Server EZT-S Manual
  1. Manuals
  2. Brands
  3. Server Manuals
  4. Dispenser
  5. EZT-S
  6. Manual

Server EZT-S Manual

Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

EZ-Topper
Short, Single
MODEL: EZT-S
WITH SPOUT HEATER:
85880 COMPLETE
85711 WARMER BASE
WITHOUT SPOUT HEATER:
85890 COMPLETE
85712 WARMER BASE
Used with a
48 fl. oz pouch
with 16mm
center fitment.
Thank You
For your purchase. This pouched topping
warmer virtually eliminates product degradation
and waste, so you can reduce food costs while
delivering a superior product.
SIMPLIFY TOPPING MANAGEMENT—GO POUCHED
™

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EZT-S and is the answer not in the manual?

Questions and answers

Related Manuals for Server EZT-S

Summary of Contents for Server EZT-S

  • Page 1 EZ-Topper ™ Short, Single MODEL: EZT-S WITH SPOUT HEATER: 85880 COMPLETE 85711 WARMER BASE WITHOUT SPOUT HEATER: 85890 COMPLETE 85712 WARMER BASE Used with a 48 fl. oz pouch with 16mm center fitment. Thank You For your purchase. This pouched topping...
  • Page 2 PARTS CARAMEL KNOB OPTIONAL: USE KNOBS TO 82023-024 QUICKLY IDENTIFY PUMP CONTENTS FUDGE KNOB 82023-015 EZ-TOPPER PUMP 85820 WARMER BASE WITH SPOUT HEATER 85711 (SHOWN) WITHOUT SPOUT HEATER 85712 Units 85880 & 85711 include MAGNETIC DECAL SET 84973 FOOT 07429 Page 2...
  • Page 3 Be aware of the product you are serving and the This unit must be earthed or grounded. temperature the product is required to maintain. Server Products, Inc. can not be responsible for the This requires all three prongs (terminals) on cord plug to be plugged into power source.

  • Page 4: Unit Setup

    WASH ALL PARTS PROPERLY UNIT SETUP BEFORE EVERY USE. See page 6. SEE SEPARATE PUMP MANUAL FOR PUMP SETUP. ATTACH PUMP TO POUCH • Place pouch on countertop with pouch fitment circle facing upward. • Position pump connector directly Pump is fully engaged when over center of pouch fitment.
  • Page 5 UNIT TAKE-DOWN PRESS SWITCH to the “OFF” position. UNPLUG CORD CAUTION- HOT Allow unit to cool before continuing or use proper care with hot surfaces. REMOVE PUMP WITH POUCH DETACH POUCH from bottom of pump. FLUSH AND RINSE PUMP Thoroughly rinse all inside and outside surfaces of pump with hot water.

  • Page 6: Care Of Stainless Steel

    CLEANING SEE SEPARATE PUMP MANUAL FOR PUMP INSTRUCTIONS. WARNING- ELECTRICAL SHOCK COULD OCCUR • Electrical components of unit could be damaged from water exposure or any liquid. • Never immerse unit into water or any liquid. • Never use any water jet or pressure sprayer on unit.

  • Page 7: Screw) Assembly

    WIRING UNITS 85711, 85712 | 120V | USA GROUND GROUND (USING STANDOFF STUD 10068 PIN VESSEL CONTROL SCREW) ASSEMBLY PANEL GREEN WHITE BLACK Cord Assembly Bushing/Strain Relief Snap-In Rocker Switch 6" Wire Assembly, Black Thermostat Heating Element 15" Wire Assembly, Green Page 7...

  • Page 8: Troubleshooting

    Allow unit to fully air dry. SERVER PRODUCTS GENERAL SERVICE, Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number.

This manual is also suitable for:

85880857118589085712Ez-topper ezt-s

Table of Contents