Fuel Tank Settings; Seven Marine Engine Installation Settings; Other Vessels Settings; Settings That Are Synced On The Garmin Marine Network - Garmin Volvo Penta Glass Cockpit B7 Owner's Manual

Before you can set the speed factor, the vessel must be
under way.
1 Select Settings > My Vessel > Speed Factor.
2 Enter the difference between the displayed speed and
the external data.
3 Verify that the two speed sources are displaying the
same value.

Fuel Tank Settings

Select Settings > My Vessel > Fuel Tank, and select a
driveline.
For more information, refer to the Volvo Penta manual.
Volume: Sets the fuel capacity of this fuel tank on your
vessel.
Empty Tank: Calibrates the empty tank level.
Multipoint: Calibrates various fuel levels between empty
and full.
Full Tank Calibration: Calibrates the full tank level.

Seven Marine Engine Installation Settings

Select Settings > My Vessel > Seven Marine
Installation.
DPS Button: Allows you to set the joystick button DPS
modes.
Trim Zero Set: Allows you to initialize the trim angle to
zero when all motors are fully trimmed down.
Tank Preset: Sets the tank name, fluid type, sensor style,
and tank capacity, and calibrates the sensor
(Configuring the Tank Level Sensors, page
Air Purge: Allows you to bleed air from the steering
system using the steering pumps.
Steer Sensor: Calibrates the engine steering system
using physical end stops. A physical end stop is the
point at which a steering wheel stops turning in a
direction.
Joystick Thrust: Allows you to set how hard the thrusters
work. Larger boats may need to select Maximum for
the boat to move, while Maximum joystick thrust may
provide too much thrust for smaller boats.
Lock to Lock: Allows you to set the number of turns from
lock to lock.
Steer Friction: Sets the friction on the steering wheel.
The friction is adjusted automatically according to the
engine speed.
Engine Distance: Allows you to set the distance between
drive lines to limit achievable steering angles for certain
engine distances.
Gear Rotation: Allows you to set the type of gear case on
the outboard to define forward and reverse shift
direction.
Gear Ratio: Allows you to set the ratio between the
rotation rates of the last and first gears.
Cruise Mode: Allows you to change the cruise control
mode between RPM and Speed mode.
Device Configuration

Other Vessels Settings

When your compatible chartplotter is connected to an AIS
device or VHF radio, you can set up how other vessels
are displayed on the chartplotter.
Select Settings > Other Vessels.
AIS: Enables and disables AIS signal reception.
DSC: Enables and disables digital selective calling (DSC).
Collision Alarm: Sets the collision alarm
Safe-Zone Collision Alarm, page
AIS-EPIRB Test: Enables test signals from Emergency
Position Indicating Radio Beacons (EPRIB).
AIS-MOB Test: Enables test signals from man overboard
(MOB) devices.
AIS-SART Test: Enables test transmissions from Search
and Rescue Transponders (SART).
Settings that are Synced on the Garmin
Marine Network
Garmin ECHOMAP
certain settings when connected to the Garmin Marine
Network.
The following settings are synced, if applicable, to the
device.
Alarm Settings (also syncs alarm acknowledgment):
• Arrival
• Anchor Drag
• Off Course
59).
• GPS Accuracy
• Shallow Water
• Deep Water (Not available in the GPSMAP 8400/8600
series)
• Water Temp.
• Contour (Not available in echoMAP 70s and GPSMAP
507/701 series)
• Fish
• Collision Alarm
General Settings:
• Auto Guidance Preferred Depth
• Auto Guidance Vertical Clearance
• Beeper
• Color Mode
• Keyboard Layout
• Language
• Map Datum
• Heading
• Position Format
• System Units
• Calibrate Water Speed
• Radar Antenna Size
Chart Settings:
• Chart Borders
(Setting the
15).
and GPSMAP chartplotters sync
™
81