Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hi-Touch Imaging Technologies Mug Heat Press Kit
Summary of Contents for Hi-Touch Imaging Technologies Mug Heat Press Kit
-
Page 1: User Manual
HiTi Photo Printer Mug Heat Press Kit User Manual... - Page 2 COPYRIGHT The information contained in this document is subject to change without notice. Hi-Touch Imaging Technologies makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 SAFETY INSTRUCTIONS 1. Read these instructions carefully. reference. Follow all warnings and instructions marked on the product. 2. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3.
- Page 4 installation. If these equipment doses cause harmful interference to radio or television reception, which can be determined by interference by on or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3.
-
Page 7: Chapter 1. Welcome
Chapter 1. Welcome Our Invitation to HiTi Photo Printer Family It is our pleasure to have you onboard as the member of HiTi Photo Printer family. We thank you for your patronage and hope this is just the beginning of our long-term ssociation. -
Page 8: Other Features
2-2 Other Features Professional Locating coil design ,accurate for locating.Dual temperature sensor and plastic cover design, secure and accurate for useAutomatic power-off design while abnormal activities appearBundled software , MugDesiree ,to provide solution for Mug personalization... -
Page 9: Chapter 2 Mugdesiree Introduction
Chapter 2 MugDesiree Introduction 2-1. Mug Desiree Installation: To Install: 1. Insert MugDesiree CD into CD-ROM 2. If CD-ROM does not auto start, please click 3. Click OK. Follow the instructions on the screen. To start 1. Click Start/Programs. Go to the HiTi folder, select the Start/Run and type D:\SETUP.EXE (where “D”... -
Page 10: Operation Procedure
2-2. Operation Procedure 1. Select Start\Programes\HiTi\HiTi\HitiMug\ MugDesiree or double-click to run MugDesiree 2. Press button and import the images from computer 3. Press button and import images from HiTi printer 4. Press button and import templates from computer. You can edit the template format such as rotate, color setting as the step 10-14. - Page 11 （a）99mm x 74mm Or you can edit your own layout format as in illustration (d) 8. After picking desire print layout, press image/templates into designated picturing area. 9. The edit area is composed of three different layers, image , template and text layer, which could be edited separately.
- Page 12 —Text layer 10. Use , and /template within picturing area. Fits the image /template vertically to the height. Fits the image /template horizontally to the width. Prompts an image/template size window for user to custom defines width, length, and pixel. 11.
- Page 13 ---Portrait, this will enhance the imprinted people image on the mug. ---Landscape, this will increase the color saturation imprinted on the mug. ---Artistic, this will double the color saturation imprinted on the mug. "Artisitc' effect is good if image is text or logo. ---Normal, the imprinted image on the mug is the same as the original image.
-
Page 14: Chapter 3 Mug Heat Press
Chapter 3 Mug Heat Press Standard Operation Procedure 1. You should have the following tools in hand: Mug Heat Press, Bubble Eliminator, White Ceramic Mug, Mug Locating Tape, Dye Sublimation Photograph, Mug Locating Coil, Clean Towel (recommend polyester fabric),a pair of gloves and a bottle of methane, 2. - Page 15 Useful Tips: (1). Carefully cutting off excessive margin on top of photography (2). Place mug inside locating coil.The bottom of the mug should be in parallel with locating coil (3). Left and right side of photograph should be in parallel with the edge of locating coil (4).
- Page 16 Useful Tips: (1). Ensure no gap between photography and mug while using bubble eliminator to squeeze out air pocket (2). Tape the mug when bubble eliminator (3). Use finger to press the wrinkle while wrinkle appears during air pocket removing. 8.
- Page 17 11. Flip down the plastic cover 12. Select <RUN> and press OK, an the default setting would be applied for the heating process (the default pre-heating time/temperature is 1 min/ C and the default heating time/temperature is 4 min/ 150 also select <Setting>...
- Page 18 14. Push the adjustor to tight on the mug against the plastic roller. With hand holding the mug holder, rotate the mug counter-clockwise and clockwise to squeeze any air between the mug and the photo. Useful Tips: (1). Start to bubble elimination process immediately after pre-heating process in order to have the best result (2).
- Page 19 18. Wait until the temperature of mug cools down, then remove the mug locating tape. Useful Tips: (1). Peel the photo off immediately while heating completed, can get ultimate output. (2). Avoid burning from touching, please wear glove. (3). Avoid double-image, don’t stick the photo on the mug again. (4).
-
Page 20: Chapter 4 Consumable Replacement
Chapter 4 Consumable Replacement 4-1 Heater Plate Replacement 1 Turn off the power and wait for 20 minutes for machine to cool down 2 Take out the white teflon and black rubber 3. Pull the heater plate from machine, you will see a semi- sphere hole where a wire is connecting with heater plate. - Page 21 5. Make sure the wire and the new heater plate is properly reconnected. 6. Put the connector through the semi-sphere hole and put the heater plate into the original location. Then put the black rubber and white Teflon onto the machine. Make sure the heater plate , black rubber and white silicon are wrapped by white Teflon.
- Page 22 4-2. Teflon Replacement // The white Teflon on the surface of the heater plate is used for improving the image transferring effect onto the mug. If you find any cracks on the surface of the Teflon, please contact your local distributor and replace the Teflon according to the following procedure. // 1.
- Page 23 Cover the white, orange and black components. 5. Insert the Teflon into the embracer as the following illustration. Push it 6. The new Teflon replacement is completed.
-
Page 24: Chapter 5 Useful Tips For Mug Heat
Chapter 5 Useful tips for Mug Heat Machine Maintenance Erros Message displays on COVER OPEN OVER HEAT ADC FAILS TC0 FAILS TC1 FAILS TCx FAILS NO MUG TIME UP If you are still unable to make the machine function properly, please contact local distributor or regional HiTi offices, Region E-mail...