Subscribe to Our Youtube Channel
Related Manuals for Erbauer ERB610MSW
Summary of Contents for Erbauer ERB610MSW
- Page 1 Original Instructions Patent Pending 1008829.2 Read instructions fully before operating this tool ERB610MSW (SKU NO 61027 - J1Y-KZ12-255J) ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 2 ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 3 Congratulations on your purchase of a quality power tool from Erbauer Ltd. This product should give you reliable service for your peace of mind this power tool does carry a 24-month guarantee, the terms of which are detailed below. If this product develops a fault within the guarantee period contact your retailer.
-
Page 4: Safety Instructions
11 Do not abuse the cord - Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 5 - The use of any accessory or attachment other than one recommended in this instruction - This electric tool complies with the relevant safety rules. Repairs should only be considerable danger to the user. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
-
Page 6: Health Advice
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 7 Do not use dull or damaged blades. Unsharpened or improperly set blades produce f. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 8 17. Select saw blades in relation to the material to be cut. 18. Check the maximum depth of cut. 19. When sawing long work pieces, always use extra support to provide better support, and use clamps or other clamping devices. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 9 Remove the mains plug from socket before carrying out SAFETY RULES FOR LASER LIGHT wavelength. These lasers do not normally present an optical hazard, although staring at the beam may WARNING! ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
-
Page 10: Specific Safety Rules And Symbols
Amperes Hertz Speed Alternating Current No Load Speed Double Insulated Wear Safety Goggles Wear Ear Protection Wear Dust Mask Read Instruction Manual Laser Warning Symbol Conforms to relevant safety standards General Warning ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 11 4. LOWER BLADE GUARD 5. BLADE 6. TABLE INSERT 7. MITRE HANDLE 8. LASER GUIDE 9. BASE 10. TURNTABLE 11. LEFT EXTENSION TABLE 12. FENCE 13. HOLD-DOWN CLAMP 14. SLIDE CARRIAGE LOCK KNOB ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 12 16. SLIDE CARRIAGE 17. BEVEL LOCK HANDLE 18. RIGHT EXTENSION TABLE 19. MOTOR 20. POSITIVE STOP LOCKING LEVER 21. LOWER BLADE GUARD LOCK LEVER 22. LASER ON/OFF SWITCH 23. ADJUSTABLE CUTTING STOP ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
-
Page 13: Technical Data
(taking account of all parts of running idle in addition to the trigger time). ACCESSORIES Allen Key 1 pc, Dust Bag 1 pc, Hold-Down Clamp 1 pc & Mitre Handle 1 pc ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 14 Health Surveillance All employees should be part of an employer’s health surveillance scheme to help identity any vibration related diseases at an early stage, prevent disease progression and help employees stay in work. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 15 IMPORTANT To avoid damage, never carry the mitre saw by the cutting arm or the mitre handle. ALWAYS use both designated carrying handles together. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 16 5. Installing the hold-down clamp WARNING! Always check clamp position does not interfere with any saw operation. Before switching on, lower the saw head to ensure the clamp clears the guard and saw head assembly. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 17 Use 4) Mitre saw base G-clamps to clamp this mounting board to a stable Note: Mounting hardware is not included with this tool. Bolts, nuts, washers and screws must be purchased separately. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 18 Note: Pay attention to the pieces removed, noting their position and direction they face. Wipe the blade collars clean of any sawdust before installing a new blade. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 19 Make sure the collars are clean and properly arranged. Check that the lower blade guard is functioning correctly and does not bind or stick. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 20 “pattern line” to test laser alignment. Lay the board on the mitre table. 2) Plug saw into socket and turn on the laser beam and line it up with the pattern line. may be necessary. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 21 WARNING! Use only the correct sized Turn one screw at a time and only ¼ turn in either direction before checking laser alignment. Maintain as far as possible the original factory pressure module. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
-
Page 22: Adjustment Instructions
° ° cutting head to the left, loosen the locknut (4) on the out to increase or decrease the bevel angle. ° °) bevel and recheck for alignment. needed. when alignment is achieved. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 23 6. Bevel adjustment 33.9 ° settings can be checked and ° ° (RH) by deploying the crown moulding pin. Check the angle of the blade against the machine table using the vernier angle ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 24 Phillips screwdriver. 9. Adjusting fence squareness 2) Lower the cutting arm and lock in position. against the blade and the ruler against the fence(2) as shown. four fence locking bolts. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 25 4) Recheck the blade depth by moving the cutting head front to back through the full motion of a cut along the control arm. If the blade touches the inside locknut when the correct setting is achieved. (See ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 26 Make sure bystanders are clear of the saw and workpiece. Don’t force the saw. It will do Starting a cut: prevent movement toward the blade. down to the workpiece to see the cutting path of the blade ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 27 Before leaving the saw OFF. Wait for all moving parts to stop. Disconnect master switches. Store tool away from ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 28 2) Tilt the cutting head to the desired angle, as shown on the bevel scale (2). cutting head in position. Positive stops are provided Note: does not catch on work or machine base plate. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 29 The cutting head assembly should be drawn back completely then pushed forward when sawing. will help reduce the risk of a thrown workpiece. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 30 To replace, simply slide the satellite stand back into the machine base until the release button ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 31 Adjusting the stop plate Deploy the stop plate as outlined above. machine base below the stop plate. clockwise or counter 13. Extension Arm With the stop plate in its stored position the ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 32 Mitre saw table a 90° inside or outside corner, lay the moulding When setting the bevel and mitre angles for compound mitres, remember that the settings are interdependent – changing one changes the other, ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 33 WHEN THE ANGLE BETWEEN THE WALLS EQUALS 90 BEVEL MITRE TYPE OF CUT SETTING SETTING Inside Corner-Left side Right Inside Corner-Right side Left fence. Outside Corner-Left side fence. Left Outside Corner-Right side Right ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
-
Page 34: Maintenance
Develop a regular check to make sure the lower guard is working properly. Clean the lower guard of any dust or buildup with a damp cloth. ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 35 ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
-
Page 36: Environmental Protection
N. The wire that is coloured brown must be connected to the terminal that is marked with the letter L. 5 AMP FUSE BLUE N (NEUTRAL) BROWN L (LIVE) OUTER SLEEVE CABLE GRIP ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW... - Page 37 Complies with the essential health and safety 2004/108/EC – EMC Directive 2006/95/EC – Low Voltage Directive 2006/42/EC – Machinery Directive EN55014-1 EN55014-2/A2 EN61000-3-2 EN61000-3-11 EN61029-1 EN61029-2-9 EN60825-1 Authorised Signatory Erbauer (UK) Ltd Quality Manager ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 38 ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 39 ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
- Page 40 ERBAUER 254MM (10”) DOUBLE BEVEL SLIDING MITRE SAW...
Need help?
Do you have a question about the ERB610MSW and is the answer not in the manual?
Questions and answers