Telit Wireless Solutions E922-3GR Series User Manual
  1. Manuals
  2. Brands
  3. Telit Wireless Solutions Manuals
  4. Computer Hardware
  5. E922-3GR Series
  6. User manual
Telit Wireless Solutions E922-3GR Series User Manual

Telit Wireless Solutions E922-3GR Series User Manual

Interface board hw
Hide thumbs Also See for E922-3GR Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Interface Board HW User Guide
xE922-3GR
1VV0301285 Rev.0.3 – 2017-01-12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E922-3GR Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Telit Wireless Solutions E922-3GR Series

Summary of Contents for Telit Wireless Solutions E922-3GR Series

  • Page 1 Interface Board HW User Guide xE922-3GR 1VV0301285 Rev.0.3 – 2017-01-12...
  • Page 2 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 APPLICABILITY TABLE PRODUCT HE922-3GR WE922-3GR Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 2 of 39 Mod. 0805 2015-02 Rev.4...
  • Page 3 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Notice While reasonable efforts have been made to assure the accuracy of this document, Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein.
  • Page 4 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Usage and Disclosure Restrictions License Agreements The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement.

  • Page 5: Table Of Contents

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Table of Contents 1. Introduction ........................7 1.1. Scope ........................7 1.2. Related Documents ....................7 1.3. Abbreviations ......................7 2. General description ...................... 8 2.1. IFBD view ......................... 9 3. Component Assembly Diagram ................10 4.
  • Page 6 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Table of Figures Figure 1 xE922-3GR IFBD Top View ......................... 9 Figure 2 xE922-3GR IFBD Bottom View ......................9 Figure 3 component Assembly Top (Top View) ....................10 Figure 4 component Assembly Bottom (Bottom View) ..................11 List is Tables Table 1 JM1 ...............................

  • Page 7: Introduction

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Introduction 1.1. Scope The scope of this document is to describe the xE922-3GR Interface Board which is part of the complete xE922-3GR Development Kit (Dev-Kit) 1.2. Related Documents Doc # Document Name 1VV0301272 xE922-3GR Hardware User Guide 1VV0301249...

  • Page 8: General Description

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 General description The Interface Board (IFBD) is custom designed to interface the Telit module variant xE922-3GR with the Telit Generic Evaluation Board (EVB) thus forming the complete Development Kit of xE922-3GR The IFBD provides the mapping of Telit module signals and functions into the generic EVB signals and functions The xE922-3GR IFBD design includes the following items:...

  • Page 9: Ifbd View

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 2.1. IFBD view The below pictures show the IFBD Top and bottom view Figure 1 xE922-3GR IFBD Top View Figure 2 xE922-3GR IFBD Bottom View Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 9 of 39 Mod.

  • Page 10: Component Assembly Diagram

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Component Assembly Diagram Figure 3 component Assembly Top (Top View) Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 10 of 39 Mod. 0805 2015-02 Rev.4...
  • Page 11 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Figure 4 component Assembly Bottom (Bottom View) Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 11 of 39 Mod. 0805 2015-02 Rev.4...

  • Page 12: 0-Pin Male B2B Connectors

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 120-Pin male B2B connectors The interface between IFBD and EVB is implemented via 3pcs of 120p (20p x 6 rows) SAMTEC SEARAY 1.27mm High Speed/High Density B2B connectors (10mm stacking height SEAM/SEAF). The following tables describe the IFBD B2B connector pin naming.
  • Page 13 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Table 2 JM2 GPS_LNA_BIAS GPIO54_EINT1 VMIC_BIAS MICP2 MICN2 HP_OUT_R MICP1 MICN1 EP_N HP_OUT_L SPKR_LN SPKR_LP VAUX_3P0V MIC_VDD DIG_MIC_CLK DIG_MIC_D1 CHG_POK_IN CHG_RST_OUT ADC_IN1 ADC_IN0 FG_IBATP FG_IBATN GPIO55_EIN15 VSIM1 VSIM1 SIMCLK1 USIM1_DETECT SIMIO1 SIMRST1 HW_KEY V_RTC...
  • Page 14 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Table 3 JM3 V_BAT V_BAT V_BAT V_BAT_PA V_BAT_PA V_BAT_PA V_BAT V_BAT V_BAT V_BAT_PA V_BAT_PA V_BAT_PA V_BAT_PA V_BAT_PA V_BAT_PA V_BAT_PA V_BAT_PA V_BAT_PA VBUS_PWR_EN GPIO49 GPIO48 DSI_CLKP DSI_CLKN DSI_DP3 DSI_DN3 DSI_DP2 DSI_DN2 GPIO46 GPIO5_EINT7 GPIO1_EINT2 DSI_DP1...

