Erbauer ERB2504SE User Manual
  1. Manuals
  2. Brands
  3. Erbauer Manuals
  4. Saw
  5. ERB2504SE
  6. User manual

Erbauer ERB2504SE User Manual

2500mm
Hide thumbs
Table of Contents

Advertisement

Quick Links

ERB2504SE
ERBAUER 250MM TABLE SAW
2 2
WARRANTY
WARRANTY
YEARS
YEARS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ERB2504SE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Erbauer ERB2504SE

Summary of Contents for Erbauer ERB2504SE

  • Page 1 WARRANTY WARRANTY YEARS YEARS ERB2504SE ERBAUER 250MM TABLE SAW...
  • Page 2 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 3 This guarantee does not affect your statutory rights. This guarantee is only valid in the UK. For further technical advice and spare parts, Please contact the customer helpline number on 01709 876611 quoting your Erbauer model number. ERBAUER 250MM TABLE SAW...

  • Page 4: Work Area

    Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 5: Health Advice

    You should: - Work in a well-ventilated area. - Work with approved safety equipment, such as those dust masks that are specially designed to fi lter microscopic particles. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 6 When transporting the machine use only transportation devices and do never use guards for handling or transportation. g. During transportation the upper part of the saw blade should be covered , for example by the guard. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 7 14. NEVER USE SOLVENTS to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material. Only a soft damp cloth should be used to clean plastic parts. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 8 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 9: Double Insulation

    Wear gloves Wear gloves Wear gloves Wear gloves Wear gloves Wear gloves Wear gloves Wear gloves Symbol for transportation Wear dust mask, eye & ear protection position Conforms to relevant safety standards ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 10 ADJUSTABLE STAND PAD ADJUSTABLE STAND PAD 11. NO-VOLT-RELEASE (NVR) SWITCH NO-VOLT-RELEASE (NVR) SWITCH 12. BEVEL ANGLE POINTER & SCALE BEVEL ANGLE POINTER & SCALE AUXILIARY FENCE AUXILIARY FENCE FENCE STORAGE FENCE STORAGE ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 11 Fig 2 17. TABLE INSERT TABLE INSERT MITRE GAUGE STORAGE MITRE GAUGE STORAGE 20. DUST PORT DUST PORT ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 12: Technical Data

    Maximum cut depth @ 45 Maximum cut depth @ 63mm Machine weight: 26.5 kg NOISE AND VIBRATION DATA NOISE AND VIBRATION DATA Sound pressure level: 95.4 dB (A) Sound power level: 108.4 dB (A) ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 13 2 pc Table side extension hardware bag 1 pc Dust port adapter 1 pc STAND 4 pc Foot pad 3 pc Fence storage clip hardware bag 1 pc Stand hardware bag 1 pc ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 14 (5) and nuts (6). 8) Repeat these procedures for the left extension table (See fi g. 1). Description Size M6*1.0-12 bolts (4) M6*1.0 T=5 nuts (2) M6*1.0-12 bolt (5) M6*1.0 T=6 nut (6) Fig 1 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 15: Stand Assembly

    (See fi g. 2-1). Note: The tools to mount this saw is not supplied with the saw. Description Size M6*1.0-45 hex bolt (3) φ6*18-1.5 washer (4) M6*1.0 T=4 nut (5) Fig 2 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 16 (2) clockwise (to the rear of the saw table). 7) Replace the table insert and retighten the two screws. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 17 5) Check the riving blade and blade alignment again at both 90° and 45°. 6) Add or remove the spacers until the alignment is correct. 7) Replace the table insert. (See fi g. 7). ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 18 fi rst. 3) Push down on the fence handle (1) to lock 4) Place the mitre gauge (3) in the groove (4) on the table top. (See fi g. 11). Fig 11 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 19 (1) and carefully grasp the saw blade. Make necessary correction until measurements taken at the front and rear are identical. Tighten the four screws (1) (See fi g. 14). ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 20: Adjusting Rip Fence

    Move the far end of the fence until it is parallel with the mitre gauge groove. ● Push the handle down to lock it, and tighten both screws. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 21 (6) on the bar, adjust the pointer to the 90° position and retighten the pointer screw (See fi g. 17). Fig 17 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 22: Operating Instructions

    ●To move the rip fence, loosen the clamp handle while pressing the fence bracket against the table surface and set the desired distance from the saw blade, retighten the clamp handle. ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 23 6) When the width of rip is more than 150 mm, feed the workpiece with one or both hands continuously until it is beyond the saw blade and riving blade (See fi g. 19). ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 24 5) When performing bevel cross cutting, only work with the workpiece and mitre gauge on the right side of the saw blade (See fi g. 20). ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 25 3) Set the blade (1) bevel to the desired bevel angle and tighten the blade bevel lock knob. 4) Hold workpiece fi rmly against the face of the mitre gauge (3) throughout the cutting operation (See fi g. 22). ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 26 12. Transportation the machine 1) Symbol for transportation position (See fi g. 25). Warning: When transporting the machine use only transportation devices and do never use guards for handling or transportation. Fig 25 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 27: General Maintenance

    3) Tighten nut (2) with a second 14 mm spanner, while holding nut (3) with the fi rst spanner in place. Maximum allowable play of screw rod (1) is 0.16 in. (4 mm) (See fi g. 26). ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...

  • Page 28: Environmental Protection

    A 13AMP (BS1363 or BS1363/A) plug must be used and a 5 AMP fuse must be fi tted. 5 AMP FUSE BLUE N (NEUTRAL) N (NEUTRAL) BROWN L (LIVE) OUTER SLEEVE CABLE GRIP ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 29 Standards and technical specifi cations referred to: EN 55014-1:2000/+A1:2001/+A2:2002 EN 55014-2:1997/+A1:2001 EN 61000-3-2:2006 EN 61000-3-3:1995/+A1:2001/+A2:2005 EN 61029-2-9:2002 EN 61029-1:2000 Authorised Signatory Date: 2/14/07 Signature: Name: Peter Harries Erbauer (UK) Ltd Quality Manager 2007 ERBAUER 250MM TABLE SAW ERBAUER 250MM TABLE SAW...
  • Page 30 ERBAUER 250MM TABLE SAW...

Table of Contents