Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vents VUT 100 P mini
Summary of Contents for Vents VUT 100 P mini
- Page 1 USER’S MANUAL VUT 100 P mini VUE 100 P mini Air handling unit...
-
Page 2: Table Of Contents
Transported air must not contain any dust or other solid impurities, sticky substances, or fibrous materials. Do not use the unit in a hazardous or explosive environment containing spirits, gasoline, insecticides, etc. Do not close or block the intake or extract vents in order to ensure the efficient air flow. www.ventilation-system.com... - Page 3 Do not sit on the unit and do not put objects on it. The information in this user’s manual was correct at the time of the document’s preparation. The Company reserves the right to modify the technical characteristics, design, or configuration of its products at any time in order to incorporate the latest technological developments.
-
Page 4: Purpose
Name Number Air handling unit User's manual Speed switch Packing box DESIGNATION KEY VUT 100 P mini Designation example: Type of ventilation unit VUT– ventilation with heat recovery VUE – ventilation with energy recovery Rated air flow [m3/h] Mounting P - suspended mounting, horizontal spigot orientation Design variant www.ventilation-system.com... -
Page 5: Technical Data
IP22 for the unit connected to the air ducts, IP44 for the unit motors. The unit design is constantly being improved, thus some models may be slightly different from those described in this manual. VUT 100 P mini VUE 100 P mini Speed... -
Page 6: Design And Operating Principle
VUT/VUE 100 P mini DESIGN AND OPERATING PRINCIPLE The unit has the following operating logic: extract air from the room flows into the unit, where it is filtered by the extract filters, then air flows through the heat exchanger and is exhausted outside by the exhaust fan. Air from outside flows into the unit, where it is cleaned by the supply filters. -
Page 7: Mounting And Set-Up
MOUNTING AND SET-UP BEFORE MOUNTING MAKE SURE THE CASING DOES NOT CONTAIN ANY FOREIGN OBJECTS (E.G. FOIL, PAPER). WHILE INSTALLING THE UNIT ENSURE CONVENIENT ACCESS FOR SUBSEQUENT MAINTENANCE AND REPAIR. The unit may be suspended on threaded rods or may be rigidly fixed to a horizontal surface by anchor bolts. Fasteners for fan mounting should be ordered separately. - Page 8 VUT/VUE 100 P mini CONDENSATE DRAINAGE The VUE units are equipped with an enthalpy heat exchanger and do not require condensate drainage. The VUT units are equipped with a drain pan for condensate collection and removal. Temperature differences between supply and extract air flows in heat recovery units lead to condensate formation. Condensate is collected in the drain pan and is removed outside by the drain pipes.
-
Page 9: Connection To Power Mains
CONNECTION TO POWER MAINS POWER OFF THE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT. THE UNIT MUST BE CONNECTED TO POWER SUPPLY BY A QUALIFIED ELECTRICIAN. THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE MANUFACTURER’S LABEL. •... -
Page 10: Technical Maintenance
VUT/VUE 100 P mini TECHNICAL MAINTENANCE DISCONNECT THE UNIT FROM POWER SUPPLY BEFORE ANY MAINTENANCE OPERATIONS! MAKE SURE THE UNIT IS DISCONNECTED FROM POWER MAINS BEFORE REMOVING THE PROTECTION! Maintenance operations of the unit are required 3-4 times per year. They include general cleaning of the unit and the following operations: 1. - Page 11 2. Heat exchanger maintenance (once a year). Some dust may accumulate on the heat exchanger block even in case of regular maintenance of the filters. To maintain the high heat recovery efficiency, regular cleaning is required. Maintenance of the heat exchanger in VUT units: Press out on the latches.
- Page 12 VUT/VUE 100 P mini 3. Fan maintenance (once a year). Even in case of regular maintenance of the filters, some dust may accumulate inside the fans and reduce the fan performance and supply air flow. Clean the fans with a soft brush or cloth. Do not use water, aggressive solvents, or sharp objects as they may damage the impeller.
-
Page 13: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE REASONS TROUBLESHOOTING The fan(s) do(es) not get Make sure the power supply line is connected correctly, No power supply. started. otherwise troubleshoot a connection error. Extract filter clogging. Clean or replace the extract filter. Check the heat exchanger for icing. Switch the unit off Cold supply air. -
Page 14: Manufacturer's Warranty
VUT/VUE 100 P mini MANUFACTURER’S WARRANTY The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. We hereby declare that the product complies with the provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU of the European Parliament and of the Council, Low Voltage Directive (LVD) 2014/35/EU of the European Parliament and of the Council and CE-marking Council Directive 93/68/EEC. -
Page 15: Certificate Of Acceptance
CERTIFICATE OF ACCEPTANCE Unit Type Air handling unit Model Serial Number Manufacture Date Quality Inspector’s Stamp SELLER INFORMATION Seller Address Phone Number E-mail Purchase Date This is to certify acceptance of the complete unit delivery with the user’s manual. The warranty terms are acknowledged and accepted. - Page 16 V59EN-05...
Need help?
Do you have a question about the VUT 100 P mini and is the answer not in the manual?
Questions and answers