Advertisement
Available languages
Available languages
FAN button
• Pressing this button can select fan speed as: AUTO, SPEED 1 (
2 (
), SPEED 3 (
).
NOTE:
ū Under Auto speed, air conditioner will select proper fan speed
automatically according to ambient temperature.
ū Fan speed can't be adjusted under dry mode.
X-FAN button
• Press this button under cool and dry mode to start up x-fan function.
Press this button again to cancel X-FAN function.
• Under Auto speed, air conditioner will select proper fan speed
automatically according to ambient temperature.
• Fan speed can't be adjusted under dry mode.
• When X-FAN function is on, if the air conditioner is turned off, fan will
still operate at low speed for a while to blow the residual water inside
the air duct.
• During X-FAN operation, press X-FAN button to turn off X-FAN function.
Indoor fan will stop operation immediately.
SLEEP button
• Press sleep button to enter into sleep mode. If the controller operates
at cooling mode, after sleep mode is started up, preset temperature will
increase by 1 °C within 1 hour; preset temperature will increase by 2 °C
within 2 hours and then the unit will operate at this temperature until
turned off.
• Sleep function is only available for cooling mode. SLEEP function can be
set together with OFF timer.
TIMER button
• When unit is on, press this button to set Timer Off. T-OFF and H icon
will blink. Within 5s, press + or - button to adjust the time for Timer
Off. Pressing + or - button once will increase or decrease the time by
0.5 hours. Hold + or - button for 2 seconds, time will change quickly.
Release the button after your required set time is reached. Then press
TIMER button to confirm it. T-OFF and H icon will stop blinking.
• When unit is off, press this button to set Timer On. T-ON and H icon will
be blinking. Within 5 seconds, press + or - button to adjust the time for
Timer On. Pressing + or - button once will increase or decrease the time
by 0.5 hours. Hold + or - button for 2 seconds, time will change quickly.
Release the button after your required set time is reached. Then press
TIMER button to confirm it. T-ON and H icon will stop blinking.
• Canceling the timer function: If Timer function is set up, press TIMER
button once to review the remaining time. Within 5 seconds, press
TIMER button again to cancel this function.
• ON timer and OFF timer cannot be set together.
NOTE:
ū Range of time setting is: 0.5~24 hours.
ū The interval between two motions can't exceed 5 seconds, otherwise the
remote control will exit setting status.
Functions by Combination Buttons
Child lock function
Press "+" and "-" buttons simultaneously can turn on or turn off child lock
function. When child lock function is started up, child lock indicator on
remote controller is ON. If you operate the remote control, remote control
won't send signal.
This function works only for remote controller, the buttons on the unit
itself can not be locked.
Temperature display switchover function
Under OFF status, press "-" button and "MODE" button simultaneously can
switch between °C and °F.
Light function
You can turn off or turn on the light of the unit's control panel. Under
switch-on or switch-off status, point the remote control to the unit's signal
receiver and you may hold "+" and "FAN" buttons simultaneously for 3
), SPEED
seconds to set the light on or off.
Installation of batteries
1. Press and slide the back cover to open the battery compartment of the
remote control.
2. Insert two AAA (1,5 V) size batteries (included). Make sure the (+) and
(–) ends of the batteries match the (+) and (–) ends indicated in the
battery compartment.
3. Close the battery compartment cover.
NOTE:
ū During operation, point the remote control signal sender at the receiving
window on indoor unit.
ū The distance between signal sender and receiving window should be no
more than 8 meters, and there should be no obstacles between them.
ū Signal may be interfered easily in the room where there is fluorescent
lighting or wireless telephone; in these situations, move the remote
control closer to the appliance for reliable operation.
ū Replace new batteries of the same model when replacement is required.
ū If you will not be using the unit for a long time, remove the batteries
from the remote control.
ū If the display on remote control is fuzzy or there's no display, please
replace batteries.
Care and Maintenance
WARNING!
• Before cleaning the air conditioner, please turn off the unit and disconnect
power. This will ensure that the risk of an electric shock is eliminated.
• Do not wash air conditioner with water. This will ensure that the risk of an
electric shock is eliminated.
• Do not use volatile liquid (such as thinner or gas) to clean the air conditioner.
Otherwise, it may damage the surface.
• Do not use liquid or corrosive detergent clean the appliance and do not
splash water or other liquid onto it, otherwise,it may damage the plastic
components, or even cause electric shock.
Clean outer case and grille
Clean outer case:
If there's dust on the surface of outer case, please use soft cloth to wipe it.
If the outer case is very dirty (such as grease), please use neutral detergent
to wipe it.
Clean grille:
To clean the grille itself, use a soft brush.
Clean filter
(Do not touch the fins to prevent injury.)
1. Remove the filter
Press the clasp as shown in the figure, and then remove the filter;
EN
Advertisement
