Radionics D9000 Series Installation And Troubleshooting Quick Reference
Control/communicator
Hide thumbs
Also See for D9000 Series:
- Operation and installation manual (67 pages) ,
- Installation and troubleshooting quick reference (14 pages)
Table of Contents
Advertisement
Quick Links
Installation and Troubleshooting Quick Reference
Introduction
33317D 4/97
www.PDF-Zoo.com
D9000/D7000 Series Control/Communicator
This reference contains the very basic information a trained installer needs to install and
troubleshoot a D9000/D7000 Series Control/Communicator system. See the D9000/D7000
Series Operation and Installation Manual (74-07692-000) and the D9000/D7000 Series
Approved Applications Compliance Guide (74-07693-000) for a complete description of the
D9000/D7000 Series Control/Communicator and detailed installation instructions.
Basic Troubleshooting ............................................................. 2
Service Walk Test Shows Extra Points ................................ 2
Problems with Points ............................................................ 4
Problems Programming the Panel ........................................ 7
Phone Line Trouble ............................................................... 8
Communications Failure ....................................................... 8
System Wiring Diagrams, Issue A ......................................... 10
D9412 Control/Communicator ............................................. 10
D9112 Control Communicator ............................................. 11
D7412 Control/Communicator ............................................. 12
D7212 Control/Communicator ............................................. 13
Quick Reference Terminal Description .................................. 14
firealarmresources.com
Advertisement
Table of Contents
Related Manuals for Radionics D9000 Series
Summary of Contents for Radionics D9000 Series
-
Page 1: Table Of Contents
D9000/D7000 Series Control/Communicator Installation and Troubleshooting Quick Reference Introduction This reference contains the very basic information a trained installer needs to install and troubleshoot a D9000/D7000 Series Control/Communicator system. See the D9000/D7000 Series Operation and Installation Manual (74-07692-000) and the D9000/D7000 Series Approved Applications Compliance Guide (74-07693-000) for a complete description of the D9000/D7000 Series Control/Communicator and detailed installation instructions. -
Page 2: Basic Troubleshooting
Basic Troubleshooting Service Walk Test Shows Extra Points The Service Walk Test differs from the standard Walk Test in that POPITs whose switches are set for a point number not programmed in the panel appear in the test. Service Walk Test only available at Command Centers with panel wide scope: See Command Center in the D9000/D7000 Series Control/Communicator Program Entry Guide (74-07695-000) for a description of Command Center scope. - Page 3 SE RV IC E WA LK ? E N T 246 P TS TO TES T Test a d evice P O IN T TE XT (Text d isplays 60 se co nds) 2 45 PT S TO TE ST Test a d evice PO IN T T E XT (Text d isplays 60 se co nds)
-
Page 4: Problems With Points
Problems with Points If you incorrectly set the switches on a POPIT you may create both a missing and extra point. When you find a missing point, perform a Service Walk Test to search for extra points. See the Owner’s Manual (71-06150-000) for test instructions. Symptom Diagnosis Remedy... - Page 5 Problems with Points (Continued) Symptom Diagnosis Remedy One or more The sensor loop is Remove the sensor loop from the points remain in open, shorted, or D9412/D9112 or POPIT and meter it for trouble or alarm grounded. continuity. There should be no more than with all devices 100 ohm resistance, plus the value of the Opens,shorts, or...
- Page 6 Problems with Points (Continued) Symptom Diagnosis Remedy All off-board Short on Aux Power, Terminals 3 and 24 share a common circuit points are terminal 3 or ZONEX breaker. Check wiring and devices connected MISSING. power, terminal 24. to these terminals for shorts or grounds. If only one POPEX Check POPEX module for correct connections module is connected...
-
Page 7: Problems Programming The Panel
Problems Programming the Panel Before attempting to program the panel, you should be familiar with the basic operation of the D5200 programmer. See the D5200 Operation Manual (74-06176-000). If you still experience problems, check for the symptoms below. Symptom Diagnosis Remedy The programmer The programmer is... -
Page 8: Phone Line Trouble
Verify that the receiver is compatible answers the call compatible with the with the format the D9412 is using and provides an D9412/D9112 (either BFSK or Radionics Modem initial “handshake” transmission format. IIIa ™ Communications Format). See Phone in the D9412/D9112 Program acknowledgment, Entry Guide (74-07695-000). - Page 9 Communications Failure (Continued) Symptom Diagnosis Remedy The line rings but Line is not ringing at 1. Verify that the lines are correctly the D6500 the receiver. connected to the receiver. receiver does not 2. Verify that correct prefixes and phone pick up.
-
Page 10: System Wiring Diagrams, Issue A
D9210B ACCESS CONTROL INTERFACE D8004 TRANSFORMER D122 DUAL UP TO EIGHT ENCLOSURE. BATTERY HARNESS REQUIRED FOR NFP A SUPERVISED APPLICATIONS. ARMING STATION D1255 D126 D126 D9131A PARALLEL REQUIRED BATTERY UP TO EIGHT BATTERY 17-0 582 3- 00 2 PARALLEL SUPERVISED PRINTER 12V 7Ah D1640... -
Page 11: D9112 Control Communicator
D8004 TRANSFORMER D122 DUAL ENCLOSURE. BATTERY HARNESS REQUIRED FOR NFPA APPLICATIONS. ARMING STATION D1255 D126 D126 D9131A PARALLEL REQUIRED BA TTERY UP TO EIGHT BATTERY 1 7-0 582 3- 002 SUPERVISED PRINTER 12V 7Ah D1640 12V 7Ah D 9112 LEDs Off When Normal INTERFACE YE L O p e ra tion M o n itor... -
Page 12: D7412 Control/Communicator
D9210B ACCESS CONTROL INTERFACE D8004 TRANSFORMER D122 DUAL UP TO EIGHT ENCLOSURE. BATTERY HARNESS SUPERVISED REQUIRED FOR NFPA APPLICATIONS. ARMING STATION D126 D1255 D126 D9131A PARALLEL REQUIRED BA TTERY BATTERY 1 7- 058 23 - 0 02 UP TO EIGHT PRINTER 12V 7Ah SUPERVISED... -
Page 13: D7212 Control/Communicator
D8004 TRANSFORMER D122 DUAL ENCLOSURE. BATTERY HARNESS REQUIRED FOR NFP A APPLICATIONS. ARMING STATION D1255 D126 D126 D9131A PARALLEL REQUIRED BATTERY UP TO EIGHT BATTERY 17 -05 82 3- 0 02 PRINTER SUPERVISED 12V 7Ah D1640 12V 7Ah D 7212 L EDs Of f When Normal INTERFACE Op er ati on M o nit or... -
Page 14: Quick Reference Terminal Description
32 (+) POWER + affected by shorts on any other terminal. ™ The Radionics logo is a registered trademark of Radionics © 1997 Radionics, Inc., Salinas, CA, USA. All rights reserved. Radionics, Inc., PO Box 80012, Salinas, California 93901-0012 www.PDF-Zoo.com...