  • Page 15: Module To Evb Signal Mapping

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Module to EVB Signal Mapping The below table introduces the mapping of xE922-3GR module pins and functions into the generic EVB Pin-List and functionality In many cases the signal names are changed across the platform as many of the EVB signals are simply used as “pipes”...
  • Page 16 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Pin # IFBD Connector Pin Generic EVB Pin Name xE922-3GR Pad Description Name PCIE_RX_P USB_SS_TX_P PCIE_TX_P PCIE_RX_M USB_SS_TX_M CAM_MCLK TGPIO_12 Camera MCLK output USIF1_TXD SPI_MOSI UART1 TXD / SPI1 Serial data Output PCIE_TX_M GPIO47 TGPIO_11...
  • Page 17 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Pin # IFBD Connector Pin Generic EVB Pin Name xE922-3GR Pad Description Name CSI2_DN CSI2_D0_N Sub Camera CSI Data Input Negative CAM2_RESET TGPIO_21 Sub Camera Reset / GPIO CAM2_PD TGPIO_10 Sub Camera Power Down / GPIO GPIO7 TGPIO_22 Reserved for internal HE/WE922...
  • Page 18 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Pin # IFBD Connector Pin Generic EVB Pin Name xE922-3GR Pad Description Name SDIO_DAT2 WIFI_SD2_TGPIO17 SDIO2 SDIO_DAT3 WIFI_SD3_TGPIO18 SDIO3 CAM1_RESET WIFI_SD4_TGPIO23 Main Camera Reset / GPIO USIF2_RXD RX_AUX UART2 RXD / SPI2 Serial data input CSI1_DN1 CSI1_D1_N Main Camera CSI Data1 Input...
  • Page 19 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Table 5 JM2 Connector IFBD Connector Pin Generic EVB Pin xE922-3GR Description Name Name GPS LNA BIAS coming from EVB Main GPS_LNA_BIAS GPS_LNA_BIAS Board GPIO54_EINT1 GPS_LNA_EN GPIO / External IRQ VMIC_BIAS MICBIAS AJ18 Analog Microphone bias...
  • Page 20 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Connector Pin Generic EVB Pin xE922-3GR Description Name Name HP Left for 3.5mm jack or EP_P for dif HP_OUT_L/EP_P EAR1_MT+ AL20/AK21 mode SPKR_LN AF21 Speaker Signal Out Negative SPKR_LP AH21 Speaker Signal Out Positive VAUX_3P0V Auxiliary 3.0V power supply (from eMMC)
  • Page 21 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Connector Pin Generic EVB Pin xE922-3GR Description Name Name DVI_RX DVI_TX DVI_CLK DVI_WAO GPIO55_EINT15 REF_CLK GPIO / External IRQ eSIM_RST External SIM signal 1 – Power supply for VSIM1 SIMVCC1 the SIM External SIM signal 1 –...
  • Page 22 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Connector Pin Generic EVB Pin xE922-3GR Description Name Name VBUS_DET USB_VBUS External IRQ, Used for SoC VBUS detection USB_ID USB_ID USB_ID, USB OTG use External SIM signal 2 – Card detect (Active USIM2_DETECT SIMIN2 AR10...
  • Page 23 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Table 6 JM3 Connector IFBD Connector Pin xE922-3GR Pin # Generic EVB Pin Name Description Name V_BAT_1 VBATT AR18 Main power supply for Baseband V_BAT_2 VBATT AS19 Main power supply for Baseband V_BAT_3 VBATT AR20...
  • Page 24 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Connector Pin xE922-3GR Pin # Generic EVB Pin Name Description Name Enable External VBUS source for VBUS_PWR_EN AW17 GPIO49 GPIO / MIPI Trace Data 5 GPIO48 GPIO / MIPI Trace Data 4 DSI_CLKP DSI_CLK_P LCD DSI Clock Positive...
  • Page 25 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Connector Pin xE922-3GR Pin # Generic EVB Pin Name Description Name Thermal sensor on IFBD, Read by D8_THERM_ASTAR D8_THERM_ASTAR Arduino on EVB GPIO73_EINT10 GPIO / External IRQ GPIO72_EINT9 GPIO / External IRQ GPIO67_EINT0 GPIO / External IRQ GPIO66_EINT15...
  • Page 26 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Connector Pin xE922-3GR Pin # Generic EVB Pin Name Description Name LCD_TE GPS_PPS LCD Tearing effect input GPIO58_EINT2 GPS_RFPAON GPIO / External IRQ GPIO63_EINT8 GPS_CLK GPIO / External IRQ JTAG_TDI JTAG_TDI JTAG DIG_MIC_D2...

