Page 2
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben protección aislante, que puedan encontrarse dentro use. In no event will Extron Electronics be liable for direct, indirect, or consequential instalar en lugares donde no sean pisados ni apretados por objetos que se puedan de la caja o alojamiento del producto, y que puedan apoyar sobre ellos.
................A-2 Included Parts ................A-3 Accessories ...................A-3 All trademarks mentioned in this manual are the properties of their respective owners. 68-663-01 C 03 06 www.camboard.de Tel. 07131 911201 ce-info@camboard.de IR 102 Remote Control Kit • Table of Contents Fax 07131 911203...
About the IR 102 Kit Mounting the IR 102 Rx Remote Receiver Connecting the Receiver to a Switcher Features and Connections Installing Batteries in the Remote Operation www.camboard.de Tel. 07131 911201 ce-info@camboard.de IR 102 Remote Control Kit • Table of Contents Fax 07131 911203...
Page 6
Installaton and Operaton About the IR 102 Kt The Extron IR 102 Kit is an infrared (IR) remote control kit that can control a variety of Extron switchers and other devices via RS-232 or contact closure. This kit contains the following items: •...
Page 7
Align the mounting screws Mounting PMK 100 Bolt with the slots in the brackets To mount the IR 102 Rx using kit #70-374-01, do the following: Projector and place the Remote Mounting If necessary, remove feet from the bottom of the receiver.
Page 8
U-bolt for pole sizes from 1.0" to 2.5" in diameter. Secure the bracket to the U-bolt with the included hex nuts, washers, and lock washers. The IR 102 Rx can also be mounted using other kits, as shown below. Rubber Pad Rear Plate...
Page 9
+12V 1 2 3 4 5 Tx Rx RS-232/ CONTACT IR In IR 102 Rx Remote Receiver front and rear panels +12VDC Modulated IR Ground ( ) Power LED — When lit, this LED indicates power is applied. DEMOD IR Link The LED blinks during communication activity.
Page 10
— — Input #6 To select an input using the IR 102 remote control, aim the handheld unit at the IR detector and press the numeric button The cable used to connect the RS-232/Contact – Out for the desired input. For switchers with ten or more inputs, connector to a computer, control system, or contact press the +10 key to add ten to the input number selected.
Page 11
CAMBOARD Electronics Installaton and Operaton, cont’d IR 102 Remote Control Kit A ppendx A Specficatons, Part Numbers, and Accessores Specifications Included Parts Accessories www.camboard.de Tel. 07131 911201 ce-info@camboard.de 1-12 IR 102 Remote Control Kit • Installation and Operation Fax 07131 911203...
Vertrieb von CAMBOARD Electronics Specficatons, Part Numbers, and Accessores Specficatons Included Parts These items are included in each order for an IR 102 Remote Kit General (part #70-224-01): Carrier frequency ......38 kHz Included parts Replacement Max. IR range (between IR handheld remote control and IR sensor) part number 30 feet (9.1 meters)
Page 13
Specficatons, Part Numbers, and Accessores Accessores Part number VersaTools multi-product projector 70-374-01 mounting kit (PMK 300) VersaTools multi-product projector 70-563-02, -03 mounting kit (PMK 350) www.camboard.de Tel. 07131 911201 ce-info@camboard.de IR 102 Remote Control Kit • Specifications, Part #s, Accessories Fax 07131 911203...
Need help?
Do you have a question about the IR 102 and is the answer not in the manual?
Questions and answers