Husqvarna Norden 901 2022 Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Motorcycle
  5. Norden 901 2022
  6. Owner's manual

Husqvarna Norden 901 2022 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OWNER'S MANUAL 2022
Norden 901
Art. no. 3402576en

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna Norden 901 2022

Summary of Contents for Husqvarna Norden 901 2022

  • Page 1 OWNER'S MANUAL 2022 Norden 901 Art. no. 3402576en...
  • Page 3 DEAR HUSQVARNA MOTORCYCLES CUSTOMER Congratulations on your decision to purchase a Husqvarna motorcycle. You are now the owner of a state-of- DEAR HUSQVARNA MOTORCYCLES CUSTOMER the-art sports vehicle which, with appropriate care, will bring you pleasure for a long time to come.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS Switches on the right side of the MEANS OF REPRESENTATION......6 handlebar ..........19 Symbols used ........6 6.5.1 Start button/emergency OFF Formats used ........6 switch ..........19 Ignition and steering lock....20 SAFETY ADVICE ..........
  • Page 5 10.7 Applying the brakes ......69 7.24.22 Quick Selector Down...... 47 10.8 Stopping, parking ....... 71 7.24.23 Ride Husqvarna (optional) ....47 10.9 Transporting........72 7.24.24 Bluetooth (optional) ......47 10.10 Towing in the event of a 7.24.25 Phone Pairing (optional) ....48 breakdown ..........
  • Page 6 TABLE OF CONTENTS 13.4 Taking the motorcycle off the front WHEELS, TIRES ..........106 lifting gear ........... 80 15.1 Removing the front wheel ..... 106 13.5 Removing the passenger seat .... 80 15.2 Installing the front wheel ....107 13.6 Mounting the passenger seat .....
  • Page 7 TABLE OF CONTENTS 19.5 Setting the free travel of the clutch lever ..........136 CLEANING, CARE ......... 137 20.1 Cleaning the motorcycle ....137 20.2 Checks and maintenance steps for winter operation ........ 138 STORAGE............140 21.1 Storage ..........140 21.2 Preparing for use after storage ..

  • Page 8: Means Of Representation

    Indicates work that requires expert knowledge and technical understanding. In the interest of your own safety, have this work performed by an authorized Husqvarna Motorcycles workshop. Your motorcycle will be cared for there to the highest degree by specially trained experts using the special tools required.

  • Page 9: Safety Advice 2

    SAFETY ADVICE 2 Use definition – intended use The vehicle is designed and constructed to withstand the usual demands of regular traffic and use on gentle terrain (unpaved roads). This vehicle is not suitable for use on race tracks. Info This vehicle is only authorized for operation on public roads in its homologated version.

  • Page 10: Tampering Warning

    The vehicle should only be used by trained persons. An appropriate driver's license is needed to drive the vehi- cle on public roads. Have malfunctions that impair safety immediately eliminated by an authorized Husqvarna Motorcycles work- shop. Adhere to the information and warning labels on the vehicle.

  • Page 11: Protective Clothing

    – Always wear protective clothing that is in good condition and meets the legal regulations. In the interest of your own safety, Husqvarna Motorcycles recommends that you only operate the vehicle while wearing protective clothing. Work rules Unless specified otherwise, the ignition must be turned off during all work (models with ignition lock, models with remote key) or the engine must be at a standstill (models without ignition lock or remote key).
  • Page 12 The Owner's Manual can be downloaded several times using the QR code or the link on the delivery certificate. The Owner's Manual is also available for download from your authorized Husqvarna Motorcycles dealer and on the Husqvarna Motorcycles website. A printed copy can also be ordered from your authorized Husqvarna Motorcycles dealer.

  • Page 13: Important Notes 3

    Customer service Your authorized Husqvarna Motorcycles dealer will be happy to answer any questions you may have regarding your vehicle and Husqvarna Motorcycles. A list of authorized Husqvarna Motorcycles dealers can be found on the Husqvarna Motorcycles website.

  • Page 14: View Of Vehicle

    4 VIEW OF VEHICLE View of vehicle, front left (example) V02424-01 Clutch lever ( p. 16) Seat lock ( p. 25) Grab handles ( p. 25) Storage compartment on the left Passenger foot pegs ( p. 26) Side stand ( p.

  • Page 15: View Of Vehicle, Rear Right (Example)

    VIEW OF VEHICLE 4 View of vehicle, rear right (example) V02425-01 Storage compartment on the right Light switch ( p. 17) Menu buttons ( p. 18) Turn signal switch ( p. 19) Horn button ( p. 19) Fuel tank filler cap Socket for electrical accessories ( p.

  • Page 16: Serial Numbers

    5 SERIAL NUMBERS Vehicle identification number The vehicle identification number is stamped on the right side of the steering head. 402324-10 Type label The type label is located on the frame on the left. The type label for Australia is located on the frame on the right.

  • Page 17: Engine Number

    SERIAL NUMBERS 5 Engine number The engine number is stamped onto the engine case at the top. H01047-10 Fork part number The fork part number is stamped on the inner side of the fork stub. 402295-10 Shock absorber article number Shock absorber article number is attached the top of the shock absorber.

  • Page 18: Controls

    6 CONTROLS Clutch lever Clutch lever is fitted on the handlebar on the left. V02346-10 Hand brake lever The hand brake lever is fitted on the right side of the handle- bar. The front brake is engaged using the hand brake lever. V02347-10 Throttle grip The throttle grip...

  • Page 19: Light Switch

    CONTROLS 6 6.4.2 Light switch The light switch is fitted on the combination switch on the left. Possible states Low beam on – Light switch in position . In this position, the low beam and the tail light are switched High beam on –...

  • Page 20: Menu Buttons

    6 CONTROLS – Operating the hand brake lever – Operating the foot brake lever – Operating the clutch lever – Turning the throttle grip beyond the basic position – Control of the motorcycle traction control (MTC) – Slip at the rear wheel or lifting front wheel –...

  • Page 21: Turn Signal Switch

    CONTROLS 6 6.4.5 Turn signal switch Turn signal switch is fitted on the combination switch on the left. Possible states Turn signal off Left turn signal, on – Turn signal switch pressed to the left. The turn signal switch returns to the center position after activation.

  • Page 22: Ignition And Steering Lock

    6 CONTROLS Ignition and steering lock The ignition and steering lock is located in front of the upper triple clamp. Possible states Ignition off – In this position, the ignition circuit is interrupted, a running engine stops, and a non-running engine will not start. The ignition key can be removed.

