Furuno UAIS TRANSPONDER FA-150 Installation Manual
  1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Marine Radio
  5. FA-150
  6. Installation manual

Furuno UAIS TRANSPONDER FA-150 Installation Manual

Uais transponder
Hide thumbs Also See for UAIS TRANSPONDER FA-150:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual , Installation Manual
SAFETY INSTRUCTIONS .....................................................................................................................I
SYSTEM CONFIGURATIONS..............................................................................................................ii
EQUIPMENT LISTS ............................................................................................................................iii
1. MOUNTING ......................................................................................................................................1
1.1 Antenna Units............................................................................................................................1
1.2 Monitor Unit...............................................................................................................................8
1.3 UAIS Transponder...................................................................................................................10
1.4 Power Supply (option).............................................................................................................11
1.5 Pilot Plug (option)....................................................................................................................11
2. WIRING...........................................................................................................................................12
2.1 Connection ..............................................................................................................................12
2.2 Changing Ship's Mains Specifications ....................................................................................16
3. SETTING AND ADJUSTMENT ......................................................................................................17
3.1 Inland AIS Specific Settings ....................................................................................................17
3.2 Setting MMSI, IMO No., Name and Call Sign .........................................................................20
3.3 Setting GPS Antenna Position ................................................................................................21
3.4 Setting Ship Type ....................................................................................................................22
3.5 Setting I/O Port........................................................................................................................22
4. ATTACHING LAN KIT (OPTION) ...................................................................................................27
5. IEC 61162-1/2 DATA SENTENCES................................................................................................31
APPENDIX 1 JIS CABLE.............................................................................................................. AP-1
PACKING LISTS...............................................................................................................................A-1
OUTLINE DRAWINGS .....................................................................................................................D-1
INTERCONNECTION DIAGRAM..................................................................................................... S-1
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Installation Manual

UAIS TRANSPONDER

www.furuno.co.jp
FA-150

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UAIS TRANSPONDER FA-150 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Furuno UAIS TRANSPONDER FA-150

Summary of Contents for Furuno UAIS TRANSPONDER FA-150

  • Page 1: Table Of Contents

    5. IEC 61162-1/2 DATA SENTENCES...31 APPENDIX 1 JIS CABLE... AP-1 PACKING LISTS...A-1 OUTLINE DRAWINGS ...D-1 INTERCONNECTION DIAGRAM... S-1 All brand and product names are trademarks, registered trademarks or service marks of their respective holders. Installation Manual UAIS TRANSPONDER www.furuno.co.jp FA-150...
  • Page 2 : +81-(0)798-65-4200 Printed in Japan All rights reserved. Pub. No. IME-44310-E1 (DAMI ) FA-150 The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer A : NOV E1 : MAR . 23, 2011 *00015008314* *00015008314* *00015008314* *00015008314*...

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS The installer must read the safety instructions before attempting to install this equipment. WARNING CAUTION Warning, Caution WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment unless totally familiar with electrical circuits and service manual. Only qualified personnel should work inside the equipment.

  • Page 4: System Configuration

    SYSTEM CONFIGURATION Either GPS antenna VHF antenna GSC-001 GPA-017S UAIS TRANSPONDER FA-1501 Power supply PR-240 24 VDC 100-115/ 200-230 VAC 1φ, 50/60Hz Category of the units GSC-001 Exposed to the weather GPA-017S Exposed to the weather GVA-100 Exposed to the weather FA-1501 Protected from the weather FA-1502...

  • Page 5: Equipment Lists

    EQUIPMENT LISTS Standard supply Name UAIS Transponder Monitor Unit GPS Antenna GPS/VHF Combined Installation Materials Accessories Spare Parts Type Code no. FA-1501 FA-1502 GSC-001 GPA-017S GVA-100 MJ-A10SPF0012-050 000-150-216 CP24-00501 005-955-550 CP24-00400 000-041-980 CP24-00101 005-950-730 CP24-00141 005-952-330 CP24-00502 005-955-560 FP14-02801 004-366-960 SP24-00101 Remarks Select one.
  • Page 6 Optional supply Name Monitor unit Antenna cable set Antenna cable set Coaxial cable Mast mount fixture Right-angle antenna base L-angle antenna base Antenna base for rail mount Whip antenna Antenna fixing bracket Whip antenna AC-DC power supply Pilot plug AD-100 Cable assy.

