recorded Fingerprint
6. OPENING VAULT WITH RECORDED FINGERPRINT With keys in hand, close the door. TRY AGAIN Place and hold the PROGRAMMED finger on the scanner, indicator ring will illuminate green and vault door will open. LIGHT If your print is not accepted: you will see 1 red light flash with 1 REPROGRAM sound. -
Page 9: Trouble Shooting
7. PROGRAMMING ADDITIONAL FINGERPRINTS HOLD FOR BEEP Press the reset button and follow Section 5 instructions again, for each fingerprint zone you would like to program. LIFT FINGER If you experience any problems reading your fingerprint, including inconsistent readings, note the area of your fingerprint that doesn’t work properly, and specifically re-program that area. - Page 10 8. TROUBLE SHOOTING (CONTINUED) PROBLEM SOLUTION Make sure batteries are fresh. We suggest high grade alkaline. Do not mix old and new batteries. No not use rechargeable batteries. Make sure you are placing the same part of your finger YOUR PROGRAMMED print on the scanner that was used for programming.
-
Page 11: Lockout Out Mode/ Tamper Protection
9. LOCKOUT MODE/ TAMPER PROTECTION 1. Three consecutive incorrect code entries will put the vault in “Basic Lockout” mode. Scanner is deactivated for 30 seconds. 2. After “Basic Lockout” mode has ended, another three consecutive incorrect code entries will result in “Severe Lockout”... -
Page 12: Proper Placement And Moving Of Vault
12. PROPER PLACEMENT AND MOVING OF VAULT To maximize burglary protection and stability, securing the vault to the floor or table is recommended. SA Consumer Products recommends that you store your vault in a closet, office, basement, bedroom or any other location that is convenient for you but out of direct line of sight from prying eyes. -
Page 13: Maintaining Hinges And Internal Mechanisms
13. SECURING YOUR VAULT (CONTINUED) TOOLS AND HARDWARE NEEDED TO SECURE VAULT TO A WOOD OR CONCRETE SURFACE: • DRILL • 2 STEEL LAG BOLTS (NOT INCLUDED) - SIZE 1/4" X 1.50" TO 2.0" LONG • 3/8� DRILL BIT • 2 STEEL WASHERS (NOT INCLUDED) - 1/4"... -
Page 14: Three Year Warranty
flood for the lifetime of the original owner. SA Consumer Products will repair or replace, at their sole discretion, any Sanctuary vault with defective parts, paint or lock for three years of the original owner purchase date. If SA Consumer Products deems a replacement vault is to be sent, they will pay the freight costs to ship the replacement vault to the original owner.