Related Manuals for Orlaco CCC
Summary of Contents for Orlaco CCC
- Page 1 Camera CCC, CMOS, AMOS, MILMOS Installation manual No. IM0973060 R2-6 4/2013 English...
- Page 2 If you have any questions or issues concerning the operation of this equipment, consult the relevant section in the manual or contact the Orlaco Products BV Service department. The camera/display systems from Orlaco comply with the latest CE, ADR, EMC and mirror-directive regulations.
-
Page 3: Table Of Contents
Installation manual Contents page 1. Mounting and connecting Camera 1.1. Universal camera bracket 1.2. Camera attachment 1.3. Aiming the camera 1.4. Mounting the standard cable with molded connectors 1.5. Finish 1.6. Camera with solded connectors 1.7. Screw connection 1.8. Tape 1.9. -
Page 4: Mounting And Connecting Camera
Installation manual 1. Mounting and connecting Camera Overhead Horizontal M6 x 20 Overhead Sloping surfaces Horizontal Vertical 1.1. Universal camera bracket. Min. bend radius (R) = 50mm 1000mm Recommendation: The bracket should be Sloping surfaces Vertical a torque of 11 Nm ± 1 Nm (Equal to the p for an M6 bolt. -
Page 5: Aiming The Camera
(R) = 50mm (R) = 50mm Installation manual Recommendation: The bracket should be tig Recommendation: The bracket should be tig Sloping surfaces Sloping surfaces Vertical Vertical a torque of 11 Nm ± 1 Nm (Equal to the pref a torque of 11 Nm ± 1 Nm (Equal to the pref 1.3. -
Page 6: Finish
Installation manual 1.5. Finish. 0,5m M6 x 20 ∅6,5mm Min. bend radius (R) = 50mm Units in mm IM0973060 R2-6... -
Page 7: Camera With Solded Connectors
1000mm Installation manual 1.6. Camera with solded connectors Follow these steps only if a standard 0,5m cable with metal (screw) connector is used. 0,5m 1.7. Screw connection Fill the female coupling ring with vaseline and lock the connection. The Vaseline can be used to protect the screw connection. -
Page 8: Tape
Installation manual 0,5m 1.8. Tape Protect the connection with tape. The tape can be used to insulate (electrical) and isolate (mechanical) the metal connector from metal parts of your vehicle. 0,5m 1.9. Finish. 0,5m 0,5 m M6 x 20 ∅6,5mm Min. -
Page 9: Camera Amos Ir Led Mounting Instructions
Installation manual 1.10. Camera AMOS IR LED mounting instructions The IR LED camera is equipped with powerful LED illumination which reflects and disturbs the image if nearby structural parts of the vehicle are in the field of vision or just around the field of vision. Make sure the IR LED camera has a free area in the immediate surroundings of the camera to prevent these reflections. -
Page 10: Pin Connection
2 = Coax screen (Video GND) 3 = Red (12/24V/DC ) 4 = White (0V) Shielding connected to connector* *Shielding connected to Connector housing and Camera housing: AMOS, AMOS IR LED, MILMOS. *Shielding connected only to connector housing: CCC, CMOS. IM0973060 R2-6... - Page 11 Installation manual Soldering side of 4 pins male connector (1312001) (Camera with 4p connector): 1 = Coax core (Video signal) 2 = Coax screen (Video GND) 3 = Red (12V/DC ) 4 = White (0V) Shielding N.C. NOTE: The camera can operate in mirror-mode. Mirror-mode: Connect the orange wire to pin 3 red (+ 12V/DC).
- Page 12 Installation manual Soldering side of 7 pins male connector (1330500) (Camera with 7p connector): 1 = Coax core (Video signal) 2 = Coax screen (Video GND) 3 = Red (12V/DC) 4 = White (0V) 5 = N.C. 6 = N.C. 7 = N.C.
-
Page 13: Maintenance And Cleaning
Installation manual 3. Maintenance and cleaning Fixing a blurry image: If the camera image is blurry, it is advisable to clean the camera. Cleaning the lens glass: Use a soft cloth to clean the lens glass of the camera. Use clean water or a high quality and safe foam cleaner. -
Page 14: General Terms And Conditions
All rights reserved. No part of this manual may be reproduced and/or made public in printed form, in photocopy form or on microfilm, or in any other way, without the prior written permission of Orlaco. This also applies to the associated drawings and figures. -
Page 15: Revision Details
Installation manual 6. Revision details R1-0. First issue, June 2009. R1-1. Page 3, text added, April 2010. R1-2. Page 4, text added, Sept. 2010. R2-0. Article numbers added, dimensions layout changed, April 2011. R2-1. Camera type AMOS, MILMOS added, Nov. 2012. R2-2. - Page 16 ORLACO Orlaco is a Manufacturing company that specializes in making cameras and monitor systems for commercial vehicles, fork-lift trucks, cranes, off shore and maritime. Our objective is to design and produce camera systems for the professional market that improve the drivers’ view and increase operating efficiency.
Need help?
Do you have a question about the CCC and is the answer not in the manual?
Questions and answers