Setting Up Rs-232 Communication - Extron electronics RCP 2000 User Manual

Operation, cont'd
Press and hold
all four buttons.
PICTURE CONTROLS
CONT
COLOR
SIZE CENTER DETAIL
TINT BRIGHT
PROGRAM
2 3 4 5 6 7 8
2 3 4 5 6 7 8
AUTO
IMAGE
PREVIEW
ION
Entering IP setup mode
2. Press the Cut or the Take button repeatedly to step
through the IP Setup menu options to access the item to be
changed.
Default
Cycle
Press simultaneously.
CONT
COLOR
SIZE
CENTER
TINT BRIGHT
Press
MAC address
IP address
CUT
A6-00-B7 I 010.056
00-0F-2B P142.008
Press
Press
CUT
CUT
Sw Baud RCP Baud
9600 9600
IP Setup menu
RCP 2000 with ISS 506 Support • Operation
3-6
Wipe an
01 = Dissolve (PIP only) 10 = S
02 = Soft Right 11 = S
H
03 = Soft Left 12 = S
04 = Soft Up 13 = S
05 = Soft Down 14 =
After 2 seconds,
06 = Soft Center In 15 =
07 = Soft Center Out 16 = the display shows
V
08 = Soft Curtain In 17 =
the MAC address.
09 = Soft Curtain Out
A6-00-B7
LOGO 1 LOGO 2
00-0F-2B
/BLACK /BLACK
ADJUST
WIPE
DISSOLVE
LOGO 1 LOGO 2
CUT TAKE
/BLACK /BLACK
The CUT button lights.
To cycle through the IP settings,
press either CUT or TAKE
.
Press the Detail button to save the
configuration and exit IP Setup.
Press Press
Switcher IP Subnet mask
CUT CUT
S010.056 S255.255
I 003.212 M255.000
Press Press
Gateway
CUT CUT
DHCP G010.056
Off M000.100
DETAIL
Press

Setting Up RS-232 Communication

CUT
3. To adjust an IP setting (RCP IP address, switcher IP
address, subnet mask, or gateway), press the appropriate
Picture Control button to select an address block (octet) to
change. The selected octet on the LCD screen blinks.
Press
Press
CONT
COLOR
BRIGHT
TINT
1st octet 2nd octet
4. Rotate the H Adjust knob to change the selected value.
Use the Picture Controls buttons
to move between address octets.
PICTURE CONTROLS
COLOR
CONT
SIZE CENTER DETAIL
TINT BRIGHT
PROGRAM
2 3 4 5 6 7 8
LOGO 1
/BLACK
2 3 4 5 6 7 8
AUTO LOGO 1
IMAGE /BLACK
PREVIEW
TION
Press the Cut or Take button
to move between IP addresses.
Adjusting the IP settings
5. When finished, press the Detail button to save the
configuration and exit IP Setup.
Once the IP addresses have been changed, if required, you can
connect to and control the RCP 2000 and the ISS 506 by using
Web pages that are resident in firmware on the RCP unit.
If you are changing your communication mode from IP to
RS-232, you may need to reconfigure the connection to the
switcher. To set up RS-232 communication,
1. Plug the supplied 12' RS-232 cable into the RCP's rear
panel To Switcher port and the switcher's RS232/422 port.
2. Press and hold the Color/Tint, Cont/Bright, Size, and
Center buttons simultaneously until the Cut button lights
and the MAC address appears in the LCD window.
RCP 2000 with ISS 506 Support • Operation
Press Press
SIZE
CENTER
3rd octet 4th octet
Use the H Adjust knob to
change the address octet.
Wipe and PIP S
01 = Dissolve (PIP only) 10 = Soft Squa
H
02 = Soft Right 11 = Soft Squa
03 = Soft Left 12 = Soft Plus
04 = Soft Up 13 = Soft Plu
05 = Soft Down 14 = Hard R
06 = Soft Center In 15 = Hard
07 = Soft Center Out 16 = Hard
V 08 = Soft Curtain In 17 = Hard D
09 = Soft Curtain Out
LOGO 2
/BLACK
ADJUST
WIPE DISOLVE
LOGO 2
CUT TAKE
/BLACK
3-7