  • Page 23: Supplementary Headlight Switch

    CONTROLS 6 Supplementary headlight switch Supplementary headlight switch is located on the left, next to the combination instrument. Info When the symbol lights up on the switch, the supplemen- tary headlights are switched on. V02370-10 6.10 Socket for electrical accessories Socket for electrical accessories is located on the right, next to the combination instrument.

  • Page 24: Closing The Fuel Tank Filler Cap

    6 CONTROLS – Lift cover of the fuel tank filler cap and insert the ignition key into the lock. Note Danger of damage The ignition key may break if over- loaded. Damaged ignition keys must be replaced. – Push down on the fuel tank filler cap to take pressure off the ignition key.

  • Page 25: Opening The Storage Compartment On The Left

    CONTROLS 6 6.14 Opening the storage compartment on the left Preparatory work – Remove the passenger seat. ( p. 80) – Remove the front rider's seat. ( p. 81) – Remove the left side cover. ( p. 86) Main work –...

  • Page 26: Opening The Storage Compartment On The Right

    6 CONTROLS 6.16 Opening the storage compartment on the right Preparatory work – Remove the passenger seat. ( p. 80) – Remove the front rider's seat. ( p. 81) – Remove the right side cover. ( p. 87) Main work –...

  • Page 27: Tool Set

    CONTROLS 6 6.18 Tool set The left or right storage compartment contains the on-board tool V02361-10 6.19 Grab handles The grab handles are used for moving the motorcycle around. If you carry a passenger, the passenger can hold onto the grab handles during the trip.

  • Page 28: Passenger Foot Pegs

    6 CONTROLS 6.22 Passenger foot pegs The passenger foot pegs can be folded up and down. Possible states Passenger foot pegs folded up – For operation without a • passenger. Passenger foot pegs folded down – For operation with a •...

  • Page 29: Side Stand

    CONTROLS 6 6.25 Side stand The side stand is located on the left of the vehicle. The side stand is used for parking the motorcycle. Info The side stand must be folded up during motorcycle use. The side stand is coupled with the safety starting system; follow the riding instructions.

  • Page 30: Combination Instrument

    7 COMBINATION INSTRUMENT Combination instrument V02176-10 The combination instrument is attached in front of the handlebar. The combination instrument is divided into two function areas. indicator lamps ( p. 30) Display Warning Danger of burns Parts of the combination instrument become very hot in certain situations. In particular, the display gets hot in ambient temperatures above 55 °C (131 °F), during extended sta- tionary periods, for example, at a traffic light, or in direct sunlight.

  • Page 31: Warnings

    If the engine is running and the malfunction indicator lamp lights up, stop (taking care not to endanger yourself or other road users in the process) and contact an authorized Husqvarna Motorcy- cles workshop. The oil pressure warning lamp always lights up as long as the engine is not running.

  • Page 32: Indicator Lamps

    (taking care not to endanger yourself or other road users in the process) and contact an authorized Husqvarna Motorcycles workshop. The oil pressure warning lamp always lights up as long as the engine is not running. If the engine is...

  • Page 33: Display

    COMBINATION INSTRUMENT 7 The malfunction indicator lamp lights up yellow – The OBD has detected a malfunction in the vehicle electronics. Come safely to a halt, and contact an authorized Husqvarna Motor- cycles workshop. The high beam indicator lamp lights up blue – The high beam is switched on.

  • Page 34: Explorer Display (Optional)

    7 COMBINATION INSTRUMENT Favorites display ( p. 37) Heated grip (optional) ( p. 36) Seat heating (optional) ( p. 37) Coolant temperature indicator ( p. 35) Unit for the speedometer Speedometer ( p. 34) Fuel range display Fuel level display ( p.

  • Page 35: Speed

    COMBINATION INSTRUMENT 7 MTC display ( p. 35) ABS display ( p. 35) Heated grip (optional) ( p. 36) Seat heating (optional) ( p. 37) Unit for the engine speed display Coolant temperature indicator ( p. 35) Fuel range display Fuel level display ( p.

  • Page 36: Speedometer

    7 COMBINATION INSTRUMENT 7.10 Speedometer The speed is shown in area of the display. Speed is shown in kilometers per hour km/h or in miles per hour mph. The unit of speed can be configured in the Units menu. V02187-10 7.11 Cruise control indicator The operating state and active cruise control are shown in...

  • Page 37: Ride-Mode Display

    COMBINATION INSTRUMENT 7 7.14 Ride‑Mode display The Ride Mode ( p. 131) setting is shown in area of the display. The riding mode can be configured in the menu Ride Mode. V02188-10 7.15 ABS display The ABS mode setting is shown in the area of the display.

  • Page 38: Fuel Level Display

    7 COMBINATION INSTRUMENT Info If the coolant temperature indicator shows HOT, the indi- cator also starts to flash. If the cooling system overheats, the maximum engine speed is limited. Possible states The engine is cold – The coolant temperature indicator •...

  • Page 39: Seat Heating (Optional)

    COMBINATION INSTRUMENT 7 7.20 Seat heating (optional) The status of the seat heating is shown in area of the display. The seat heating can be configured in the Heating menu. Info The heating level for the passenger seat heating (optional) can be controlled by a switch next to the right grab han- dle.

  • Page 40: Menu

    7 COMBINATION INSTRUMENT Info It is not possible to change the audio volume using the combination switch with every cellphone. The call duration and contact are displayed. Depending on the cellphone settings, the contact is shown by name. You cannot navigate in the menu during an active phone conversation.

  • Page 41: Abs Mode

    COMBINATION INSTRUMENT 7 – Press the UP or DOWN button until Ride Mode is highlighted. Press the SET button to open the menu. – Activate the menu item using the UP or DOWN button. – Press the SET button to select the Ride Mode, which changes coordinated settings for the engine and motorcycle traction control.

  • Page 42: Mtc + Msr

    7 COMBINATION INSTRUMENT Info The ABS mode can be switched during the journey. Do not open the throttle during the selection. When the ABS mode Road is active, ABS controls both wheels. When the Offroad ABS mode is active, ABS only con- trols the front wheel.

  • Page 43: Heating (Optional)

    COMBINATION INSTRUMENT 7 7.24.6 Heating (optional) – Press the SET button when the menu is closed. – Press the UP or DOWN button until Motorcycle is high- lighted. Press the SET button to open the menu. – Press the UP or DOWN button until Heating is highlighted. Press the SET button to open the menu.

