1. Manuals
  2. Brands
  3. Smith & Noble Manuals
  4. Window Blinds
  5. Cellular Shades
  6. Step by step installation instructions

Smith & Noble Cellular Shades Step By Step Installation Instructions

Motorized
Hide thumbs Also See for Cellular Shades:
Table of Contents

Advertisement

Quick Links

STEP BY STEP INSTALLATION INSTRUCTIONS
Cellular Shades
Top Down/Bottom Up
and Day/Night
Motorization

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cellular Shades and is the answer not in the manual?

Questions and answers

Related Manuals for Smith & Noble Cellular Shades

Summary of Contents for Smith & Noble Cellular Shades

  • Page 1 STEP BY STEP INSTALLATION INSTRUCTIONS Cellular Shades Top Down/Bottom Up and Day/Night Motorization...

  • Page 2: Table Of Contents

    Overview - Cellular Shades Motorization . . . . . . . . . . . . . . . . . .

  • Page 3: Step 1 - Getting Started

    STEP 1 — GETTING STARTED OVERVIEW Motorization Parts & Tools Before you begin, check the accompanying diagram to make sure you have all the parts you need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough to accommodate the brackets.

  • Page 4: Step 2 - Brackets Installation

    STEP 2 — BRACKET INSTALLATION STEP 2 — BRACKET INSTALLATION OUTSIDE MOUNT W/ SPACER BLOCK Spacer Blocks (Optional Using the installation bracket as a template, measure to the center of the bracket and shades 36" or wider, required for 36" or under) mark the hole locations with a pencil for drilling .

  • Page 5: Step 3 - Shade Installation & Removal

    IMPORTANT: Please pair the shade to the remote and smart hub prior to shade installation. Please go to p11 Pair the Remote in the Operating & Programming Guide. Level the Bottom Rail (If Necessary) Shade Installation Cellular shades use a system that allows ADJUSTMENT ADJUSTMENT Before mounting the head rail make sure SCREW...

  • Page 6: Hold Down Brackets (Optional)

    HOLD DOWN BRACKETS (OPTIONAL) Hold Down Brackets (Optional) Optional hold down brackets Smith & Noble mounted with the supplied screws. With the shade at its proper drop, place the pin of each hold down into the hole in Smart Shades each end cap and mark the screw holes.
  • Page 7 (COVER ON) used to operate top-down/bottom-up REMOTE FRONT beeps. It must be pressed before the last cellular shades. You cannot mix standard LIMIT long beep. The motor will respond with 3 BUTTON bottom-up only shades and a top-down/ fast beeps confirming that the shade has bottom-up shade on the same channel.
  • Page 8 OPERATING THE REMOTE UNPAIR THE REMOTE REMOTE BACK (COVER OFF) To unpair a shade(s) from a selected Select the desired channel with the channel, remove the cover on the back CHANNEL button. of the remote. Then press and release CHANNEL ON/OFF Use the RAIL SELECTOR to choose the CONFIRM button on the back of the...
  • Page 9 SETTING SHADE LIMITS SETTING SHADE LIMITS Adjust Shade Limits (If Desired) Use the RAIL SELECTOR button to choose rail no . 1 . The lower and upper limits have been Remove the cover on the back of the set at the factory. If you need to make remote.
  • Page 10 SETTING & USING A FAVORITE POSITION ADD OR REMOVE REMOTE OR CHANNEL CHANNEL Replace Original Remote, Add If there is only a single shade on the channel CHANNEL DISPLAY DISPLAY Additional Remote or Add Shade to proceed to SETTING A FAVORITE POSITION below .
  • Page 11 ADD OR REMOVE REMOTE OR CHANNEL DE-ACTIVATE JOG FUNCTION To De-Activate the Jog Function CHANNEL Remove a Shade from a Remote or DISPLAY 1 . The remote comes pre-set with Channel and Pair it to a Different jogging function activated. Follow Remote or Channel the directions below if you would like ON/OFF...
  • Page 12 CHARGING SHADE SOLAR PANEL (OPTIONAL) Charging Shade When the shade begins to operate Determine Solar Panel Placement slower than normal it is time to charge The solar panel should be placed where the motor. Plug the 8.4v charger into the it gets the maximum amount of sunlight wire.

  • Page 13: Solar Recharge Unit (Optional)

    INSTALL SOLAR PANEL INSTALL SOLAR PANEL Tape Method SOLAR PANEL RECHARGE UNIT Connect Solar Panel to Motor Cut the tape to fit inside the white After the shade is installed, plug the border as shown. Clean the ends of the solar unit into the motor recharge port.

  • Page 14: Troubleshooting

    TROUBLESHOOTING CARE & CLEANING Care & Cleaning PROBLEM SOLUTION The shade fabric is easy to care for. Regular dusting with a feather duster or vacuum cleaner Shade will not raise or lower. Recharge motor. brush is recommended. Most stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and lukewarm water, test an unobtrusive Shade runs slowly.

  • Page 15: Warranty

    Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship.

This manual is also suitable for:

Cellular top down/bottom up shadesCellular day/night shades

Table of Contents