Related Manuals for Taylor C723
Summary of Contents for Taylor C723
- Page 1 OPERATOR’S MANUAL Model C723 Soft Serve Freezer Original Operating Instructions 3/18/11 (Original Publication) 069127-M (Updated 8/20/2020)
- Page 2 Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions. © March 2011 Taylor Company (Updated 8/20/2020) 069127-M Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be...
-
Page 3: Table Of Contents
Refrigerant ........................1-4 Section 2: To the Operator Section 3: Safety Section 4: Operator Parts Identification Model C723.........................4-1 Model C723 - Factory Equipped With Agitator............4-3 Model C723 - Door and Beater Assembly..............4-5 Optional Carts ......................4-6 Accessories.........................4-7 Brushes ........................4-8 Section 5: User Interface Model C723.........................5-1... - Page 4 Table of Contents Section 7: Operator Checklist During Cleaning and Sanitizing .................. 7-1 Troubleshooting Bacterial Count ................7-1 Regular Maintenance Checks..................7-1 Winter Storage......................7-2 Section 8: Troubleshooting Guide Section 9: Parts Replacement Schedule Section 10: Limited Warranty on Equipment Section 11: Limited Warranty on Parts 069127-M...
-
Page 5: Section 1: To The Installer
6 in. (152 mm) on the left and right sides and 0 in. on • Authorized service personnel should consult the back. The Model C723 equipped with top air OSHA Standard 29CFRI910.147 or the discharge requires 6 in. (152 mm) on the left side, 0 in. -
Page 6: Water Connections
• DO NOT operate the machine unless it is properly grounded. • DO NOT operate the machine with fuses larger than specified on the machine's data label. • All repairs should be performed by an To the Installer Model C723... -
Page 7: Beater Rotation
It is recommended that beater rotation adjustment be • Stationary machines that are not equipped with performed by a Taylor service technician. a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with Optional Carts a contact gap of at least 0.125 in. -
Page 8: Refrigerant
TO THE INSTALLER Refrigerant NOTICE! Taylor reminds technicians to be CAUTION! This machine contains fluorinated aware of government laws regarding refrigerant recovery, greenhouse gases (F-Gas) to provide refrigeration using recycling, and reclaiming systems. If you have any a hermetically sealed circuit or within foam insulation. -
Page 9: Section 2: To The Operator
If you should require technical assistance, please contact your local authorized Taylor distributor. Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor distributor, and only if all required service work is provided by an authorized Taylor service technician. - Page 10 TO THE OPERATOR Compressor Warranty Disclaimer It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the The refrigeration compressor(s) on this machine are refrigerant is lost during the course of ordinary service to...
-
Page 11: Section 3: Safety
Safety Section 3 We at Taylor Company are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to IMPORTANT! This machine is provided with an protect both operators and service technicians. - Page 12 WARNING! Only install this machine in a Failure to follow these instructions may result in location where its use and maintenance is restricted to electrocution. Contact your local authorized Taylor trained personnel. Failure to comply may result in distributor for service.
- Page 13 Do not obstruct air intake and discharge openings: 39 in. (1.0 m) from the surface of the machine and at a The Model C723 air-cooled requires a minimum of height of 63 in. (1.6 m) from the floor.
- Page 14 SAFETY Notes: Safety Model C723...
-
Page 15: Section 4: Operator Parts Identification
Operator Parts Identification Section 4 Model C723 Figure 4-1 Operator Parts Identification Model C723... - Page 16 OPERATOR PARTS IDENTIFICATION Model C723 Exploded View Parts Identification Item Description Part No. Item Description Part No. Cover-Hopper 041682-BLA Screw-1/4-20X3/8 SLTD 011694 Orifice 022465-100 Screw-Wing Head 081582 O-ring-3/8 OD X .070W 016137 Tray-Drip 080781 (100 to Bag) Shield-Splash-Wire 046177-SP Tube A.-Feed-SS-5/32 Hole...
-
Page 17: Model C723 - Factory Equipped With Agitator
OPERATOR PARTS IDENTIFICATION Model C723 - Factory Equipped With Agitator Figure 4-2 Operator Parts Identification Model C723... - Page 18 OPERATOR PARTS IDENTIFICATION Model C723 Factory Equipped with Agitator Exploded View Parts Identification Item Description Part No. Item Description Part No Cover-Hopper-14 Qt-Gray 041682-GRY Screw-1/4-20X3/8 SLTD 011694 Orifice 022465-100 Screw-Wing Head 081582 O-ring-3/8 OD X .070W 016137-SER Tray-Drip 080781...