  • Page 44: Interface

    7 COMBINATION INSTRUMENT 7.24.9 Interface – Press the SET button when the menu is closed. – Press the UP or DOWN button until Motorcycle is high- lighted. Press the SET button to open the menu. – Press the UP or DOWN button until Interface is highlighted. Press the SET button to open the menu.

  • Page 45: Bike Info

    COMBINATION INSTRUMENT 7 Level 1 allows the maximum slip on the rear wheel, and level 9 the minimum. If the cruise control function is deactivated, the UP and DOWN buttons in the main display or in the Slip Adjuster menu can be used to adjust the Slip Adjuster.

  • Page 46: Trip 1

    7 COMBINATION INSTRUMENT 7.24.15 Trip 1 – Press the SET button when the menu is closed. – Press the UP or DOWN button until Trip Info is highlighted. Press the SET button to open the menu. – Press the UP or DOWN button until Trip 1 is highlighted. Press the SET button to open the menu.

  • Page 47: Audio (Optional)

    COMBINATION INSTRUMENT 7 7.24.17 Audio (optional) Condition ® • Bluetooth function is activated. • The combination instrument is connected to a suitable cell- phone. • The combination instrument is connected to a suitable head- set or the Headset TypeCorded is selected. –...

  • Page 48: Favorites

    7 COMBINATION INSTRUMENT 7.24.19 Favorites Condition • The motorcycle is stationary. – Press the SET button when the menu is closed. – Press the UP or DOWN button until Settings is highlighted. Press the SET button to open the menu. –...

  • Page 49: Quick Selector Down

    Press the SET button to open the menu. – Press the UP or DOWN button until Ride Husqvarna is high- lighted. Press the SET button to open the menu. A suitable cellphone or headset can be paired with the combina- ®...

  • Page 50: Phone Pairing (Optional)

    Press the UP or DOWN button until Settings is highlighted. Press the SET button to open the menu. – Press the UP or DOWN button until Ride Husqvarna is high- V02227-01 lighted. Press the SET button to open the menu.

  • Page 51: Riders Headset (Optional)

    Press the UP or DOWN button until Settings is highlighted. Press the SET button to open the menu. – Press the UP or DOWN button until Ride Husqvarna is high- V02228-01 lighted. Press the SET button to open the menu.

  • Page 52: Shift Light

    7 COMBINATION INSTRUMENT The connection mode for the rider headset can be selected in the Headset Type menu. The headset is connected to the vehicle wirelessly via Blue- ® tooth in Bluetooth Headset mode. The headset is connected directly to the smartphone by a cable in Corded Headset mode.

  • Page 53: Shift Light Rpm2

    COMBINATION INSTRUMENT 7 Info RPM1 can be set in intervals of 500 between 5,500 and 10,000 rpm. RPM1 must not be larger than RPM2. If the engine speed reaches set value RPM1, the shift warning light flashes yellow. 7.24.31 Shift Light RPM2 Condition •...

  • Page 54: Date Format

    7 COMBINATION INSTRUMENT 7.24.34 Date Format Condition • The motorcycle is stationary. – Press the SET button when the menu is closed. – Press the UP or DOWN button until Settings is highlighted. Press the SET button to open the menu. –...

  • Page 55: Pressure

    COMBINATION INSTRUMENT 7 7.24.38 Pressure Condition • The motorcycle is stationary. – Press the SET button when the menu is closed. – Press the UP or DOWN button until Settings is highlighted. Press the SET button to open the menu. –...

  • Page 56: Extra Functions

    Info The optional extra functions are listed. The current Husqvarna Motorcycles Technis- ches Zubehör and available software for your vehicle can be found on the Husqvarna Motorcycles website. 7.24.42 Setting the time and date Condition The motorcycle is stationary. –...
  • Page 57 COMBINATION INSTRUMENT 7 Setting the date – Press the UP or DOWN button until Set Date is high- lighted. Press the SET button to open the menu. – Press the UP or DOWN button until Day is highlighted. Press the SET button to open the menu. –...

  • Page 58: Ergonomics

    8 ERGONOMICS Setting the front rider's seat Preparatory work – Remove the passenger seat. ( p. 80) – Remove the front rider's seat. ( p. 81) Alternative 1 – Attach the front rider's seat to the fuel tank at the recesses , and push the front rider's seat down and forward at the same time.

  • Page 59: Adjusting The Basic Position Of The Clutch Lever

    ERGONOMICS 8 – Remove screws . Take off the handlebar clamps Position the handlebar so that screws are accessible. Info Cover the components to protect them against dam- age. Do not kink the cables and lines. – Remove screws . Take off handlebar supports –...

  • Page 60: Adjusting The Basic Position Of The Hand Brake Lever

    8 ERGONOMICS Adjusting the basic position of the hand brake lever – Push hand brake lever forward. – Adjust the basic position of the hand brake lever to your hand size by turning adjusting screw Info Turn the adjusting screw clockwise to decrease the distance between the hand brake lever and the han- dlebar.

  • Page 61: Checking The Basic Position Of The Shift Lever

    ERGONOMICS 8 – Detach spring – Loosen nut Press the foot brake lever downwards to make this easier. – Turn the push rod to set the basic position of the foot brake lever. V02429-10 Info The range of adjustment is limited. The screw must be screwed in by at least five full turns.

  • Page 62: Adjusting The Basic Position Of The Shift Lever

    8 ERGONOMICS – Sit on the vehicle in the riding position and determine distance between the upper edge of your boot and the shift lever. Distance between shift lever 10 … 20 mm (0.39 … and upper edge of boot 0.79 in) »...

  • Page 63: Preparing For Use 9

    When using your vehicle, remember that others may feel disturbed by excessive noise. – Make sure that the pre-sale inspection work has been carried out by an authorized Husqvarna Motorcycles workshop. You will receive a delivery certificate when the vehicle is handed over.

  • Page 64: Running In The Engine

    9 PREPARING FOR USE – Run the engine in. ( p. 62) Running in the engine – During the running-in phase, do not exceed the specified engine speed. Guideline Maximum engine speed During the first: 1,000 km (620 mi) 6,500 rpm After the first: 1,000 km (620 mi) 9,800 rpm –...
  • Page 65 PREPARING FOR USE 9 Warning Danger of accidents Pieces of luggage which have slipped impair the handling characteristic. – Check that your luggage is fixed properly at regular intervals. Warning Fire hazard The hot exhaust system may burn luggage. – Fasten your luggage in such a way that it cannot be burned or singed by the hot exhaust system. –...