  • Page 7: Mounting

    1. MOUNTING Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. 1.1 Antenna Units 1.1.1 GPS antenna unit Install the GPS antenna unit referring to the drawing on page D-5 or D-6 at the back of this manual.
  • Page 8 How to attach the connector N-P-8DFB for cable 8D-FB-CV Dimensions in millimeters. Outer Sheath Armor Inner Sheath Shield Cover with heat-shrink tubing and heat. Clamp Gasket (reddish brown) Trim shield here. Insulator Trim aluminum tape foil here. Clamp Nut Solder through the hole.

  • Page 9: Vhf Antenna

    1.1.2 VHF antenna Location The location of the mandatory AIS VHF-antenna should be carefully considered. Digital communication is more sensitive than analog/voice communication to interference created by reflections in obstructions like masts and booms. It may be necessary to relocate the VHF radiotelephone antenna to minimize interference effects.
  • Page 10 Horizontal separation distance Whip antenna for AIS (GPS/VHF combined antenna) Vertical separation distance More than 2.8 m More than 0.5 m • When coaxial cable RG-10/UY (shipyard supply) is used, attach the coaxial plug M-P-7 (dockyard supply) as shown on the next page. Other VHF whip antenna More than 10 m...
  • Page 11 Lay the coaxial cable and attach an M-type plug (if necessary) to the cable as follows. 1. Remove the sheath by 30 mm. 2. Bare 23 mm of the center conductor. Trim braided shield by 5 mm and tin. 3. Slide coupling ring onto cable. 4.
  • Page 12 Mounting procedure 1. Dismount the bottom cover, cut the cable-tie inside the unit and take out the coaxial connector attached to the combined box. 2. Loosen four screws to loosen whip antenna fixture and pull out the coaxial connector coming from the combined box through the hole in the whip antenna fixture.
  • Page 13 Installing distributor unit DB-1 The length of the cable between the distributor unit and transponder unit is 1 m so locate the distributor unit within 1 m from the transponder unit. Fix the distributor unit on the bulkhead, facing the cable entrance downward. Remove the lid of the distributor unit and secure the unit with two self-tapping screws.

  • Page 14: Monitor Unit

    1.2 Monitor Unit The monitor unit can be installed on a desktop or flush mounted in a panel. Install it on the chart table or near the steering place, referring to the outline drawing. When selecting a mounting location for the monitor unit, keep the following in mind: •...
  • Page 15 Use the optional flush mount kit OP20-29. Name Type Cosmetic panel 20-016-1051 Self-tapping screw 5x20 Hexagon-head bolt M6x12 Spring washer 1. Prepare a cutout in the mounting location whose dimensions are 183 (W) x 92 (H) mm. 2. Attach the cosmetic panel (20-016-1051) to the unit with two hex head bolts (M6x12) and two spring washers (M6).

  • Page 16: Uais Transponder

    1.3 UAIS Transponder Mount the transponder, where it is protected from rain and water splash. This unit can be installed on a bulkhead. Install it, referring to the outline drawing. When selecting a mounting location for the transponder, keep the following in mind: •...

  • Page 17: Power Supply (Option)

    1.4 Power Supply (option) When selecting a mounting location for the unit, keep the following in mind: • Keep the unit out away from areas subject to water splash. • Locate the unit away from exhaust pipes and vents. • The mounting location should be well ventilated. •...

