Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Robe Anolis Ambiane XP56
Summary of Contents for Robe Anolis Ambiane XP56
- Page 1 QR code for user manual Version 1.6...
-
Page 2: Table Of Contents
Ambiane XP56 Pendant Remote Table of contents 1. Attention ..................................3 2. Fixture exterior view ..............................4 3. Installation .................................. 4 3.1. DMX and DALI address setting and control ......................9 3.2 0-10V control ..............................10 4. RDM ..................................10 5. -
Page 3: Attention
Ambiane XP56 Pendant Remote 1. Attention The unit must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. The unit was designed for indoor use only. Do not install the unit near highly inflammable liquids or materials. Do not allow anything to rest on the unit. -
Page 4: Fixture Exterior View
Ambiane XP56 Pendant Remote 2. Fixture exterior view Control unit Hanging wire LED unit supply cable LED unit 3. Installation The Ambiane XP56 Pendant Remote must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Always switch off power supply of the control unit before connecting or disconnecting the control unit or the light unit. - Page 5 Ambiane XP56 Pendant Remote 2. Fasten the ceiling plate M6i (3) to the lower ceiling. 3. Screw the spherical cap (4) with the hanging wire (6) to the ceiling plate M6i (3). 4. Drill the hole (diameter of 8mm) in the lower ceiling for the LED unit supply cable (7). If you wish to have the LED unit supply cable (7) parallel with the hanging wire (6), the distance between the hanging wire and the LED unit supply cable should be 60mm.
- Page 6 Ambiane XP56 Pendant Remote 6. Install the terminal block (9) on the supply cable connect it to the PCB RB 3729 of the control unit (1). 7. Install the terminal block (10) on the DMX cable and connect it to the PCB RB 3729 of the control unit (1). 8.
- Page 7 Ambiane XP56 Pendant Remote Primary power connection Connector Function Power + Power - Secondary power connection Connector Function Power + Power - Max. length of the supply cable between the Ambiane XP56 Pendant Remote and the Ambiane Power XP or Ambiane Power Rack is defined by the following table: Circular cross-section of wire Max.
- Page 8 Ambiane XP56 Pendant Remote 11. Set desired position of the LED unit by means of the three hanging wires (17). If you need to pull the hanging wire (17) out of the supply unit, you have to press and hold the part (21) of the wire lock. 12.
-
Page 9: Dmx And Dali Address Setting And Control
Ambiane XP56 Pendant Remote 3.1. DMX and DALI address setting and control The DIP switch on the control PCB (RB3729) allows you to set DMX address and run a test light. DIP 10 - if it is switched to ON=test light (the fixture lights at 3200K (for RGBW and TW version)) DIP 11 - has to be switched to OFF position to receive DMX 512 and DALI, position ON=0-10V control Note: If DIP 11=OFF (fixture is controlled by DMX and DALI), the last coming command switches the fixture to the corresponding operation mode (DMX operation by a DMX command, DALI operation by a DALI command). -
Page 10: 0-10V Control
RDM allows you to set a DMX address, select DMX mode, readout software version of the fixture etc. It is also used for fixture software update by means of the Robe Uploader. RDM model ID for the Ambiane XP56 Pendant Remote is 0x0109. -
Page 11: Dmx Protocols
Ambiane XP56 Pendant Remote SLOT_INFO SLOT_DESCRIPTION DEFAULT_SLOT_VALUE PARAMETER_DESCRIPTION 5. DMX protocols Variant RGBW, version 1.1 Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Function Type of Channel Channel Channel Channel Channel value control proportional Red LEDs saturation control (0-->100%) 0-255 Red Fine proportional... - Page 12 Ambiane XP56 Pendant Remote Variant TW, version 1.1 Mode 1 Mode 2 Function Type of Channel Channel value control White colour selection 0-255 White from 2700K-->4000K proportional Warm White 0-255 proportional Warm white LEDs saturation control ( 0-->100%) Cool White 0-255 Cool white LEDs saturation control ( proportional...
-
Page 13: Technical Specifications
Ambiane XP56 Pendant Remote 6. Technical specifications Nominal input voltage: 48V DC Input voltage range: 44-50V DC Max. power consumption: 150W Light source: High Power LED module Beam angle: 20°, 30°,45°, 60° Projected Lumen Maintenance: L90B10 >90.000 hrs, Ta = 25°C / 77°F °F) Colour Variants: RGBW (W - 2700K or 4000K), PureWhite, Tunable White, Tungsten Colour Temperature of White:... - Page 14 Ambiane XP56 Pendant Remote Dimensions mm [inch] Ambiane XP56 Pendant Remote 20° Ambiane XP56 Pendant Remote 45° Ambiane XP56 Pendant Remote 60° Ambiane XP56 Pendant Remote 30° Control unit Included items 1 x Ambiane XP56 Pendant Remote 1 x Control unit 1 x Set of cable connectors 1 x User manual Option items...
-
Page 15: Cleaning And Maintenance
The fixture has to be connected to power during software update. Software update by means of the Robe Uploader The ROBE Uploader is a software for automatized software update of Robe and Anolis fixtures. It can take advantage of RDM support. -
Page 16: Disposing Of The Product
The fixtures have to be connected to power. The control PC should be connected to the Internet. The Robe Uploader software and user manual is available at https://www.robe.cz/robe-uploader/ If you do the software update by means of the Robe Uploader, switching fixtures to the update mode (and from the update mode) is made automatically.
Need help?
Do you have a question about the Anolis Ambiane XP56 and is the answer not in the manual?
Questions and answers