  • Page 66: Riding Instructions

    10 RIDING INSTRUCTIONS 10.1 Checks and maintenance measures when preparing for use Info Before every trip, check the condition of the vehicle and ensure that it is roadworthy. The vehicle must be in perfect technical condition when it is being operated. –...

  • Page 67: Starting Off

    RIDING INSTRUCTIONS 10 After you switch on the ignition, you can hear the fuel pump working for about two seconds. The function check of the combination instrument is run at the same time. The ABS warning lamp lights up and goes back out after starting off.

  • Page 68: Easy Shift

    10 RIDING INSTRUCTIONS 10.4 Easy Shift If Easy Shift is activated, you can shift up and down without operating the clutch. Because there is no need to close the throttle grip, uninterrupted gear shifts are possible. Easy Shift uses the shifter shaft position to check whether or not a shift should be initiated, and sends a corresponding signal to the engine control unit.
  • Page 69 RIDING INSTRUCTIONS 10 Warning Danger of accidents A risky riding style constitutes a major risk. – Comply with traffic regulations and ride defensively and with foresight to detect sources of danger as early as possible. Warning Danger of accidents Cold tires have reduced road grip. –...
  • Page 70 10 RIDING INSTRUCTIONS Info If unusual noises occur while riding, stop immediately (taking care not to endanger yourself or other road users in the process), switch off the engine, and contact an authorized Husqvarna Motorcycles work- shop. – Shift into a higher gear when conditions allow (incline, road situation, etc.).

  • Page 71: Msr

    Danger of accidents A spongy pressure point on the front or rear brake reduces braking efficiency. – Check the brake system and do not continue riding until the problem is eliminated. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Warning Danger of accidents The brake system fails in the event of overheating.
  • Page 72 10 RIDING INSTRUCTIONS Warning Danger of accidents Higher total weight increases the stopping distance. – Take the longer stopping distance into account when carrying a passenger or luggage with you. Warning Danger of accidents Salt on the roads impairs the brake system. –...

  • Page 73: Stopping, Parking

    RIDING INSTRUCTIONS 10 10.8 Stopping, parking Warning Risk of injury People who act without authorization endanger themselves and others. – Do not leave the vehicle unattended if the engine is running. – Protect the vehicle against access by unauthorized persons. – Lock the steering and remove the ignition key if you leave the vehicle unattended.

  • Page 74: Transporting

    10 RIDING INSTRUCTIONS 10.9 Transporting Note Danger of damage The parked vehicle can roll away or fall over. – Park the vehicle on a firm and level surface. Note Fire hazard Hot vehicle components pose a fire hazard and explosion risk. – Do not park the vehicle near to materials which are highly flammable or explosive.

  • Page 75: Refueling

    – Refuel only with clean fuel that meets the specified standards. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Note Environmental hazard Improper handling of fuel is a danger to the environment. –...

  • Page 76: Service Schedule

    Different service intervals may apply in your country, depending on the local operating conditions. Individual service intervals and scopes may change in the course of technical developments. The most up-to- date service schedule can always be found on Husqvarna Motorcycles Dealer.net. Your authorized Husqvarna Motorcycles dealer will be glad to advise you.

  • Page 77: Recommended Work

    ● Final check: Check the vehicle is roadworthy and take a test ride. ○ ● ● ● ● Read out the fault memory after the test ride using the Husqvarna Motorcycles diag- nostics tool. ○ ● ● ● ● Set the service interval display.

  • Page 78: Tuning The Chassis

    12 TUNING THE CHASSIS 12.1 Fork/shock absorber The fork and the shock absorber offer many options of adapting the suspension to the riding style and the payload. Info The recommendations for the suspension setting are shown in table . The table is located under the seat on the air filter box.

  • Page 79: Adjusting The Rebound Damping Of The Fork

    Risk of injury Parts of the shock absorber will move around if the shock absorber is detached incor- rectly. The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Turn adjusting screw clockwise up to the last perceptible click.

  • Page 80: Adjusting The Spring Preload Of The Shock Absorber

    12 TUNING THE CHASSIS Info Turn clockwise to increase the damping; turn counterclockwise to reduce damping when the shock absorber rebounds. 12.5 Adjusting the spring preload of the shock absorber Warning Danger of accidents Modifications to the suspension setting may seriously alter the handling charac- teristic.

  • Page 81: Service Work On The Chassis 13

    SERVICE WORK ON THE CHASSIS 13 13.1 Raising the motorcycle with rear lifting gear Note Danger of damage The parked vehicle can roll away or fall over. – Park the vehicle on a firm and level surface. – Mount retaining adapter on the link fork. –...

  • Page 82: Taking The Motorcycle Off The Front Lifting Gear

    13 SERVICE WORK ON THE CHASSIS – Move the handlebar to the straight-ahead position. – Use suitable lifting gear when attaching the steering stem. – Align the front lifting gear with the fork legs. Info Always raise the motorcycle at the rear first. –...

  • Page 83: Mounting The Passenger Seat

    SERVICE WORK ON THE CHASSIS 13 13.6 Mounting the passenger seat – Hook holding lugs of the passenger seat into the bushings on the subframe, lower the front, and simultaneously push backward. – Insert locking pin into the lock housing and push down the front of the passenger seat until the locking pin engages with an audible click.

  • Page 84: Checking For Chain Dirt

    13 SERVICE WORK ON THE CHASSIS 13.9 Checking for chain dirt – Check the chain for coarse dirt accumulation. » If the chain is very dirty: – Clean the chain. ( p. 82) 400678-01 13.10 Cleaning the chain Warning Danger of accidents Lubricants on the tires reduces the road grip. –...

  • Page 85: Checking The Chain Tension

    SERVICE WORK ON THE CHASSIS 13 13.11 Checking the chain tension Warning Danger of accidents Incorrect chain tension damages components and results in accidents. If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear wheel bearings wear more quickly. Some components may break if overloaded. If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket.

  • Page 86: Checking The Chain, Rear Sprocket, Engine Sprocket, And Chain Guide

    13 SERVICE WORK ON THE CHASSIS Main work – Loosen nut – Loosen nuts – Adjust the chain tension by turning adjusting screws left and right. Guideline Chain tension 2 … 5 mm (0.08 … 0.2 in) Turn the adjusting screws on the left and right so that the markings on the left and right chain adjusters are in...
  • Page 87 SERVICE WORK ON THE CHASSIS 13 – Shift the transmission into neutral – Pull on the lower chain section with the specified weight Guideline Weight, chain wear mea- 15 kg (33 lb.) surement – Measure distance of 18 chain rollers in the lower chain section.

