Optional Relays Required; Figure 5: Connecting D8132 Modules; Figure 6: Relays For Terminals 7 And 8 And Ground Start - Radionics D9000 Series Operation And Installation Manual

D 8132
1.4 Am ps
D 8132
1 .4 A m ps
The Radionics defaults set relay A (terminal 6)
as a Steady Alarm Bell output and relay A
(terminal 7) as a Pulsed Fire Bell output, and
relay C (terminal 8) as a Verification/Reset
output for smoke detectors. The D9000/D7000
Series Program Entry Guide (74-07695-000)
contains complete instructions for programming
relays. Descriptions of the functional
characteristics of each terminal appear on the
next page.
See the Bell Parameters section of the program
to set the Fire Bell, Alarm Bell output responses
for relays. Four annunciation patterns: Steady,
Pulsed, California Standard, and Temporal Code
3 are available.
Unexpected Output at Terminals 6, 7 and 8: If
terminals 6, 7, and 8 don't provide the output you
expect:
• Check the programming for relays A, B, and
C in the Relays module of the program.
Check the Bell Parameters section of the
•
program to verify the Alarm and Fire Bell
responses are programmed for the duration
and pattern you expect.
• Check the Point Assignments to verify each
point is programmed for the local response
you expect.
74-07692-000-C
www.PDF-Zoo.com
LEDs Off When Normal
YE L
Charging Status
RED Low Battery
C L A S S 2 TR A N S FO R M E R
1 1 6 . 5 VA C 4 0 VA 6 0 H Z
P ar t N o . D 1 6 4 0
I n t e rn a lly F u se d - D o N o t S h o r t
R e q u ire s U n sw itc h e d O u t le t
2
D o N o t S h a re W it h Ot h e r E q u ip m e n t
+ AUX POWER
3
(+ ) 3
BATTERY NEGATIVE O NLY
4
M ax imum Charging
4
(-) C urrent 1.4 Am ps.
5
BATTERY POSITIVE ON LY
PROGRAMMABLE
STEADY O R
6
+
ALARM OUTPUTS
PULSE
T erminals
7
+ ALTER NATE
7 & 8
Require
Optional
SW ITC HED
8 D136 Relay
+
(+ ) 8
AU X POW ER
in J1 & J9
9 9 CO MMON
(-)
10 EART H GROU ND
PH ON E MONITOR SELECT
Loop Start
Ground Start
TELCO
GROUN D
COR D
PHONE
START
RE D
LED
Requires
Relay
O N W HEN
#D136
C O M MU NI CA TI NG
O F F W H EN I DLE
NOTE: C om b ined To tal D isp ers ed
C urrent of 7.0 a m p s @ 12 V D C

Figure 5: Connecting D8132 Modules

D9000/D7000 Series Operation & Installation Manual
4/97
firealarmresources.com
1 .4 Am ps
VOLTAGE R ANGES
O N-BOARD POIN TS
Open 3.7 - 5.0VD C
Ω
1.0K R esistor
Norm al 2.0 - 3.0VDC
R equired at End o f Line
Short 0.0 - 1.3VDC
Poin t 1 Point 2 Point 3 Point 4 Poin t 5 Point 6 Point 7 Point 8
11
1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 20 2 1 22

Optional Relays Required

Install an optional D136 plug-in relay into socket
J1 to enable the output at terminal 7. Install a
D136 in socket J9 to enable the output at terminal
8. The relay sockets are under the faceplate as
shown in Figure 6.
TOP
L
E
F
T
BO TTOM
Figure 6: Relays for Terminals 7 and 8
Page 19
17-05823-002
Operation Monitor
Pulses When Normal
GR N
Flickers When Ringing
Reset Pin
Disable All Except Battery
Charging And Programming
PER IPHERAL DEVIC E WIRIN G
POW ER + 32
RED
(+ )
32
YELLO W DATA BUS A 31
D 8132
GR EEN DATA BU S B 30
1 .4 A m p s
BLACK C OM M ON 29
(-)
29
N.F.P.A.
28
Style 3.5 ZONEX OUT 1
Signaling
Line
Circuits
ZO NEX IN 1 27
26
ZONEX OUT 2
25
ZO NEX IN 2
D 8132
ZON EX POWER + 24
(+ )
24
1 .4 A m p s
ZONEX COMM ON 23 (-)
23
PROG
CONN
NO TE : T he D 136
relays are ins erted
with the three pins
M
Arom at
DS2 E-M-DC 12 V
on the top side.
M
Arom at
DS2 E-M-DC 12 V
J
M
Aromat
DS2E-M- DC12V
GND START
and Ground Start
K 3/
J1
K1/
J9
K 6/
J5