  • Page 18: Wiring

    2. WIRING 2.1 Connection Connect the equipment, referring to the interconnection diagram at the back this manual. GPS Antenna GSC-001 or GPS-017S 150M-W2VN or FAB-151D 0.6 m RG-10U/Y 8D-FB-CV, 30 m/50 m: Option RG-10U/Y: Local supply Power Supply PR-240 IV-1.25sq DPYC-1.5** 100/110/115/200/ 220/230 VAC...
  • Page 19 EXT ALM: Connect ship's alarm system. DC (-) DC (+) Internal ports of the Transponder COM1: Long range communication device (Inmarsat C, etc.) or External display (Radar, ECDIS, Pilotplug) COM2 & COM3: External display, NAVNET 2, Pilot plug COM4-COM6: GPS, Gyrocompass, Speedlog, ROT, etc. Blue Sign: Connects a Blue Sign device, a lighting device mounted on the bridge which gives off a blue light to warn oncoming vessels when your vessel is navigating a channel in the reverse direction.
  • Page 20 *: Waterproofing connectors Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with a cable-tie. **: DPYC-2.5, TTYCS-1Q and TTYCS-4 are Japan Industry Standard cables. Use them or the equivalents, referring to the Appendix. Cable connection at transponder Fabrication of cables TTYCS-4, TTYCS-1Q and TTYCS-1 Shield L: Depends on equipment connected.
  • Page 21 How to attach wires to the WAGO connector Wiring for WAGO connector Press downward. Terminal opener Wire WAGO connector Twist Procedure 1. Twist the cores. 2. Press the terminal opener downward. 3. Insert the wire to hole. 4. Remove the terminal opener. 5.

  • Page 22: Changing Ship's Mains Specifications

    Changing Ship’s Mains Specifications The AC-DC power supply PR-240 is shipped ready for connection to a 200-230 VAC ship’s mains. If the ship’s mains is 100 VAC-115 VAC, change the tap connection and terminal board connection as below. Attach label supplied as accessories to the front panel according to the ship’s mains.

  • Page 23: Setting And Adjustment

    3. SETTING AND ADJUSTMENT After installing the equipment, set up the own ship’s static information (MMSI, IMO number, ship’s name, call sign, type of ship and GPS antenna position). Also, set up the I/O ports. Inland AIS Specific Settings This section shows how to activate and set up the Inland AIS feature. (If you do not require this feature, go to section 3.2.) The installer obtains the AIS activation key from the place of purchase.

  • Page 24: Selecting Ais Mode

    Selecting AIS mode The Inland AIS has two operating modes: Inland (inland waterways) and SOLAS (SOLAS compliant class A AIS transponder). Select INLAND AIS mode as follows: 1. Press the [NAV STATUS] key to open the NAV STATUS menu. NAV STATUS menu (initial sub-menu) 2.
  • Page 25 FURUNO dealer. 4. Select SET BLUE SIGN SW then press the [ENT] key. SET BLUE SIGN SW sub-menu 5. NOT AVAILABLE is selected; press the [ENT] key. 6. Select NOT AVAILABLE (not in use) or AVAILABLE (in use) as applicable then press the [ENT] key.

  • Page 26: Setting Mmsi, Imo No., Name And Call Sign

    3.2 Setting MMSI, IMO No., Name and Call Sign 1. Display the INITIAL SETTINGS menu referring to step 1-3 in "Setting blue sign status" on page 18 - 19. [INITIAL SETTINGS] SET MMSI SET MMSI SET INT ANT POS. SET EXT ANT POS. SET SHIP TYPE SET I/O PORT SET BLUE SIGN SW...

  • Page 27: Setting Gps Antenna Position

    3.3 Setting GPS Antenna Position 1. Open the INITIAL SETTINGS window, referring to step 1-3 in "Setting blue status" on page 18 - 19. 2. Press ▲ or ▼ key to choose SET INT ANT POS. and press the [ENT] key. 3.

  • Page 28: Setting Ship Type

    3.4 Setting Ship Type 1. In the INITIAL SETTINGS window, press the ▲ or ▼ key to choose the SET SHIP TYPE and press the [ENT] key. 2. Press the [ENT] key and set number for ship type by using ▲ or ▼ key, referring to the table below.
  • Page 29 COM6. If you chose COM1, for example, do as follows. 4. Press the [ENT] key to display the COM1 setting window. 5. Press the [ENT] key again to display the MODE setting window. 6. Press ▲ or ▼ to choose the device connected and press the [ENT] key. LONG RANGE: Long range communication device, for ex.
  • Page 30 SENSOR: GPS, Gyrocompass, Speedlog, ROT, etc. HI LEVEL IF: NAVNET 2 STANDARD (PC port): PC for inputting NMEA data (Same data as EXT DISPLAY). MONITOR (PC port): PC having the FURUNO software FAISPC MK-2. SERVICE (PC port): Service use FAISPC MK-2-equipped PC. Format/Rate (SPEED)
  • Page 31 Priority setup 1. Press ▲ or ▼ to choose SET PRIORITY at the SET I/O PORT sub-menu and press the [ENT] key. 2. "L/L, COG, SOG" is selected; press the [ENT] key. 3. COM4 is selected; press the [ENT] key to display the setting window. 4.
  • Page 32 Quality setup (Inland AIS only) If your speed, course or heading sensor is type approved, choose quality setting as shown below. 1. Press▼ to choose SET QUALITY at the SET I/O PORT sub-menu then press the [ENT] key. 2. Press ▲ or ▼ to choose SPEED, COURSE or HEADING then press the [ENT] key.