  • Page 88: Removing The Left Side Cover

    13 SERVICE WORK ON THE CHASSIS – Check the chain sliding guard for wear. » If continuous signs of wear to the chain are visible on the chain sliding guard in the area marked: – Change the chain sliding guard. »...

  • Page 89: Installing The Left Side Cover

    SERVICE WORK ON THE CHASSIS 13 13.15 Installing the left side cover Main work – Position the left side cover with holding lug on bush- and push backward. The left side cover engages under the tail part. – Press the left side cover in area into rubber bushing and press into rubber bushing in area...

  • Page 90: Installing The Right Side Cover

    13 SERVICE WORK ON THE CHASSIS 13.17 Installing the right side cover Main work – Position the right side cover with holding lug on bush- and push backward. The right side cover engages under the tail part. – Press the right side cover in the area into rubber bush- and press into rubber bushing in area...

  • Page 91: Installing The Battery Cover

    SERVICE WORK ON THE CHASSIS 13 13.19 Installing the battery cover Main work – Position the battery cover with holding lugs on brack- of the center fuel tank spoiler and push it forward. Make sure the holding lugs engage in the brackets. V02387-10 Finishing work –...

  • Page 92: Installing The Center Fuel Tank Spoiler

    13 SERVICE WORK ON THE CHASSIS 13.21 Installing the center fuel tank spoiler Main work – Position the center fuel tank spoiler and press the holding lugs in area into the bracket. Make sure the holding lugs engage in the brackets. –...

  • Page 93: Installing The Left Fuel Tank Spoiler

    SERVICE WORK ON THE CHASSIS 13 13.23 Installing the left fuel tank spoiler Main work – Position the left fuel tank spoiler and press it into the brack- ets in area Make sure the holding lugs engage in the brackets. –...

  • Page 94: Removing The Right Fuel Tank Spoiler

    13 SERVICE WORK ON THE CHASSIS 13.24 Removing the right fuel tank spoiler Preparatory work – Remove the passenger seat. ( p. 80) – Remove the front rider's seat. ( p. 81) – Remove the battery cover. ( p. 88) –...

  • Page 95: Removing The Front Fender

    SERVICE WORK ON THE CHASSIS 13 – Mount screws , but do not tighten yet. Guideline Screw, trim 3 Nm (2.2 lbf ft) The front edge of the right fuel tank spoiler is evenly aligned. – Tighten all the screws of the right fuel tank spoiler. Guideline Screw, trim 3 Nm (2.2 lbf ft)

  • Page 96: Cleaning The Dust Boots Of The Fork Legs

    13 SERVICE WORK ON THE CHASSIS 13.28 Cleaning the dust boots of the fork legs Preparatory work – Raise the motorcycle with the rear lifting gear. ( p. 79) – Lift the motorcycle with the front lifting gear. ( p. 79) Main work –...

  • Page 97: Installing The Windshield

    SERVICE WORK ON THE CHASSIS 13 13.30 Installing the windshield – Position windshield – Mount and tighten screws Guideline Screw, windshield M5x14 5 Nm (3.7 lbf ft) V02384-10 13.31 Removing left fuel tank cover – Remove fitting – Remove screws –...

  • Page 98: Installing The Left Fuel Tank Cover

    13 SERVICE WORK ON THE CHASSIS 13.32 Installing the left fuel tank cover – Position the left fuel tank cover. – Mount screws , but do not tighten yet. Guideline Screw, tank guard M6x25 10 Nm (7.4 lbf ft) on engine guard, front –...

  • Page 99: Installing The Right Fuel Tank Cover

    SERVICE WORK ON THE CHASSIS 13 13.34 Installing the right fuel tank cover – Position the right fuel tank cover. – Mount screws , but do not tighten yet. Guideline Screw, tank guard M6x25 10 Nm (7.4 lbf ft) on engine guard, front –...

  • Page 100: Installing The Engine Guard

    13 SERVICE WORK ON THE CHASSIS – Remove screws and engine guard V02437-10 13.36 Installing the engine guard – Position engine guard – Mount screws , but do not tighten yet. Guideline Screw, engine M6x10 10 Nm (7.4 lbf ft) Loctite ®...

  • Page 101: Brake System 14

    – Only use spare parts on the brake system which have been approved and recommended by Husqvarna Motorcycles. – Only use tires/wheels approved by Husqvarna Motor- cycles with the corresponding speed index. – Maintain the specified tire pressure. – Ensure that service work and repairs are performed professionally.

  • Page 102: Checking Brake Discs

    Warning Danger of accidents Worn-out brake discs reduce the braking effect. – Make sure that worn-out brake discs are replaced immediately. (Your authorized Husqvarna Motor- cycles workshop will be glad to help.) – Check front and rear brake disc thickness at multiple points...

  • Page 103: Checking The Front Brake Fluid Level

    – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

  • Page 104: Checking The Front Brake Linings

    Warning Danger of accidents Worn-out brake linings reduce the braking effect. – Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) Warning Danger of accidents Damaged brake discs reduce the braking effect.

  • Page 105: Checking The Free Travel Of The Foot Brake Lever

    Warning Danger of accidents Old brake fluid reduces the braking effect. – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

  • Page 106: Adding Rear Brake Fluid

    Danger of accidents Old brake fluid reduces the braking effect. – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Note Environmental hazard Hazardous substances cause environmental damage.

  • Page 107: Checking The Rear Brake Linings

    Warning Danger of accidents Worn-out brake linings reduce the braking effect. – Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) Warning Danger of accidents Damaged brake discs reduce the braking effect.

  • Page 108: Wheels, Tires

    15 WHEELS, TIRES 15.1 Removing the front wheel Preparatory work – Raise the motorcycle with the rear lifting gear. ( p. 79) – Lift the motorcycle with the front lifting gear. ( p. 79) Main work – Remove screw and pull wheel speed sensor out of the hole.

  • Page 109: Installing The Front Wheel

    WHEELS, TIRES 15 15.2 Installing the front wheel Warning Danger of accidents Oil or grease on the brake discs reduces the braking effect. – Always keep the brake discs free of oil and grease. – Clean the brake discs with brake cleaner when necessary. –...

