Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DMP Electronics Com Series
Summary of Contents for DMP Electronics Com Series
- Page 1 HOW-TO GUIDE: ECP PASSTHRU...
-
Page 2: Table Of Contents
TABLE OF CONTENTS ECP Passthru Overview ..................1 Procedure ................................1 Required Materials ............................1 Step 1: Mount the Communicator ................. 2 Step 2: Wire the Communicator ................2 Step 3: Program the Vista Keypad ............... 4 Step 4: Configure ECP Settings ................4 Remotely (Dealer Admin) .......................... -
Page 3: Ecp Passthru Overview
Ethernet (DualCom only) Tamper LOAD RESET +DC- Z1 Z2 Z3 G +Z4- O1 O2 +DC- Z1 Z2 Z3 G +Z4- O1 O2 CellCom or DualCom Figure 1: CellCom and DualCom Components COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 4: Step 1: Mount The Communicator
Model 330-24V programming harness with an in-line resistor. 4. After programming is complete, remove the keypad and replace the housing cover on the mounted base. Note: Address 1 is reserved by the system for programming keypads. COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... - Page 5 12 13 14 15 16 17 18 19 20 21 22 23 24 25 RING RING – (BROWN) (GRAY) (GREEN) (RED) From DC– From DC+ From Z4- From Z4+ Figure 2: ECP Wiring COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS...
-
Page 6: Step 3: Program The Vista Keypad
9. Press Begin. 10. After setup is complete, Dealer Admin automatically retrieves zones from the host panel. If you need to retrieve zones again later, open System Options and select Get Zones. COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 7: Locally (Keypad)
The ECP panel could not be Wait and retry programming or reduce traffic on the programmed due to high ECP bus ECP bus, then retry programming. traffic. Table 2: Programming Messages and Troubleshooting COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 8: Step 5: Remote Programming
5. Go to File > Panel Information. 6. In Connection Information, enter the VISTA account number in Ecp Acct. Press OK. 8. Go to ECP Passthru > ECP Start/Stop Server. 9. Minimize Remote Link. COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 9: Add The Vista Panel In Compass
3. In Subscriber Data, enter a Receiver number and Account number. 4. In the Panel Data section, select the VISTA panel model and revision number. 5. In Network Device MAC Addr, enter FFFFFF. 6. Press OK. COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 10: Set Up Communication In Compass
4. Select TCPIP Port Settings. 5. To ensure that Compass uses a TCP/IP connection, select a TCP/IP port. 6. Press Add. Back in Communication Settings window, select Apply. 8. Press OK. COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 11: Configure Tcp/Ip Settings In Compass
4. In the TCPIP Port dropdown, select the appropriate TCP/IP port. 5. Ensure that the Network Device MAC Addr is FFFFFF. 6. In Connection Mode, select ECP. Ensure that AlarmNet-i is selected. 8. Press Connect. COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 12: Reference
To use Virtual Keypad for remote management, the configuration must meet the following conditions: • ECP Panels must be programmed as Stay/Away for remote arming and disarming (No Partitions). COM SERIES HOW-TO GUIDE: ECP PASSTHRU | DIGITAL MONITORING PRODUCTS... -
Page 13: Vista Panel Compatibility
VISTA Panel Compatibility Remote Remote Remote Compatible with Panel Type User Management Arming/Disarming Zone Status Compass VISTA-10SE Rev 15 or higher Firmware version VISTA-10P 2.0 or higher VISTA-15 Firmware version VISTA-15P 5.2 or higher VISTA-20SE Rev 12 or higher Firmware version VISTA-20P 5.2 or higher Firmware version...
Need help?
Do you have a question about the Com Series and is the answer not in the manual?
Questions and answers