  • Page 33: Attaching Lan Kit (Option)

    4. ATTACHING LAN KIT (OPTION) To connect to PC network or NAVNET 3D network, the optional LAN kit is required. Name: LAN kit Type: OP24-8 Code no.: 005-956-020 Name 1 NET100 board 2 Hex. spacer Attaching 1. Dismount the bottom cover. 2.
  • Page 34 Setting LAN port for PC network 1. Press the [MENU] key, choose INITIAL SETTING, enter password, choose SET I/O PORT and press the [ENT] key to show the SET I/O PORT sub menu. 2. Press ▲ or ▼ to choose SET LAN PORT and press the [ENT] key. 3.
  • Page 35 the [ENT] key. (Setting range: 000.000.000.000 to 255.255.255.255) 5. Press the [ENT] key, enter port number in the NAVNET PORT NO. field and press the [ENT] key. (Setting range: 10000 to 30000) 6. Press▼ to show next page. 7. Press the [ENT] key, enter gateway address in the GATEWAY ADDRESS field and press the [ENT] key.
  • Page 36 This page intentionally left blank.

  • Page 37: Iec 61162-1/2 Data Sentences

    5. IEC 61162-1/2 DATA SENTENCES IEC 61162-1/2 format data is input or output from the data port COM1-COM6. The table below shows the input/output data specifications. Transponder Port Menu setting LONG RANGE COM1 EXT DISPLAY COM2 EXT DISPLAY COM3 EXT DISPLAY SENSOR COM4 EXT DISPLAY...

  • Page 38: Inland Ais Specific Sentences

    Input data/Sentences Sentence (Priority) GNS>GLL>GGA>RMC VBW>RMC>VTG>OSD RMC>VTG>OSD HDT>OSD>AD-10 format ROT>Calculated value Output data/Sentences Sentence Contents AIVDM VHF data-link message AIVDO UAIS VHF data-link own-vessel report AIABK UAIS addressed and binary broadcast acknowledgement AILRF Long-range function AILR1 Long-range reply with destination for function request “A” AILR2 Long-range reply for function requests “B, C, E and F”...
  • Page 47 Y. Hatai...
  • Page 48 Mar,27'07 R.Esumi...
  • Page 49 May 20 '03...
  • Page 50 D - 7 Feb.22'05...
  • Page 51 D - 8...
  • Page 53 D-10 Feb.02'05...
  • Page 54 D-11 Nov.28'03...
  • Page 55 D-12...
  • Page 57 D-13 Y. Hatai...

  • Page 58: Interconnection Diagram

    選択 VHFアンテナ GPSアンテナ SELECT 複合空中線部 VHF ANTENNA GPS ANTENNA GPS/VHF ANTENNA GPA-017S 150M-W2VN GVA-100 FAB-151D GSC-001 150M-W2VN FAB-151D GSC-001 TNC-J-3 M-P-7 RG-10/UY TNCP-NJ NJ-TP-3DXV,1m 8D-FB-CV,30/50m *2 N-P-8DFB RG-10/UY,MAX.20m *1 M-P-3 VHF ANT 分配器 8D-FB-CV,30/50m *2 DISTRI- RG-10/UY,MAX.20m *1 BUTOR TNC-P-3 DB-1 GPS ANT TTYCS-1,MAX.100m...

This manual is also suitable for:

Fa-1501Pr-240Fa-1502Fa-150Gva-100Db-1

Table of Contents