  • Page 110: Removing The Rear Wheel

    15 WHEELS, TIRES – Position both brake calipers. The brake linings are correctly positioned. – Mount screws on both sides but do not tighten yet. Guideline Screw, front M10x1.25 45 Nm (33.2 lbf ft) ® Loctite 243™ brake caliper – Operate the hand brake lever repeatedly until the brake lin- ings are in contact with the brake disc and there is a pressure point.
  • Page 111 WHEELS, TIRES 15 Main work – Manually press the brake caliper toward the brake disc to push back the brake piston. – Remove screw and pull wheel speed sensor out of the hole. – Remove nut . Take off chain adjuster –...

  • Page 112: Installing The Rear Wheel

    15 WHEELS, TIRES 15.4 Installing the rear wheel Warning Danger of accidents Oil or grease on the brake discs reduces the braking effect. – Always keep the brake discs free of oil and grease. – Clean the brake discs with brake cleaner when necessary. Warning Danger of accidents There is no braking effect to start with at the rear brake after installing the rear wheel.

  • Page 113: Checking The Rear Hub Damping Rubber Pieces

    WHEELS, TIRES 15 Nut, rear wheel M25x1.5 90 Nm (66.4 lbf ft) Thread and contact spindle area of wheel spindle greased – Position wheel speed sensor in the hole. – Mount and tighten screw Guideline Screw, rear wheel 6 Nm (4.4 lbf ft) speed sensor –...

  • Page 114: Checking The Tire Condition

    Warning Danger of accidents If a tire bursts while riding, the vehicle becomes uncontrollable. – Ensure that damaged or worn tires are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) Warning Danger of crashing Different tire tread patterns on the front and rear wheel impair the handling char- acteristic.

  • Page 115: Checking Tire Pressure

    Other spokes will become looser as a result. – Check spoke tension regularly, and in particular on a new vehicle. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

  • Page 116: Tubeless Tire System

    The rigid rim design results in a wire spoke wheel that is almost entirely maintenance-free. Husqvarna Motorcycles recommends that the rim seal band is changed after 5 years at the latest, regardless of the actual state of wear.
  • Page 117 WHEELS, TIRES 15 (Option: With TPMS) Note Material damage Tire repair spray damages the tire pres- sure sensor. – Note that after using tire repair spray, the tire pressure sensor may need to be replaced.

  • Page 118: Electrical System

    16 ELECTRICAL SYSTEM 16.1 Removing the 12-V battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns. – Keep 12 V batteries out of the reach of children. – Wear suitable protective clothing and safety glasses. – Avoid contact with battery acid and battery gases.

  • Page 119: Installing The 12-V Battery

    ELECTRICAL SYSTEM 16 – Disconnect negative cable from the 12-V battery. – Remove positive terminal cover – Disconnect positive cable from the 12-V battery. – Pull the 12-V battery upwards and out of the battery com- partment. V02451-10 16.2 Installing the 12-V battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns.
  • Page 120 16 ELECTRICAL SYSTEM Main work – Position the 12-V battery in the battery compartment. 12-V battery (HTZ12A-BS) ( p. 148) The battery terminals face opposite the direction of travel. – Connect positive cable to the 12-V battery. Guideline Screw, battery termi- 4.5 Nm (3.32 lbf ft) –...

  • Page 121: Charging The 12-V Battery

    ELECTRICAL SYSTEM 16 16.3 Charging the 12-V battery Warning Risk of injury Battery acid and battery gases cause serious chemical burns. – Keep 12 V batteries out of the reach of children. – Wear suitable protective clothing and safety glasses. – Avoid contact with battery acid and battery gases.

  • Page 122: Changing The Main Fuse

    16 ELECTRICAL SYSTEM – Connect a battery charger to the 12-V battery. Switch on the battery charger. Guideline The battery charger must be suitable for the 12-V battery. Info Never remove cover Charge the 12-V battery to a maximum of 10% of the capacity specified on battery housing V02478-10 –...

  • Page 123: Changing The Abs Fuses

    ELECTRICAL SYSTEM 16 Main work – Remove protection cap V02440-10 – Remove faulty main fuse Info A faulty fuse has a burned-out fuse wire A spare fuse is located in the starter relay. – Insert a new main fuse. Fuse (58011109130) ( p.

  • Page 124: Changing The Fuses Of Individual Electrical Power Consumers

    16 ELECTRICAL SYSTEM Preparatory work – Remove the passenger seat. ( p. 80) – Remove the front rider's seat. ( p. 81) To change the fuse of the ABS hydraulic unit: – Remove the protection cap and fuse Info A faulty fuse has a burned-out fuse wire –...
  • Page 125 ELECTRICAL SYSTEM 16 Main work – Open fuse box cover F03305-10 – Remove the faulty fuse. Guideline Fuse 1 - 10 A - ignition, alarm system (optional) Fuse 2 - 10 A - ignition, engine control unit, electronic fuel injection, fuel vapor retention system, lambda sensor, immobilizer Fuse 3 - 10 A - fuel pump Fuse 4 - 15 A - radiator fan...

  • Page 126: Checking The Headlight Setting

    16 ELECTRICAL SYSTEM 16.7 Checking the headlight setting – Park the vehicle on a horizontal surface in front of a light- colored wall and make a mark at the height of the center of the low beam headlight. – Make another mark at a distance under the first marking.

  • Page 127: Checking The Supplementary Headlight Setting

    ELECTRICAL SYSTEM 16 16.9 Checking the supplementary headlight setting – Park the vehicle on a horizontal surface in front of a light- colored wall and make a mark at the height of the center of the low beam headlight. – Make another mark at a distance under the first marking.

  • Page 128: Diagnostics Connector

    16 ELECTRICAL SYSTEM 16.11 Diagnostics connector Diagnostics connector is located under the battery cover. V02449-10 16.12 Front ACC1 and ACC2 Installation location – The front power supply ACC1 is located behind the head- light. The front power supply ACC2 is located behind the mask support cover.
  • Page 129 ELECTRICAL SYSTEM 16 Info The power supplies are protected by a fuse; however, this fuse also protects other electrical power consumers. The maximum continuous load is therefore significantly lower than the value of the fuse. Do not use a stronger fuse. The power supply ACC1 is switched to permanent posi- tive;...

  • Page 130: Cooling System

    17 COOLING SYSTEM 17.1 Cooling system Water pump in the engine ensures forced circulation of the coolant. The pressure resulting from the warming of the cooling system is regulated by a valve in radiator cap . Heat expansion causes excess coolant to flow into compensating tank .

