Section 4 Schematic Diagram - Panasonic PT-VZ570 Service Manual

SECTION 4 SCHEMATIC DIAGRAM

Schematic Diagram
Model No. PT-VZ570 series
CONTENTS
SECTION 4 SCHEMATIC DIAGRAM
1. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIA-2
1.1. Power Supply Block Diagram
1.2. Signal Processing Block Diagram
1.3. System Control Block Diagram
2. Interconnection Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIA-6
3. Schematic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIA-7
3.1. A-P.C. Board (1/2)
3.2. A-P.C. Board (2/2)
3.3. A-P.C. Board
3.4. J-P.C. Board
3.5. C-P.C. Board
3.6. F-P.C. Board
3.7. L-P.C. Board
3.8. M1-P.C. Board
3.9. M2-P.C. Board
3.10. M3-P.C. Board
3.11. RC-P.C. Board
3.12. P-P.C. Board
4. Circuit Boards Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIA-12
4.1. A-P.C. Board <A side>
4.2. P-P.C. Board
4.3. C-P.C. Board
4.4. L-P.C. Board
4.5. R-P.C. Board
4.6. F-P.C. Board
4.7. J-P.C. Board
4.8. M1-P.C. Board
4.9. M2-P.C. Board
4.10. M3-P.C. Board
PT-VW530 series
PT-VX600 series
PT-VX60
Components identified by the international symbol
When replacing any of these components, use only the manufacturer's specified ones.
■ Notes
1. Resistor
All the resistors are carbon 1/4W resistors, unless marked as follows.
The unit of resistance is an OHM [Ω] (K=1 000 M=1 000000).
: Nonflammable
: Solid
: Wire Wound
2. Capacitor
: Temperature Compensation
: Polyester
: Metallized Polyester
: Polypropylene
3. Coil
The unit of inductance is a H, unless otherwise noted.
4. Test Point
: Test Point
5. HOT and COLD indications
The power circuit board contains a circuit area using a separate power supply to isolate the ground connection.
The circuit is defined by HOT and COLD indications in the schematic diagram. Take the precautions below:
6. This schematic diagram is the latest at the time of printing and the subject to change without notice.
■ Precautions
1. NEVER touch the HOT part or the HOT and COLD parts at the same time, or you may get an electric shock.
2. NEVER short-circuit the HOT and COLD circuits, or the fuse may blow and the parts may break.
3. N EVER connect an instrument such oscilloscope to the HOT and COLD circuit simultaneously, or the fuse may blow.
Connect the ground of instruments to the ground of the circuit being measured.
4. MAKE SURE to unplug the power cord from the power outlet before removing the chassis.
5. Be sure to make your orders of replacement parts according to parts list section.
DIA-1
Important Safety Notice
have special characteristics important for safety.
: Metal Oxide
: Metal Film
: Fuse
: Electrolytic
: Bipolar
: Dipped Tantalum
: Z-Type