Related Manuals for Custom Equipment Hy-Brid Lifts 2 Series
Summary of Contents for Custom Equipment Hy-Brid Lifts 2 Series
- Page 1 MAIN NTEN NANCE ROUB BLESH HOOTI MANUA y-Brid Lifts Mode HB-P83 Series Push-Aro ound Aerial l Work P Platform ...
-
Page 2: Table Of Contents
Table of Contents Safety and Control Decals ........................28 Safety ................................5 Main Power/Safety Circuit........................29 Safety Symbols ............................5 Elevate/Lower Circuit Parts........................30 General Rules and Precautions ......................... 5 Wheels/Brakes ............................31 Stability Testing ............................6 Other ............................... 32 Safety Guidelines ............................ -
Page 3: Safety
THE USER/OPERATOR SHOULD NOT ACCEPT OPERATING RESPONSIBILITY UNTIL THE Custom Equipment, Inc. designed the Hy-Brid Lift push-around scissor lift to be safe and reliable. It is intended for elevating personnel, along with their necessary tools and materials to overhead work MANUAL HAS BEEN READ AND UNDERSTOOD AS WELL AS HAVING OPERATED THE locations. -
Page 4: Stability Testing
Stability Testing Safety Guidelines Maintenance Lock The HB-P830CE has been stability tested to standards EN280 or AS 14180. The most adverse stability The maintenance lock must be placed into position whenever the machine is being serviced in the raised test is the stationary, lateral slope configuration for both units. The overturning moment created by the or partially raised position. -
Page 5: Battery Maintenance
Battery Maintenance This unit is equipped with a deep cycle 12-volt Group 27 battery. The care and maintenance of your battery has much to do with how well this unit functions. Battery wiring and water level should be checked monthly. Do not overfill. -
Page 6: Storage
Storage Prestart Inspection Checklist After periods of storage, exposure to extremes of ambient conditions-heat, cold, moisture, dust etc. inspect the machine. Refer to the Pre-Delivery/ Frequent Inspection Checklist in the Maintenance Manual. WARNING Major Alterations or Repairs THIS CHECKLIST MUST BE USED AT THE BEGINNING OF EACH SHIFT OR AFTER EVERY SIX TO EIGHT HOURS OF USE. Any alterations must be approved by the manufacturer. - Page 7 Frequent Inspection Checklist Pre-Delivery/Annual Inspection Checklist WARNING WARNING AERIAL PLATFORMS SHALL BE INSPECTED, SERVICED AND ADJUSTED TO MANUFACTURER'S AERIAL PLATFORMS SHALL BE INSPECTED, SERVICED AND ADJUSTED TO MANUFACTURER'S REQUIREMENTS BY A QUALIFIED REQUIREMENTS BY A QUALIFIED MECHANIC PRIOR TO EACH SALE, LEASE, OR RENTAL, AND EVERY MECHANIC PRIOR TO EACH SALE, LEASE, OR RENTAL, AND EVERY 12 MONTHS 3 MONTHS OR 150 HOURS, WHICHEVER COMES FIRST MODEL NUMBER HB-P830CE SERIAL NUMBER ______________...
- Page 8 This page intentionally left blank. Part# SUPO-633E Page 14 of 34 Part# SUPO-633E Page 15 of 34 REV C REV C...
- Page 9 Part# SUPO-633E Page 16 of 34 Part# SUPO-633E Page 17 of 34 REV C REV C...
- Page 10 Part# SUPO-633E Page 18 of 34 Part# SUPO-633E Page 19 of 34 REV C REV C...
- Page 11 Part# SUPO-633E Page 20 of 34 Part# SUPO-633E Page 21 of 34 REV C REV C...
- Page 12 Troubleshooting Flowcharts--General Notes: See also Main Power & Safety Circuit WARNING WARNING Inspect parts for visible damage as they are encountered. Wiring Diagram: WD-HB-P830CE Power Any modification on this machine without Failure to comply with safety precautions After each step, check if problem has been indentified and/or resolved. the express consent of the manufacturer may result in damage, injury, or death.
-
Page 13: Hydraulic Schematic
Troubleshooting Flowcharts--General Notes: WARNING Any modification on this machine without WARNING: Set up for maintenance safety: See also Inspect parts for visible damage as they are encountered. Wiring Diagram WD-HB-P830CE Elevating the express consent of the manufacturer Remove load from platform. After each step, check if problem has been indentified and/or resolved. - Page 14 Troubleshooting Flowcharts--General Notes: WARNING Any modification on this machine without Inspect parts for visible damage as they are encountered. See also WARNING: Set up for maintenance safety: After each step, check if problem has been indentified and/or resolved. the express consent of the manufacturer Wiring Diagram WD-HB-P830CE Elevating Remove load from platform.
-
Page 15: Replacement Parts
Replacement Parts Main Power/Safety Circuit CAUTION USE ONLY MANUFACTURER APPROVED REPLACEMENT PARTS. USE OF NON-OEM PARTS WILL VOID WARRANTY. DANGER REPLACEMENT OF THE FOLLOWING COMPONENTS WILL AFFECT THE STRENGTH, STABILITY, OR SAFETY FUNCTION OF THE UNIT: BATTERY, HYDRAULIC CYLINDER , AND ALL STRUCTURAL COMPONENTS. - Page 16 Elevate/Lower Circuit Parts Wheels/ /Brakes Item # Part # Description ELEC-635 Descent Alarm Item # Part # Description HYDR-050-7 Hydraulic Pump 1002103160 Rigid Caster Assembly ELEC-635-1 Overload Alarm ELEC-636 Overload Indicator Light WHEE 706 KI Wheel (8”) ELEC-632 Time Delay Relay WHEE 002 1 Bearing Kit ELEC-133B...
- Page 17 Other Warranty LIMITED PRODUCT WARRANTY Limited Warranties. Subject to the terms, conditions and limitations set forth herein, Custom Equipment, Inc. (the “Company”) warrants to the first end user (“Buyer”) that: Limited Product Warranty. For a period of 24 months from the date that a new product manufactured by the Company (“Product”) is delivered to the Buyer, the Product will (i) conform to the specifications published by the Company for such Product as of the date of delivery;...
- Page 18 Company. The Company reserves the right to review Buyer’s maintenance and operation records and procedures to determine if the alleged defect(s) were due to any of the items listed in Sections 2 of this Limited Warranty. The Company shall not be liable for any claim under this Limited Warranty if Buyer fails to satisfy the conditions set forth in this Section. 4. Exclusive Repair or Replace Warranty Remedy. The Company’s sole obligation and Buyer’s exclusive remedy with respect to any defect in the Product occurring during the warranty periods set forth in Section 1 of this Limited Warranty shall be for the Company, at its option, to ...
Need help?
Do you have a question about the Hy-Brid Lifts 2 Series and is the answer not in the manual?
Questions and answers