  • Page 131: Correcting The Coolant Level In The Compensating Tank

    COOLING SYSTEM 17 – Check the coolant level in the compensating tank. The coolant level must be between MIN and MAX. » If there is no coolant in the compensating tank: – Check the cooling system for leaks. Info Do not start up the motorcycle! –...
  • Page 132 17 COOLING SYSTEM – Add coolant until the coolant reaches the specified level. Guideline The coolant level must be between MIN and MAX. Coolant ( p. 157) – Mount cover of the compensating tank. Guideline Compensating tank 1.1 Nm (0.81 lbf ft) V02411-10 cover...

  • Page 133: Tuning The Engine 18

    TUNING THE ENGINE 18 18.1 Ride Mode Possible states Street – Homologated performance with balanced response; • the motorcycle traction control allows normal slip on the rear wheel. The Anti-Wheelie mode is active. Rain – Reduced homologated performance for better rid- •...

  • Page 134: Slip Adjustment (Optional)

    18 TUNING THE ENGINE Info When the motorcycle traction control is active, the TC indicator lamp flashes. When motorcycle traction control is switched off, the TC indicator lamp lights up. 18.3 Slip adjustment (optional) The spin adjuster is a motorcycle traction control function. The slip adjustment allows the motorcycle traction control to be tuned through nine levels to the desired characteristic map.

  • Page 135: Service Work On The Engine 19

    SERVICE WORK ON THE ENGINE 19 19.1 Checking the engine oil level Info The engine oil level must be checked at normal engine operating temperature. – Stand motorcycle upright on a horizontal surface. – Check the engine oil level. Info After switching off the engine, wait one minute before checking the level.
  • Page 136 19 SERVICE WORK ON THE ENGINE – Remove oil drain plugs along with the magnets, the O- rings, and the oil screens. V02446-10 – Remove screws . Take off oil filter cover with the O- ring. – Pull oil filter out of the oil filter housing.

  • Page 137: Adding Engine Oil

    Engine oil (SAE 10W/50) ( p. 157) Info In order to achieve optimal engine oil performance, it is not advisable to mix different engine oils. Husqvarna Motorcycles recommends changing the H01066-10 engine oil. – Mount and tighten filler plug with the O-ring.

  • Page 138: Checking The Free Travel Of The Clutch Lever

    19 SERVICE WORK ON THE ENGINE 19.4 Checking the free travel of the clutch lever Note Clutch damage If there is no free travel by the clutch lever, the clutch will begin to slip. – Check the free travel of the clutch lever each time before using the motorcycle. –...

  • Page 139: Cleaning, Care 20

    CLEANING, CARE 20 20.1 Cleaning the motorcycle Note Material damage Components become damaged or destroyed if a pressure cleaner is used incorrectly. The high pressure forces water into the electrical components, connectors, throttle cables, and bearings, etc. Pressure which is too high causes malfunctions and destroys components. –...

  • Page 140: Checks And Maintenance Steps For Winter Operation

    20 CLEANING, CARE Info The heat produced causes water at inaccessible loca- tions in the engine and on the brake system to evapo- rate. – After the motorcycle has cooled down, lubricate all moving parts and pivot points. – Clean the chain. ( p.
  • Page 141 CLEANING, CARE 20 Info Corrosion inhibitor must not come in contact with the brake discs as this would greatly reduce the braking force. – Clean the chain. ( p. 82)

  • Page 142: Storage

    21 STORAGE 21.1 Storage Info If you plan to garage the motorcycle for a longer period, perform the following steps or have them per- formed. Before storing the motorcycle, check all parts for function and wear. If service, repairs, or replacements are necessary, you should do this during the storage period (less workshop overload).

  • Page 143: Troubleshooting 22

    Quick release coupling not Join quick release coupling. joined – Malfunction in the electronic Read out the fault memory using the fuel injection Husqvarna Motorcycles diagnostics tool. – Throttle opened while starting When starting, DO NOT open the throttle. –...
  • Page 144 Stop, switch off the ignition, start wheels differ greatly again. – Malfunction in ABS Read out the ABS fault memory using the Husqvarna Motorcycles diagnos- tics tool. – High oil consumption Engine vent hose bent Route the vent hose without bends or change it if necessary.

  • Page 145: Technical Data 23

    TECHNICAL DATA 23 23.1 Engine Design 2-cylinder 4-stroke in-line engine, water-cooled Displacement 890 cm³ (54.31 cu in) Stroke 68.8 mm (2.709 in) Bore 90.7 mm (3.571 in) Compression ratio 13.5:1 Control DOHC, 4 valves per cylinder controlled via cam lever, chain drive Valve diameter, intake 37 mm (1.46 in)

  • Page 146: Engine Tightening Torques

    23 TECHNICAL DATA 23.2 Engine tightening torques ® Screw plug, water pump drain EJOTALtracs Plus 60x14 8 Nm (5.9 lbf ft) ® Loctite 243™ hole ® Screw, bleeder flange EJOTALtracs M6x12 8 Nm (5.9 lbf ft) ® Loctite 243™ Hose clamp, intake flange 2.5 Nm (1.84 lbf ft) Nozzle, engine vent 2 Nm (1.5 lbf ft)
  • Page 147 TECHNICAL DATA 23 Screw, main shaft bearing support M6 10 Nm (7.4 lbf ft) ® Loctite 243™ Screw, oil pan M6x30 10 Nm (7.4 lbf ft) Screw, oil pan M6x35 10 Nm (7.4 lbf ft) Screw, oil pump cover 10 Nm (7.4 lbf ft) ®...

  • Page 148: Capacities

    23 TECHNICAL DATA Screw, conrod bearing M8x0.75 1st stage 5 Nm (3.7 lbf ft) 2nd stage 20 Nm (14.8 lbf ft) 3rd stage 90° Screw support and thread oiled Screw, engine sprocket 60 Nm (44.3 lbf ft) Loctite ® 2701™ Spark plug 11 Nm (8.1 lbf ft) Oil pressure sensor...

  • Page 149: Fuel

    TECHNICAL DATA 23 23.3.3 Fuel Please observe the labels on EU fuel pumps. A00420-10 Fuel reserve, approx. 3 l (3 qt.) Total fuel tank capacity, approx. 19 l (5 US gal) Super unleaded (ROZ 95) p. 158) 23.4 Chassis Frame Lattice frame made of chrome molybdenum steel tubing, powder-coated WP APEX OC...

