Advertisement
•
In particularly severe environmental conditions (large size
of the environment, high temperature or humidity outside,
poor insulation of the room, too many of people or strong
heat load in the room, strong exposure to the sun ...) this
device may not be able to reach the best comfort level.
SILENT FUNCTION (CAN ONLY BE ACTIVATED IN
LOCAL AIR CONDITIONER MODE) (fig. 17)
By activating this function in local air conditioner mode, the
noise level of the appliance is further reduced.
To activate, press the
The display shows the related indicator light (C12).
PROGRAMMING THE TIMER (fig. 18)
The timer allows for the delayed start up or shut down of the
appliance. This function will prevent wasting electricity by opti-
mising the operating periods.
How to program delayed start up
•
Plug in the appliance and set to standby.
•
Press the timer key (D8): the timer symbol (C15) and hours
light up.
•
Use the
(D4) or
until the appliance should start up.
•
The appliance will start to operate in the same operating
mode that was previously set.
Start up can be programmed at any time within the 24 hours
that follow. A few seconds after the timer is set, the setting is
acquired. The timer symbol stays lit and the display returns to
standby.
To cancel the timer program, press the timer key (D8) twice. The
timer symbol (C15) will go off.
How to program delayed shut down
•
While the appliance is on in any operating mode,
delayed shut down can be programmed.
•
Press the timer key (D8): The timer symbol (C15) and
hours light up.
•
Use the
(D4) or
hours until the appliance should shut down.
A few seconds after the timer is set, the setting is acquired, the
display shows the operating mode and the timer symbol stays
lit.
Once the set time is elapsed, the local air conditioner goes into
Standby. To cancel the timer program, press the timer key (D8),
twice. The timer symbol (C15) will go off.
(D7) key.
(D3) key to set the number of hours
(D3) key to set the number of
OPERATION USING THE REMOTE CONTROL
(See page 4 - D)
•
Aim the remote control at the receiver (A11) on the local air
conditioner. The maximum distance between the remote
control and the appliance is 5 metres with no obstacles
between the remote control and the receiver (fig. 19).
•
The remote control should be handled with extreme care,
without dropping it or exposing it to direct sunlight and
keeping it away from heat sources.
DESCRIPTION OF THE REMOTE CONTROL
D1. ON/STAND-BY button
D2. MODE button
D3. Decrease button
D4. Increase button
D5. Air flow
D6. Swing button
D7. Silent button
D8. Timer button
D9. ECO REAL FEEL button
SWING BUTTON
The SWING button (D6) moves the grille flap, evenly distributing
the air into the room.
When the SWING button is pressed, the flap will begin to move
forwards and backwards alternatively.
If pressed again, the flap will be locked into its current position.
When the button is next pressed, the flap will start to move
forwards and backwards again.
NOTE: in order to avoid damaging the internal mechanisms, the
flap must not be moved manually.
INSERTING OR REPLACING BATTERIES
•
Remove the cover on the back of the remote
•
Insert two LR03 "AAA" 1.5 V batteries in the proper position
(see the indications inside the battery compartment). If the
batteries are low, replace them with the same type.
•
Replace the cover.
When replacing or disposing of the remote control, the
batteries must be removed and disposed of according to
current legislation as they are damaging to the environ-
ment. Do not mix alkaline batteries, standard (zinc-car-
bon) batteries or rechargeable (nickel cadmium) batter-
ies. Do not throw the batteries in the fire as they could
explode or release hazardous liquids.
17
Advertisement
