Page 1
Fiber Delivered Direct Diode RFL-FDDL50-100X Laser User Guide (compact module) Wuhan Raycus Fiber Laser Technologies Co., Ltd...
Page 2
WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. 1. Safety Information Thank you for choosing Raycus Fiber Delivered Direct Diode laser. This User Guide providesimportant safety, operation, warranty and other information. Please read it carefully beforeyou use this product. In order...
Page 3
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. WARNING: You must use appropriate laser safety eyewear whenoperating this device. The laser safety eyewear is selected according tothe range of wavelengths emitted from this product. The end usermust ensure that the laser safety eyewear used protects against lightemitted by the device over its entire range of wavelengths.
Page 4
Do not remove the covers of the laser, or the warranty will be voided. All maintenance mustbe performed in Raycus or by qualified Raycus personnel. 2. Product Description 2.1 Features...
Page 5
Please refer to the packing list accompanying the shipment to check actual items included. 2.3 Unpacking and Inspection Your Raycus fiber delivered direct diode laser is shipped in a package designed to providemaximum protection. Upon delivery, please inspect all packaging for evidence of mishandlingor damage. If you find any evidence of mishandling, please save the damaged material andcontact the shipping agent and Raycus immediately.
Page 6
There are no user serviceable parts, equipment or assemblies inside the product. All serviceand maintenance shall be performed by qualified Raycus personnel. In order to preventelectric shock, please do not break the seal or uncover the shield. Failure to comply withthis instruction will void the warranty;...
Page 7
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. 2.6 Specifications The specifications are listed in the following table. Table 2: Product Specifications Model *RFL-FDDL100X RFL- FDDL80X RFL- FDDL50X Max Power >600 >500 >300 Consumption (W) Power Supply 24VDC±10% Nominal Output >100...
Page 8
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 1: dimensions (unit: mm) Figure 2: Installation(unit: mm) 2.8 Installation Procedure a) Check if the power supply has the correct voltage (24VDC±10%), and the earthline is connected, make sure it is firm and reliable;...
Page 9
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. be performed byRaycus personnel or person authorized by Raycus. Make sure the environment is clean, orthe output head may be contaminated. It is prohibited to use fan during installation, whichwill cause dust in the air;...
Page 10
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 3: Front Panel View Power Cord ,USE M16 cable connector Figure 4: The Power Cord of the Laser 1:+24V ;2:GND ;3:PE Laser output Status Leds PO:power led IN:interlock led SI:signal led...
Page 11
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. TE:tempture controller alarm led RS-232 serial port, this interface is a male DB9 connector, and will be used in RS-232 mode. Control Interface,a female DB25 connector,multiple function port. 3.2 Interface Definitions 3.2.1 Control InterfaceDB25...
Page 12
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. ③ Ext_Red_Always:use with Ext_Red_EN signal,red light keeps on when these two signals are high; ④ use relay to provide normal colse piont and normal open piont of laser emmit signal and alarm signal.
Page 13
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 6: The Process of Entering Different Control Modes 3.4.1 AD Mode AD mode is a remote control mode.There are two working modes in AD Mode:CW mode and pulse mode. The output power is set by analog signal,and pulse mode is available in this control mode.
Page 14
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Figure 8: CW mode wave 3.4.1.2 Pulse mode In this mode, the laser emissionis under modulation, sosetparameters including Ext_MOD, EXT_Laser_ENand EXT_AD to switch onlaser emission.When the parameters are set, laser emission is enabled, and the remote modulation signal inputs from EXT_MOD, the laser emits.
Page 15
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Wiring in RS-232 Mode Figure 10: Wiring Diagram in RS-232 Mode There are three working modes in RS-232Mode:CW mode,modulation mode and preset mode. Six groups of laser power can be set in CW mode.
Page 16
武汉锐科光纤激光技术股份有限公司 WUHAN RAYCUS FIBER LASER TECHNOLOGIES CO. LTD. Set workign mode 00,00,0,X B7 F0 get workign mode 00,00,00,00 D7 01 F0 get workign status 00,00,00,00 B9 00 F0 Save parameter 00,00,00,01 BA F0 enable LD 00,00,00,55 BB F0 Set power in...
Page 17
The warranties start on the date of shipment from Raycus for a period of time asset forth in the applicable purchase contracts or product specifications.
Page 18
All service and maintenance shall be performed by qualified Raycuspersonnel. Please contact Raycus as soon as possible when problems under warranty aboutmaintenance happened to the product. The product returned with permission should be placed in a suitable container.
Need help?
Do you have a question about the RFL-FDDL100X and is the answer not in the manual?
Questions and answers