  • Page 150: Electrical System

    150/70 - 18 M/C 70V M+S TL Pirelli SCORPION RALLY STR Pirelli SCORPION RALLY STR The tires specified represent one of the possible series production tires. Additional information is available in the Service section under: www.husqvarna-motorcycles.com 23.7 Fork Fork article number 0221C141V201102...

  • Page 151: Shock Absorber

    TECHNICAL DATA 23 Spring rate Medium (standard) 6.5 N/mm (37.1 lb/in) Fork length 878.5 mm (34.587 in) Fork oil per fork leg 475 ± 5 ml (16.06 ± 0.17 fl. oz.) Fork oil (SAE 5) ( p. 158) 23.8 Shock absorber Shock absorber article number 15.15.7U.30 Shock absorber...
  • Page 152 23 TECHNICAL DATA Collar screw, bottom instrument M5x20 5 Nm (3.7 lbf ft) support Remaining nuts, chassis 5 Nm (3.7 lbf ft) Remaining screws, chassis 5 Nm (3.7 lbf ft) Screw for throttle grip 3.5 Nm (2.58 lbf ft) Screw, air filter box 3 Nm (2.2 lbf ft) Screw, air filter box, downwards M5x20...
  • Page 153 TECHNICAL DATA 23 Nut, hand brake lever Attach torque to nut. 10 Nm (7.4 lbf ft) Nut, push rod, foot brake lever 6 Nm (4.4 lbf ft) Nut, shift rod M6LH 6 Nm (4.4 lbf ft) Remaining nuts, chassis 10 Nm (7.4 lbf ft) Remaining screws, chassis 10 Nm (7.4 lbf ft) Screw, 6-D sensor...
  • Page 154 23 TECHNICAL DATA Screw, ignition lock (tamper-proof Tighten until the head tears off. screw) ® Loctite 243™ Screw, license plate holder on M6x18 10 Nm (7.4 lbf ft) ® Loctite 243™ lower rear panel Screw, license plate holder on M6x16 10 Nm (7.4 lbf ft) ®...
  • Page 155 TECHNICAL DATA 23 Screw, activated carbon filter M8x16 25 Nm (18.4 lbf ft) ® Loctite 243™ holder fastening Screw, bottom triple clamp 12 Nm (8.9 lbf ft) Screw, case holder M8x20 25 Nm (18.4 lbf ft) ® Loctite 243™ Screw, cross member in rear M8x35 25 Nm (18.4 lbf ft) ®...
  • Page 156 23 TECHNICAL DATA Screw, side stand 40 Nm (29.5 lbf ft) ® Loctite 243™ Screw, subframe 50 Nm (36.9 lbf ft) ® Loctite 243™ Banjo bolt, brake line M10x1 25 Nm (18.4 lbf ft) Nut, turn signal M10x1.25 4 Nm (3 lbf ft) Screw, front brake caliper M10x1.25 45 Nm (33.2 lbf ft)

  • Page 157: Declarations Of Conformity 24

    KTM AG hereby declares that the Immo641 wireless system conforms with the relevant guidelines. The full text of the Declaration of Conformity is available at the following Internet address. Certification website: http://www.husqvarna-motorcycles.com/immo641 Polaris hereby declares that the Connectivity Control Unit "CCU‑2" wireless system conforms with the rele- vant guidelines.

  • Page 158: Country-Specific Declarations Of Conformity (Ccu-2)

    24 DECLARATIONS OF CONFORMITY 24.3 Country-specific declarations of conformity (CCU‑2) E02299-01...

  • Page 159: Substances 25

    SUBSTANCES 25 Brake fluid DOT 4 / DOT 5.1 Standard/classification – Guideline – Use only brake fluid that complies with the specified standard (see specifications on the container) and that exhibits the corresponding properties. Recommended supplier Castrol – REACT PERFORMANCE DOT 4 ®...
  • Page 160 25 SUBSTANCES Fork oil (SAE 5) Standard/classification – SAE ( p. 160) (SAE 5) Guideline – Use only oils that comply with the specified standards (see specifications on the container) and that pos- sess the corresponding properties. Recommended supplier MOTOREX ®...

  • Page 161: Auxiliary Substances 26

    AUXILIARY SUBSTANCES 26 Chain cleaner Recommended supplier ® MOTOREX – Chain Clean Fuel additive Recommended supplier ® MOTOREX – Fuel Stabilizer Long-life grease Recommended supplier ® MOTOREX – Bike Grease 2000 Motorcycle cleaner Recommended supplier ® MOTOREX – Moto Clean Perfect finish and high gloss polish for paints Recommended supplier ®...

  • Page 162: Standards

    27 STANDARDS JASO T903 MA2 Different technical development directions required a separate specification for motorcycles – the JASO T903 MA2 standard. Earlier, engine oils from the automobile industry were used for motorcycles because there was no separate motorcycle specification. Whereas long service intervals are demanded for automobile engines, the focus for motorcycle engines is on high performance at high engine speeds.

  • Page 163: Index Of Special Terms 28

    Auxiliary function of the motor control that reduces engine torque with spinning rear wheel On-board diagnosis Vehicle system, which monitors the specified param- eters of the vehicle electronics Ride Husqvarna System for wireless communication with appropriate cellphones and headsets for telephony and audio...

  • Page 164: List Of Abbreviations

    29 LIST OF ABBREVIATIONS Art. no. Article number circa compare e.g. for example etc. et cetera i.a. inter alia number poss. possibly...

  • Page 165: List Of Symbols 30

    This is also shown in the display. The malfunction indicator lamp lights up yellow – The OBD has detected a malfunction in the vehicle electronics. Come safely to a halt, and contact an authorized Husqvarna Motor- cycles workshop.

  • Page 166: Index

    ......84 Ride Husqvarna (optional) ... . . 47 checking for dirt .
  • Page 167 INDEX Rider' Headset (optional) ....49 Engine sprocket seat heating (optional) ....37 checking .
  • Page 168 INDEX Passenger seat mounting ......81 Grab handles ......25 removing .
  • Page 169 INDEX Socket for electrical accessories ..21 Towing ......72 Spare parts .
  • Page 170 *3402576en* 3402576en 12/2021 Husqvarna Motorcycles GmbH Stallhofnerstraße 3 5230 Mattighofen Austria Photo: Mitterbauer/KISKA, www.husqvarna-motorcycles.com Husqvarna Motorcycles GmbH...

Table of Contents