Kipp & Zonen DustIQ Instruction Sheet

DustIQ - instruction sheet
1/4
During indoor pre-installation follow the instruction in the manual
Follow these instructions
carefully for the correct
mechanical and electrical
installation of the DustIQ
Requirements
only for
pre-install
indoor
use
Allen key 6 mm USB to RS-485 converter
Cable connection
Wire Function Connect with
Yellow Modbus ® RS-485 Data +
Data -
Grey Modbus ® RS-485
White Power 12 to 30 VDC
Black Power ground
Blue Modbus common / Ground Ground
®
Shield Housing Ground*
* Connect to ground if DustIQ is not grounded
Push-Pull Connect the supplied cable to the socket labelled 'Host'
Daisy Chain -or- Temperature Sensor
Host
Sensor 2
Optional
Spanner 13 mm
Default
Prefered installation
Modbus baud rate
®
19200
Data bits
8
Parity
even
Stop bits
1
Address
1
Factory dust profile
Common desert dust
Calibration
Solar Panel
Sensor 1
Delivered Contents
Delivery Contents Specifications
DustIQ - instruction sheet
Follow these instructions for part number 0386900 During indoor pre-installation: DustIQ - quick start guide Delivery Contents Specifications
carefully for the correct Do not turn on the power of the DustIQ unit only for Requirements indoor use pre-install Positions and options 10 meter 4x 4x 4x 4x 8x Dimensions 4 kg -4°F to 140°F -20°C to 60°C IP 65 40 mm
mechanical and Do not connect the DustIQ unit to a computer Do not turn on the power of the operating computer until instructed to Cable connection Yellow White Grey Blue Black Function Shield Modbus® RS-485 Modbus® RS-485 Power ground Power 12 to 30 VDC Modbus® common / Ground Housing Allen key 6 mm Wire USB to RS485 converter A/A`/- computer until instructed to do so Address Ground B/B`/+ even Do not turn on the power of the operating Stopbits 19200 Parity During indoor pre-installation: Local dust profile Modbus® baud rate Spanner 13 mm Default Ground* Connect with Do not connect the DustIQ unit to a computer Do not turn on the power of the DustIQ unit This side up 1 1 Installed vertically Prefered installation PV panel PV panel (35 mm) PV panel PV panel DustIQ (40 mm) DustIQ DustIQ (40 mm) PV panel (35 mm) PV panel (40 mm) (40 mm) (35 mm) (40 mm) (40 mm) IP 65
electrical installation of do so meter 10 Push-Pull * Connect to ground if DustIQ is not grounded Connect the supplied cable to the socket labelled 'Host' Arizona test dust 90 mm 40 160 mm 4x 4x 4x 4x 8x 4 kg -20 °C to 60 °C -4 °F to 140°F
the DustIQ
Requirements Positions and options Dimensions
pre-install only for
indoor use 35 mm
Allen key 6 mm USB to RS485 converter Spanner 13 mm
Cable connection Default Installed vertically Prefered installation
This side up PV panel DustIQ PV panel
Wire Function Connect with Modbus® baud rate 19200 40 mm 35 mm 40 mm
Yellow Grey Modbus® RS-485 Modbus® RS-485 Data + Data - even Parity
White Power 12 to 30 VDC Stopbits 35 mm 35 mm 35 mm
Black Power ground Address 1
Blue Shield Housing Modbus® common / Ground Ground Ground* 1
* Connect to ground if DustIQ is not grounded Arizona test dust Local dust profile
Push-Pull Connect the supplied cable to the socket labelled 'Host'
Daisy Chain -or- Temperature Sensor Calibration
Host Solar Panel
Sensor 2 Sensor 1
35
90 mm 160 mm
10
4x
meter
Positions and options
PV panel DustIQ PV panel
40 mm 35 mm 40 mm
35 mm 35 mm 35 mm
Specifications
-20 °C to 60 °C
4x 4x 4x 8x 4 kg -4 °F to 140°F
Dimensions
90 mm 90 mm
IP 65
35 mm
35
160 mm 160 mm