  • Page 27: Ifbd Sub-Circuitry / Stuffing Options

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 IFBD Sub-Circuitry / Stuffing Options This section provides the description of circuits which were designed into the IFBD in order to serve as an interface between EVB main board and the xE922-3GR module These items are specific to the xE922-3GR module thus are not part of the generic EVB main board 6.1.

  • Page 28: Adc_Vbatmeas

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.2. ADC_VBATMEAS As explained in the xE922-3GR HW user guide, in case that external charger IC solution is not applied, there is still the requirement to connect ADC_VBATMEAS to the V_BAT supply input (R30 stuffed / R31 not stuffed = default).

  • Page 29: Analog Audio Output

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.3. Analog audio output xE922-3GR has two options to provide Analog audio output to the 3.5mm headset connector on the EVB main Board:  Single ended stereo : R16 not stuffed / R17 stuffed ( default) o In that case it is recommended to use the Stereo Jack on EVB ...

  • Page 30: Power On_Off / Reset

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.4. POWER ON_OFF / RESET The EVB main board provides in a push button PWR_PB, when asserted active LOW polarisation. In order to comply with the active HIGH polarity of xE922-3GR system, the transistor Q1 inverts the signal. As also explained in the xE922-3GR HW user guide, when the system is supplied with V_BAT for the first time, it will automatically start up without waiting for a start-up event.

  • Page 31: Usb

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.5. As explained in the xE922-3GR HW user guide, for proper DRD / OTG operation, USB_ID and GPIO1_EINT2 should be connected together, R38. 6.6. CAM_I2C Starting from xE922-3GR revision CS1772B, the CAM_I2C signals will no longer have an internal pullup resistors to VAUX_1P8V.

  • Page 32: Usim

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.7. USIM Starting from xE922-3GR revision CS1772B, internal pullups will be foreseen on the SIMIO lines (R43/R44 will become obsolete). For proper SIM card detection (active LOW, external pullup resistors are required (R41/R42). 6.8.

  • Page 33: Jtag / Mipi Connector

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.9. JTAG / MIPI connector The EVB main board has a standard 20p box header used for JTAG interfacing. In-order to better match the JTAG tools (JTAG Pod) used for xE922-3GR, an additional JTAG connector (J1) was added to IFBD.

  • Page 34: Rf Connectors

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 6.10. RF connectors The xE922-3GR system can work with a passive GNSS antenna. (Internal LNA available on the module) For active GNSS antenna application, a dedicated 3.0V regulator which resides on the EVB main board can be enabled for suppling the external antenna LNA via GPS_LNA_BIAS line.

  • Page 35: Schematics

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Schematics Searchable PDF CS1777A-A.pdf CS1777A-B.pdf Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 35 of 39 Mod. 0805 2015-02 Rev.4...
  • Page 36 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 36 of 39 Mod. 0805 2015-02 Rev.4...
  • Page 37 Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 37 of 39 Mod. 0805 2015-02 Rev.4...

  • Page 38: Safety Recommendations

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Safety Recommendations READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: ...

  • Page 39: Document History

    Interface Board HW User Guide 1VV0301285 Rev.0.3 – 2017-01-12 Document History Revision Date Changes 2016-05-26 First draft for review 2016-08-24 Updated naming Updates related to CS1772B 2017-01-12 Update stuff options in screenshots Update on GPIO7 reserved function (ch 5 table 4) Reproduction forbidden without written authorization from Telit Communications S.p.A.

This manual is also suitable for:

He922-3grWe922-3gr

Table of Contents