Related Manuals for IWAKI PUMPS MX-F100
Summary of Contents for IWAKI PUMPS MX-F100
- Page 1 IWAKI Magnetic Drive Pump MX-F100 (Asia Edition) Instruction Manual Read this manual before use of product...
-
Page 2: Table Of Contents
Important Instruction Thank you for selecting an Iwaki MX-F type Magnetic Drive Pump. This instruction manual deals with "Safety Instructions", "Outline", For the Safe and "Installation", "Operation" and "Maintenance" sections. Correct Handling of the Pump Please read through this instruction manual to ensure the opti- ●... -
Page 3: Safety Instructions
Safety Instructions WARNING CAUTION ● Turn off the power. ● Restriction on operator Risk of electrical shock. Dismantling/ The pump should be handled by a qualified assembling the pump unit without turn- person with a full understanding. ing off the power may cause an electrical ●... - Page 4 Safety Instructions CAUTION CAUTION ● Do not run pump dry. ● Power cable is not replaceable. If the pump runs without a liquid, the pump Do not use any damaged power cable is damaged by friction heat. for the prevention of a fire or an electrical shock.
-
Page 5: Outline
Outline 2. Operating principle Before use, check the specification, limitation and hazardous nature of the pump. The MX-F is a magnetic drive centrifugal pump with fluoroplastic 1. Unpacking & Inspection and fine ceramic wet ends and is capable of handling a strong acid and alkali. -
Page 6: Identification Code
Flange connection Model Inlet Outlet Inlet Outlet MX-F100 (M/FL) c. Wet end material NOTE: RV : PTFE (bearing)/ FKM (O ring) a. Performance data is based on pumping of clear water at ambient KV : SiC (bearing)/ FKM (O ring) temperature. -
Page 7: Outer Dimensions
Outline 5. Outer dimensions MX-F100FL MX-F100M 319.5 4-27 4-27 - 5 -... -
Page 8: Performance Curves
Outline 6. Performance curves 7. Overview & Label 50Hz Pump unit (Liquid feeding unit) Not capable of self-priming. Always prime the pump before operation. MX-F100Y Specification label Use the pump accord- ing to the specifica- Outlet tions on the label. ℓ/min 60Hz MX-F100Y... -
Page 9: Part Names & Structure
Outline 8. Part names & Structure MX-F100M Materials Materials Part names Q'ty Part names Q'ty MX-F100RV MX-F100KV MX-F100RV MX-F100KV Front casing CFRETFE 10 Rear thrust ring Alumina ceramics Bearing A PTFE 11 Driven magnet Rear casing CFRETFE 12 Drive magnet unit Bearing B PTFE 13 Drive magnet... - Page 10 Outline MX-F100FL 11 13 13 11 101 14 Materials Materials Part names Q'ty Part names Q'ty MX-F100RVFL MX-F100RVFL Front casing CFRETFE 11 Drive magnet Bearing A PTFE 12 Drive magnet unit Ferrite magnet + Aluminium alloy Rear casing CFRETFE 13 Driven magnet Bearing B PTFE 14 Hex.
-
Page 11: Installation
Installation 1. Before Installation ● Dropping or subjecting the pump to strong impact, failure may result. Read through this section before use. Carry out installation work Handle the pump with care. with a full understanding. WARNING ● Risk of electrical shock. Turn off power immediately ●... - Page 12 Installation ● Banned solutions CAUTION • Liquids that significantly swell poly- Do not install or store the pump in the propylene following places where... • Paraffinic hydrocarbons such as • Ambient temperature is beyond the gasoline and kerosene range of 0 - 40°C. •...
-
Page 13: Installation/Piping/Electrical Wiring
Installation 2. Installation/ Piping/ Electrical wiring 3. Outlet direction Always direct the outlet upward, or Stop working upon sensing a danger in work. entrained air can not be expelled. 2.1 Installation CAUTION 1. Installation location Do not mount the pump vertically, Select a convenient place for main- directing the pump head upward. - Page 14 Installation 3. Install valves on both discharge and <Thread connection> Discharge- suction lines. Wrap a thread seal tape around the side valve • Suction-side valve: exposed threads of a pipe before it is For easy pump removal and main- screwed in to create an air- and water- tenance.
- Page 15 200 or 220V 200 or 220V 100V (1-phase) 100V (1-phase) (3-phase) (3-phase) accident due to nonobservance of this warning. Contact us or your MX-F100 4.1A/4.1A 1.2A/1.2A 8.4A/8.2A 3.7A/3.4A nearest dealer for wiring as necessary. ■ Before wiring 1. Confirm that the power is disconnected before work.
-
Page 16: Operation
Operation 2. Operation 1. Before operation The pump doesn't have the ON-OFF switch. The pump starts as Read through this section before use. the power cable is plugged in. After installation, piping and wiring CAUTION work are completed, operate the pump in accordance with the fol- lowing procedures. - Page 17 Operation ■ Degassing Procedure Points to be checked Open a discharge line. The end of the line immersed in liquid is not Adjust a discharge Open a discharge-side valve gradu- ideal for degassing. Take it out from liquid as necessary. Then run the capacity &...
- Page 18 Operation ■ Shutdown ■ Before a long period of stoppage Empty the pump before it is stopped for a long time. In this period of Procedure Description time run the pump with clean water for 5 minutes every 3 months to Close a discharge- Close the discharge-side valve prevent the motor bearing from being stuck.
-
Page 19: Maintenance
Maintenance 2. Maintenance & Inspection 1. Troubleshooting ■ Retightening Handling of the pump, maintenance and inspection should be car- ried out within this instruction manual. Do not handle the pump After a long period of operation or storage, the pump head mount- beyond the descriptions in this manual. -
Page 20: Drainage
Maintenance 3. Drainage ■ Wear parts To run the pump for a long period, wear parts such as impeller and O The pump does not have a drain port. See next procedure for ring need to be replaced periodically. detail. Contact your distributor for detail. - Page 21 IWAKI Norge AS TEL : (47)66 81 16 60 FAX : 66 81 16 61 China IWAKI Pumps (Guandong) Co., Ltd. TEL : (86)750 3866228 FAX : 750 3866278 Singapore IWAKI Singapore Pte. Ltd. TEL : (65)6316 2028 FAX : 6316 3221 China GFTZ IWAKI Engineering &...
Need help?
Do you have a question about the MX-F100 and is the answer not in the manual?
Questions and answers