Radar Overlay; Radar Overlay And Chart Data Alignment; Transmitting Radar Signals; Stopping The Transmission Of Radar Signals - Garmin Volvo Penta Glass Cockpit B7 Owner's Manual

In the screenshot below, the radar overlay is turned on.
This screen also shows a video feed. We can easily
identify a few items on the radar screen.

Radar Overlay

When you connect your chartplotter to an optional Garmin
marine radar, you can use overlay radar information on
the Navigation chart or on the Fishing chart.
Data appears on the radar overlay based on the most
recently used radar mode and all settings configurations
applied to the radar overlay are also applied to the last-
used radar mode.

Radar Overlay and Chart Data Alignment

When using the Radar overlay, the chartplotter aligns
radar data with chart data based on the boat heading,
which is based by default on data from a magnetic
heading sensor connected using a NMEA 0183 or NMEA
2000 network. If a heading sensor is not available, the
boat heading is based on GPS tracking data.
GPS tracking data indicates the direction in which the
boat is moving, not the direction in which the boat is
pointing. If the boat is drifting backward or sideways due
to a current or wind, the Radar overlay may not perfectly
align with the chart data. This situation should be avoided
by using boat-heading data from an electronic compass.
If the boat heading is based on data from a magnetic
heading sensor or an automatic pilot, the heading data
could be compromised due to incorrect setup, mechanical
malfunction, magnetic interference, or other factors. If the
heading data is compromised, the Radar overlay may not
align perfectly with the chart data.

Transmitting Radar Signals

NOTE: As a safety feature, the radar enters standby
mode after it warms up. This gives you an opportunity to
verify the area around the radar is clear before beginning
radar transmission.
1 With the chartplotter off, connect your radar as
described in the radar installation instructions.
2 Turn on the chartplotter.
If necessary, the radar warms up and a countdown
alerts you when the radar is ready.
3 Select Radar.
46
Land
Vessel
4 Select a radar mode.
A countdown message appears while the radar is
starting up.
5 Select Menu > Transmit Radar.

Stopping the Transmission of Radar Signals

From a radar screen, select Menu > Radar To
Standby.
TIP: Press > Radar To Standby from any screen to
quickly stop radar transmission.

Setting Up the Timed Transmit Mode

To help conserve power, you can set up time intervals in
which the radar will transmit and not transmit (standby)
signal transmissions.
NOTE: This feature is not available in dual radar modes.
1 From a radar screen, select Menu > Radar Options >
Timed Transmit.
2 Select Timed Transmit to enable the option.
3 Select Stdby Time, enter the time interval between
radar signal transmissions, and select Done.
4 Select Transmit Time, enter the duration of each
radar signal transmission, and select Done.

Enabling and Adjusting a Radar No Transmit Zone

You can indicate areas within which the radar scanner
does not transmit signals.
NOTE: GMR Fantom and xHD2 radar models support two
no-transmit zones. Most other GMR radar models support
one no-transmit zone. GMR 18 HD+ radar models do not
support no-transmit zones.
1 From a radar screen, select Menu > Radar Setup >
Installation > No Transmit Zone.
The no-transmit zone is indicated by a shaded area on
the radar screen.
2 Select Angle 1, and select the new location for the first
angle.
3 Select Angle 2, and select the new location for the
second angle.
4 Select Done.
5 If necessary, repeat for the second zone.

Adjusting the Radar Range

The range of the radar signal indicates the length of the
pulsed signal transmitted and received by the radar. As
the range increases, the radar transmits longer pulses in
order to reach distant targets. Closer targets, especially
rain and waves, also reflect the longer pulses, which can
add noise to the Radar screen. Viewing information about
longer-range targets can also decrease the amount of
space available on the Radar screen for viewing
information about shorter-range targets.
• Select to decrease the range.
• Select to increase the range.
Radar