Advertisement
HALL EFFECT SWITCH OPTION
SPECIFICATIONS
Type:
Solid State Type (PNP or NPN)
Switching Logic:
Normally Open
Supply Voltage Range:
5 - 30VDC
Current Output Range:
Up to100 mA at 5 VDC,
Up to 200 mA at 12 VDC and 24 VDC
Current Consumption:
7 mA at 5 VDC, 15 mA at 12 VDC,
and 30 mA at 24 VDC
Switching Response:
1000 Hz Maximum
Residual Voltage:
1.5V Maximum
Leakage Current:
10uA Maximum
Breakdown Voltage:
1.8kVACrms for 1 sec., lead to case
Min. Current for LED:
1mA
Operating Temperature:
14° to 140° F (-10° to 60° C)
Lead Wire Length:
39 inches (1meter)
(RED)
BROWN**
(WHITE)
LOAD
SWITCH
BLACK**
(BLACK)
BLUE**
PROXIMITY SWITCHES
The inductive type proximity switch provides end of rotation indication.
The non-contact probe senses the presence of the ferrous cushion
spear and has no springs, plungers, cams or dynamic seals that can
wear out or go out of adjustment. The switch is solid state and meets
NEMA 1, 12 & 13 specifications. For ease of wiring the connector
housing is rotatable through 360°. To rotate, lift the cover latch,
position, and release.*
The standard proximity switch controls 20-230 VAC/DC loads from 5 to
500 mA. The low 1.7 mA off-state leakage current can allow use for
direct PLC input. The standard short circuit protection (SCP) protects
the switch from a short in the load or line upon sensing such a condition
(5 amp or greater current) by assuming a non-conductive mode. The
fault condition must be corrected and the power removed to reset the
switch preventing automatic restarts.
The low voltage DC switch is also available for use with 10-30 VDC.
This switch is in a non-rotatable housing, but does incorporate the short
circuit protection.
Both switches are equipped with two LEDs, "Ready" and "Target". The
"Ready" LED is lit when power is applied and the cushion spear is not
present. The "Target" LED will light and the "Ready" LED will go out
when the switch is closed, indicating the presence of the cushion spear.
Both LEDs flashing indicates a short circuit condition.
NOTES:
1. Available with or without cushions.
2. Not available with stroke adjusters.
3. Pressure rating: 1500 psi
4. Operating temperature: -4°F to 158°F
5. Specify switch type, orientation and voltage when ordering.
6. Not available on PTR/LTR 10 size units.
7. The low voltage DC switch is available in non-rotatable style
only; consult representative for further information.
HIGH VOLTAGE SWITCH (20-230 VAC/DC)
Wiring Diagram and Information
AC
White (3)
SW
Black (2)
Internally Short
Circuit Protected
+
* When connecting Inductive
Load (relay, electromagnetic
valve etc.) it is recommended
to insert protection circuit.
Diode 100V 1A. (NPN
_
connection shown)
Pin Receptacle
AC
L1
Color Code
L2
1
1. Green
2. Black
3
3. White
2
Brad Harrison 40909 Connector
PNP WIRING CONNECTION
(RED)
BROWN**
(WHITE)
SWITCH
BLACK**
(BLACK)
BLUE**
NPN WIRING CONNECTION
(RED)
BROWN**
(WHITE)
SWITCH
BLACK**
(BLACK)
BLUE**
** Applies to Switches Manufactured
After 10/15/93.
58
65
64
59
60
62
63
ITEM
DESCRIPTION
NO.
REED SWITCH KIT
55
(Lead Type or Quick Connect)
56
MAGNET
HALL EFFECT SWITCH KIT
57
(Lead Type or Quick Connect)
58
PROXIMITY SWITCH
59
O-RING, ADAPTOR BLOCK
60
SCREW, SPACER BLOCK
61
SPACER BLOCK
62
O-RING, SPACER BLOCK
63
END CAP
64
ADAPTOR BLOCK
65
SCREW, ADAPTOR BLOCK
NOTE: Quantities shown are as required per end cap option specified.
LOW VOLTAGE DC SWITCH (10-30 VDC)
Wiring Diagram and Information
White (1)
Orange (4)
SW
Black (5)
Red (2)
Pin Receptacle
DC
Color Code
6
+
DC 5 - 30V
LOAD
_
Quick Connect
1 Brown
+
3 Blue
LOAD
DC 5 - 30V
_
61
(+)
Sink
(NPN)
(-)
Source
(PNP)
1. White: +10 to 30 VDC
3
2. Red: Source
2
4
3. Ground Not Connected
Nor Requied (Green)
5
1
4. Orange: Sink
5. Black: Common
Brad Harrison 41310 Connector
Option
4 Black
57
56
QTY.
1
2
1
1
1
4
1
1
1
1
2
Advertisement
