Table of Contents
Advertisement
Quick Links
ITV1000/2000/3000/2090-52* Series
ITV1000/2000/3000/2090-53* Series
● Install and operate the product only after reading the Operation Manual carefully and
understanding its contents.
● Specifically, read the safety instructions carefully.
● Keep this operation manual available whenever necessary.
P R O D U C T
E/P Regulator
(16points preset input type)
MODEL/ Series/ Product Number
(Switch output: NPN output)
(Switch output: PNP output)
Doc. No. ITV2-OM00109-C
N A M E
Advertisement
Table of Contents
Related Manuals for SMC Networks ITV1000-52 Series
Summary of Contents for SMC Networks ITV1000-52 Series
- Page 1 Doc. No. ITV2-OM00109-C P R O D U C T N A M E E/P Regulator (16points preset input type) MODEL/ Series/ Product Number ITV1000/2000/3000/2090-52* Series (Switch output: NPN output) ITV1000/2000/3000/2090-53* Series (Switch output: PNP output) ● Install and operate the product only after reading the Operation Manual carefully and understanding its contents.
-
Page 2: Table Of Contents
Contents Contents Safety Instructions Handling precautions Wiring method Relation of input signal and preset pressure Setting method Key locking function Setting of min. pressure, max. pressure and preset pressure Auto memory function Switch output (Out of range mode) Error indicating function Detail setting mode Gain setting Sensitivity setting... -
Page 3: Safety Instructions P2
E/P Regulator Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) and other safety regulations. ... - Page 4 E/P Regulator Safety Instructions Caution 1. The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. ...
-
Page 5: Handling Precautions P4
Handling precautions △ Caution ！ If the power supply to this product is turned off due to a power failure during normal operation, the output on the secondary side will be held and air will flow continuously. If supply pressure to this product is interrupted or shut off, while the power is still on, the internal solenoid valve will continue to operate and a humming noise will be generated. - Page 6 △ Caution ！ Take the following steps to avoid malfunction due to noise. 1. Install a line filter etc. to the AC power line to reduce / eliminate power supply noise. 2. Avoid malfunction due to noise by installing this product and its wiring away from strong electric fields, such as those of motors and power cables, etc.
-
Page 7: Wiring Method P6
Wiring method △ Caution ！ ① Proceed carefully, as incorrect wiring can cause damage. ② Use a DC power supply with sufficient capacity and a low ripple. ③ Turn off the power supply to remove and insert the connector. ④ Never rotate the right angled type connector as it is not designed to rotate. -
Page 8: Relation Of Input Signal And Preset Pressure P8
Wiring diagram (Input signal） 1：Brown 2：White 3：Blue 4：Black Power supply DC24V+/-10% 5：Gray Power supply Note: Common is no polarity. The power supply can connect the direction of the plus or minus either. Relation of Input signal and preset pressure Preset Input signal 4 Input signal 3... -
Page 9: Setting Method P8
Setting method △ Caution ！ ① If an incorrect key is pressed or incorrect information is displayed during setting, power must be turned off and the procedure started again. ② It is recommended that the settings are changed without supply pressure. The product operates immediately after preset pressures are set and the S-key is pressed. -
Page 10: Key Locking Function P9
Key locking function △ Caution ！ The keys are locked after turning the power on and can not be operated. Unlocking the keys Key operation LED Display (current) pressure is displayed ① ② Press ▽ key for 2 seconds or more. is displayed flashes on the display ③ ... -
Page 12: Switch Output (Out Of Range Mode) P11
Switch output (Out of range mode) The switch output turns on when output pressure is achieved to +/-5%F.S. of setting oressure. Input Signal Output pressure of E/P regulator ON Switch output OFF Error Indicating function Error name Contents of error Countermeasure display Please execute "Initialize (refer to... -
Page 13: Detail Setting Mode P12
Detail setting mode Key operation and LED display Unlock keys (refer to P9) ① Press S-key for 2 seconds or more. ② (displayed alternately) ⇔ △key ↑ Press S-key ↓ ... -
Page 14: Sensitivity Setting P13
Set the GAIN by using the △ and▽ keys. ⑤ (blink and change the most right digit) Press S-key. (displayed alternately) ⑥ ⇔ Press S-key for 2 seconds or more, then go out from detail setting mode. ⑦ (Select the menu with △ or ▽ keys, then jump to another item.) Lock keys (refer to P9) ⑧... -
Page 15: Zero Clear P14
Zero clear The display can be reset to zero by executing "Zero clear". When "Zero clear" is executed with residual pressure in the secondary piping, the pressure is assumed to be zero. Please execute the operation of "Zero clear" with the supply pressure interrupted, and the piping of the secondary side removed. -
Page 16: Led Display P15
Press △ and ▽ keys for 3 seconds or more. ⑤ is displayed (press S-key to ③) "Initialize" is executed, after 5 seconds. Turning off for 1 second ⑥ (Release keys till less than 5 seconds to ④) Returns to the state immediately after turning on the power supply. ⑦ ...
Need help?
Do you have a question about the ITV1000-52 Series and is the answer not in the manual?
Questions and answers