Related Manuals for Hayward SwimPure Plus
Summary of Contents for Hayward SwimPure Plus
- Page 1 SwimPure Plus SwimPure Plus SwimPure Plus SwimPure Plus SwimPure Plus ® ® ® ® ® Operation and Installation Manual AQR-SWP www.hayward.com...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL • INSTRUCTIONS • Use Copper Conductors Only • Disconnect all AC power during installation. • Warning - To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
- Page 3 Table of Contents OPERATION OPERATION OPERATION OPERATION OPERATION General General..................1 General General General Water Chemistry Water Chemistry Water Chemistry Water Chemistry..............1 Water Chemistry Controls Controls..................6 Controls Controls Controls Maintenance Maintenance................8 Maintenance Maintenance Maintenance INSTALLATION INSTALLATION INSTALLATION INSTALLATION INSTALLATION Mounting Mounting..................10 Mounting Mounting Mounting...
- Page 4 3 different chlorinator cells that are available from your autho- rized Hayward dealer. These cells are not included with the SwimPure Plus and must be purchased before installation. Choose the appropriate cell based on the size of your pool.
- Page 5 Your Authorized SwimPure Plus Dealer or most pool stores can provide you with the chemicals and procedures to adjust the water chemistry. Be sure to tell the pool store that you are using an SwimPure Plus chlorine generator. Saturation index The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool water "balance".
- Page 6 SwimPure Plus and result in low chlorine production. A high salt level can cause the SwimPure Plus to shutdown and may begin to give a salty taste to your pool (generally, the salt will begin to be tasted at a level of about 3500-4000 ppm). The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming season should be small.
- Page 9 OFF: The OFF position prevents the SwimPure Plus from energizing the electro- lytic cell. In this position there is no chlorine generation. NOTE: To service any of the pool equipment or the SwimPure Plus, turn the power off at the circuit breaker.
- Page 10 To Set Chlorinator Cell Type Before operation, the SwimPure Plus must be configured for the chlorinator cell that will be used. Refer to the following information and steps below to set the chlorinator cell type. "t-3" = T-CELL-3, GLX-CELL-3-W "t-5" = GLX-CELL-5, GLX-CELL-5-W "t-9...
- Page 11 To maintain maximum performance, it is recommended that you open and visually in- spect the cell every 3 months or after cleaning your filter. The SwimPure Plus will remind you to do this by flashing the "Inspect Cell" LED after approximately 500 hours of operation.
- Page 12 Spring Start-up DO NOT turn the SwimPure Plus on, until the pool water chemistry has been brought to the proper levels. This information can be found on page 1.
- Page 13 Refer to page 1 for recommended chemical levels. The pool's chemistry must be bal- anced BEFORE activating the SwimPure Plus. NOTE: If the pool does not have new water, add 1 quart (1 liter) of metal remover and 1 quart (1 liter) of non-copper based algaecide to the pool, per manufacturer's instructions.
- Page 14 Ensure that the SwimPure Plus installation does not constitute a cross connection with the local potable water supply. Consult local plumbing codes. The SwimPure Plus is packaged with a flow switch and cell unions. The cell must be purchased separately. Refer to page 1 for information about available chlorinator cells.
- Page 15 Input Power For stand alone operation: Wire the SwimPure Plus to the LOAD SIDE of the filter pump timer. It is very important that the SwimPure Plus is powered only when the pump is running.
- Page 16 The Hayward, Pentair and Polaris controls use a 4 wire connection to communicate to the SwimPure Plus and can be wired up to 500' apart. Any outdoor rated 4 conductor cable can be used. Refer to each manufacturer's instructions and the wiring diagrams below for proper wiring connection to the SwimPure Plus.
- Page 17 SwimPure Plus control. Verify input voltage with a voltmeter. If there is input power, the fuse may have blown. The SwimPure Plus is protected by a 20 amp mini ATO fuse located on the circuit board above the cell connector.
- Page 18 - Salt level too high (High Salt LED on). - Very warm pools increase chlorine demand--increase Output %, or filter run time. - Cold water (below 50ºF) causes SwimPure Plus to stop generating (Generating LED flashing). - Excessive scaling on cell.
- Page 19 SwimPure chlorination products to be free of defects in materials and workmanship, under normal use and service, for a period of three (3) years. Hayward also warrants its Aqua Trol chlorination products to be free of defects in materials and workmanship, under normal use and service for a period of one (1) year.
- Page 20 200 - 400 ppm Add calcium to increase. Drain and add water to decrease. Electrolytic Cell inspect & clean Refer to section in manual. www.hayward.com Refer to for latest manual revisions, additional information and helpful service. 092099E RevG 620 Division St.