-
Page 19: Model C723 - Door And Beater Assembly
OPERATOR PARTS IDENTIFICATION Model C723 - Door and Beater Assembly Figure 4-3 Item Description Part No. Item Description Part No. Plug-Prime Twin 059936 Cap-Design 1.010"ID-6 Point 014218 O-ring-1/2OD X .070W (50 to Bag) 024278 Seal-Draw Valve-Large H-ring 034698 Gasket-Door HT 4"-Double 048926 Valve A.-Draw-Center... -
Page 20: Optional Carts
Caster-3" SWV 3/4-10 Stem 030307 Caster-3" SWV 3/4-10 Stem 021279 w/Brake Note: ADA-compliant height cart, not equipped with a door. Panel-Side-STD Cart 069428 Panel-Rear-STD Cart 069429 Note: Standard height cart with reversible front door panel and rear panel. Operator Parts Identification Model C723... -
Page 21: Accessories
OPERATOR PARTS IDENTIFICATION Accessories Apply the appropriate Taylor approved food safe lubricant. Figure 4-5 Item Description Part No. Item Description Part No. Lubricant-Taylor 4 oz. 047518 Pail-10 qt 013163 Tool-O-ring Removal 048260-WHT Kit A.-Tune-Up X49463-80 *A sample container of sanitizer is sent with the machine. For ®... -
Page 22: Brushes
OPERATOR PARTS IDENTIFICATION Brushes Figure 4-6 Item Description Part No. Item Description Part No. Black Bristle Brush 013071 White Bristle Brush (1” x 2”) 013073 Double End Brush 013072 White Bristle Brush (3” x 7”) 023316 Operator Parts Identification Model C723... -
Page 23: Model C723
User Interface Section 5 Model C723 Figure 5-1 Item Description Item Description Power Switch Select Key Liquid Crystal Display Service Menu Key Keypads Brush-Clean Counter Mix Out Indicator Arrow Keys Standby Key Syrup Heater Key (Inactive) Mix Low Indicator Decal-rear Mix Lights... -
Page 24: Symbol Definitions
To better communicate in the international arena, = Standby symbols have replaced words on many of our operator switches, function, and fault indicators. Your Taylor machine is designed with these international symbols. The following chart identifies the symbol definitions. = Topping Heater... - Page 25 Important! Make sure the level of mix in the hopper is down again, contact your service technician. below the mix delivery hole in the feed tube. Failure to follow this instruction may result in lower product quality when normal operation is resumed. User Interface Model C723...
- Page 26 Important! Make sure the level of mix in the hopper is below the mix inlet hole in the feed tube. Failure to follow this instruction may result in lower product quality when normal operation is resumed. Figure 5-5 User Interface Model C723...
-
Page 27: Operating Screen Descriptions
After hour 99, it will change to a letter and failure. a number (example: A0, A1, B0, B1, etc.). User Interface Model C723... -
Page 28: Manager's Menu
(See Figure 5-12.) The SERVINGS COUNTER screen is used to reset the servings counter to zero. The SERVINGS COUNTER automatically resets to zero when the machine is brush-cleaned. (See Figure 5-13.) User Interface Model C723... - Page 29 Press the Up or Down arrow to move to the appropriate month for the start of DST. (See SET CLOCK Figure 5-20.) 12:01 2/10/2011 Change > Exit DST START MONTH > Figure 5-16 Figure 5-20 User Interface Model C723...
- Page 30 The Standby option is used to manually place either side of the machine in the Standby mode during long no draw periods. Select the Standby screen from the menu. Press the SEL symbol to activate Standby. User Interface Model C723...
- Page 31 Menu. Press the Menu symbol to return to the Manager's temperature in the hopper was above 45°F (7°C) more Menu. than 1 hour. L - R BRL>45F (7C) AFTER 1 HR—The mix temperature in the freezing cylinder was above 45°F (7°C) more than 1 hour. User Interface Model C723...
- Page 32 (See Figure 5-32.) Figure 5-36 Use the arrow symbols to move the arrow. Pressing the SOFTWARE VERSION C723 CONTROL UVC4 SEL symbol with the arrow next to No will return to the VERSION V00.00.000 Manager's Menu. Pressing the SEL symbol with the >...
-
Page 33: Section 6: Operating Procedures
Operating Procedures Section 6 The Model C723 is a medium-capacity soft serve 11470 machine. Mix is stored in the hoppers. The mix flows by gravity through a feed tube into the freezing cylinders. The machine is equipped with a three-spout door and two Apply the appropriate 2.8 qt. - Page 34 Do not lubricate the gaskets or bearings. 13. Slide the two O-rings into the grooves on each prime plug. Apply an even coat of Taylor Lube to the O-rings and shafts. 11468 Apply the appropriate Taylor approved food safe lubricant.
