Advertisement
Quick Links
—— Installation and Safe Use Manual ——
BA9350SX, PR94UZC, PR95UZC, OL835ZC, OL835ZCS,
OL935ZC, OL935ZCS, OL935ZCX, OL935ZCSX SYSTEMS
Customer Service
(800) 247-7668
P A R T S L I S T
Item
Qty
Description
A
2
Pole Section
B
1
Pole Plate
C
2
Extension Channel
D
1
Backboard "H" Frame
E
2
Pole Plate Bracket
F
2
Extension Channel Bracket
G
8
Pivot Bushings
H
4
3/8" x 8" Hex Bolt
I
4
3/8" Thin Lock Nut
J
8
3/8" x 1" Hex Bolt
K
8
3/8" Flat Washer
L
8
3/8" Lock Washer
M
8
3/8" Hex Nut
N
1
Crank
O
2
1/2" x 5" Hex Bolt
P
2
1/2" Thin Lock Nut
Q
3
Square U-Bolt
R
6
1/2" Flat Washer
S
6
1/2" Lock Washer
T
6
1/2" Hex Nut
U
4
5/16" x 1" Truss Head Screw
V
4
5/16" Flat Washer
W
4
5/16" Lock Washer
X
4
5/16" Hex Nut
Y
1
Backboard
Improper installation, maintenance or use may cause product failure and serious personal injury.
Inspect all contents prior to installation. Report any missing parts to dealer immediately.
Read all instructions before proceeding.
Save this instruction in the event that the manufacture must be contacted in the future for maintenance information.
1.
Call your local utility locating service before digging, usually by dialing 811, to avoid serious injury and service
interruptions. Also avoid lawn sprinkler lines.
2.
Determine the desired position of the pole by taking into consideration that the distance between the face of the
pole and the face of the backboard changes as the rim height is adjusted. At the top position (official 10' rim
height) this distance is approximately 30" and at the lowest point is approximately 43". See Figure 2A.
Date: 3/10/22
Rev: 13
For BA8350, BA8350S, BA9350, BA9350S, BA9350X,
Zip Crank Basketball Systems
N.J.C.
Item
Qty
Description
Z
1
Rim and Net
AA
1
Pole Cap
BB
1
Height Gauge
CC
1
Pointer
DD
3
1/4" Flange Nut
EE
2
1/4" x 1" Hex Bolt
FF
1
Crank Handle
GG
TBD
Quick Dry Concrete (supplied by customer)
HH
1
Pole Padding (if applicable)
II
2
1/4" x 8" Carriage Bolt
JJ
2
1/4" Wing Nut
KK
2
Pre-Drilled Wooden Panel
LL
8
1/2" Button Head Screw (Black)
MM
8
1/2" Lock Washer (Black)
NN
2
Pole Connector Bar
OO
1
5/16" Hex Key
PP
4
"J" Bolt (only on X Systems)
QQ
4
Rebar (only on X Systems)
RR
1
Template (only on X Systems)
SS
12
5/8" Hex Nut (only on X Systems)
TT
4
5/8" Lock Washer (only on X Systems)
UU
8
5/8" Flat Washer (only on X Systems)
VV
4
"J" Bolt Safety Cap (only on X Systems)
WW
1
Warning Label
Warning!
File: Publisher\Inst\BA8350.pub
1
Scan for Supplemental
Installation and
Assembly Video
Ref#: 920271
Advertisement
Related Manuals for Bison BA8350
Summary of Contents for Bison BA8350
- Page 1 —— Installation and Safe Use Manual —— For BA8350, BA8350S, BA9350, BA9350S, BA9350X, BA9350SX, PR94UZC, PR95UZC, OL835ZC, OL835ZCS, OL935ZC, OL935ZCS, OL935ZCX, OL935ZCSX SYSTEMS Scan for Supplemental Customer Service Installation and Assembly Video Zip Crank Basketball Systems (800) 247-7668 P A R T S L I S T...
- Page 2 Proceed to either 4a or 4b depending on the model you are installing. IF YOU ARE INSTALLING A DIRECT BURY SYSTEM (BA8350, BA8350S, BA9350, BA9350S, PR94UZC PR95UZC, OL835ZC, OL835ZCS, OL935ZC, OR OL935ZCS) Your pole is shipped in 2 sections reducing freight costs and handling difficulty and increasing pole rigidity.
- Page 3 12a. Adjustment of the angle of the Pre-Drilled Panels (KK) on the pole to match the ground surface adjacent to the footing by slightly loosening and re-tightening the 1/4” Wing Nuts (JJ) will help keep the pole assembly plumb while concrete is curing. 13a.
- Page 4 IF YOU ARE INSTALLING A REMOVABLE PEDESTAL MOUNT SYSTEM (BA9350X, BA9350SX, OL935ZCX OR OL935ZCSX) Your pole is shipped in 2 sections reducing freight costs and handling difficulty and increasing pole rigidity. The lower section has a 12" square pedestal base. Lay the two different Pole Sections (A) end to end with the drilled holes adjacent to each other.
- Page 5 13b. You are now ready to complete the most critical portion of the installation. Please note (and avoid) these common installation mistakes: Proceeding without reading instructions fully. Stopping short of the required hole size. Underestimated the amount of concrete required, allowing part of base/footing to cure before you ...
- Page 6 18b. Once the concrete is cured you may now remove the upper 5/8" Hex Nuts (SS) from the "J" Bolts (PP) and remove and discard the Template (RR). 19b. Place the 5/8" Hex Nuts (SS) you just removed back on each "J" Bolt (PP) and finger tighten against the nut that is embedded in the concrete footing.
- Page 7 Using a marker or masking tape, mark the pole assembly 84" above the actual playing surface. See Figure 2A. Using 3/8" x 1" Hex Bolts (J), 3/8" Flat Washers (K), 3/8" Lock Washers (L) and 3/8" Hex Nuts (M) attach the two Pole Plate Brackets (E) to the Pole Plate (B) and the two Extension Channel Brackets (F), to one of the Extension Channels (C).
- Page 8 26. Using Pivot Bushings (G), 3/8" x 8" Hex Bolts (H) and 3/8" Thin Lock Nuts (I) attach the lower Extension Channel (C) to the Pole Plate (B). Tighten the 3/8" Thin Lock Nut (I) and then reverse 1/2 turn to ensure the Extension Channel (C) can move freely.
- Page 9 Attach the Backboard "H" Frame (D) to the upper and lower Extension Channels (C) using Pivot Bushings (G), 3/8" x 8" Hex Bolts (H) and 3/8" Thin Lock Nuts (I). Tighten the 3/8" Thin Lock Nuts (I) and then reverse 1/2 turn to allow free movement. See Figure 10. Using the Crank Handle (FF) attempt to raise and lower the Backboard "H"...
- Page 10 Figure 13 Attach Height Gauge (BB) to the top Extension Channel (C) with one 1/4" x 1" Hex Bolt (EE) and 1/4" Flange Nut (DD) in the back mounting hole. Slide the Pointer (CC) onto one 1/4" x 1" Hex Bolt (EE) then install one 1/4"...