- Page 35 Lubricate the 10518 H-ring and O-rings. 101551 Apply the appropriate Taylor approved food safe lubricant. Figure 6-7 Figure 6-10 15. To install the freezer door, insert the baffle rods through the beaters in the freezing cylinders.
- Page 36 5 oz to 7-1/2 oz (148 ml to 222 ml) of product by weight per 10 seconds. 22. To increase the flow rate, turn the adjustment screw clockwise. Turn the adjustment screw counterclockwise to decrease the flow rate. Figure 6-17 Operating Procedures Model C723...
-
Page 37: Sanitizing
Figure 6-21 Note: You have just sanitized the mix hopper and parts. Therefore, make sure your hands are clean and sanitized before proceeding to the next step. Operating Procedures Model C723... -
Page 38: Priming
2. Open the draw valve to remove the sanitizing solution. When only fresh mix is flowing, close the draw valve. Figure 6-23 9. With an empty pail beneath the door spouts, raise the prime plug. Operating Procedures Model C723... -
Page 39: Closing Procedure
Closing Procedure These procedures must be performed daily. 4. Repeat these steps for the other side of the machine. ALWAYS FOLLOW LOCAL HEALTH CODES. To disassemble the Model C723, the following items will be needed: • Two cleaning and sanitizing pails •... -
Page 40: Rinsing
4. Repeat this procedure using clean, warm water until the water being discharged is clear. 8. Repeat these steps on the other side of the machine. 5. Repeat these steps for the other side of the machine. Operating Procedures Model C723... -
Page 41: Disassembly
O-ring(s) should be replaced or properly lubricated. Figure 6-28 5. Repeat these steps on the other side of the machine. 6. Wipe all exterior surfaces of the freezer with a clean, sanitized towel. Operating Procedures Model C723... - Page 42 OPERATING PROCEDURES Notes: 6-10 Operating Procedures Model C723...
-
Page 43: Section 7: Operator Checklist
Use the black bristle brush to thoroughly clean the rear shell bearing at the rear of the freezing Follow all lubricating procedures as outlined in cylinder. Use a generous amount of cleaning “Assembly.” solution on the brush. Operator Checklist Model C723... -
Page 44: Winter Storage
Failure to follow severe and costly damage to the refrigeration system. this instruction may result in electrocution. Your local Taylor distributor can perform this winter storage service for you. If your machine is water-cooled, check the water Wrap detachable parts of the freezer such as dasher, lines for kinks or leaks. -
Page 45: Section 8: Troubleshooting Guide
8. Excessive mix leakage from a. Bottom O-ring on draw valve is a. Lubricate properly or replace the O-ring. the bottom of door spout. improperly lubricated is or worn. Troubleshooting Guide Model C723... - Page 46 13.No control panel functions a. Machine is unplugged. a. Plug into wall receptacle. - - - with power switch ON. b. Circuit breaker OFF or blown fuse. b. Turn the breaker ON or replace the - - - fuse. Troubleshooting Guide Model C723...
- Page 47 Inspect and replace if Minimum necessary. White Bristle Brush, 1” x 2” Inspect and replace if Minimum necessary. Black Bristle Brush, 1” x 2” Inspect and replace if Minimum necessary. Double-Ended Brush Inspect and replace if Minimum necessary. Parts Replacement Schedule Model C723...
- Page 48 PARTS REPLACEMENT SCHEDULE Notes: Parts Replacement Schedule Model C723...
-
Page 49: Section 10: Limited Warranty On Equipment
LIMITED WARRANTY Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or remanufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part. - Page 50 7. Failure, damage, or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration, or improper operation or use as indicated in the Taylor Operator's Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.
- Page 51 LEGAL REMEDIES The owner must notify Taylor in writing by certified or registered letter to the following address,of any defect or complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
- Page 52 LIMITED WARRANTY ON EQUIPMENT Notes: 10-4 Limited Warranty on Equipment Model C723...
-
Page 53: Section 11: Limited Warranty On Parts
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or remanufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part. - Page 54 Taylor. 5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator's Manual, as well as any release sheets and clips for the Product's upper platen assembly.
- Page 55 LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
- Page 56 LIMITED WARRANTY ON PARTS Notes: 11-4 Limited Warranty on Parts Model C723...
Need help?
Do you have a question about the C723 and is the answer not in the manual?
Questions and answers