BRAYER BR1202 Instruction Manual page 4

6 EN
• To avoid damages, transport the unit in the original
package.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, DO NOT USE THE UNIT FOR COMMERCIAL
OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit's transportation or storage at negative
temperature, unpack it and wait for at least 3 hours
before using it.
• Unpack the unit and remove all the packaging
materials.
• Keep the original package.
• Read the safety measures and operating
recommendations.
• Check the delivery set.
• Examine the unit for damages, in case of damage do
not plug it into the mains.
• Make sure that specified specifications of power
supply voltage of the unit correspond to the
specifications of your mains. When using the unit in
the mains with 60 Hz frequency, the unit does not
need any additional settings.
• Wash the lid (7), protective lid (16) and the bottle (4)
with warm water and neutral detergent, rinse and dry.
• Wash the knife block (4) (only from the knives side)
with warm water and neutral detergent, rinse and dry.
• The cutting edges of the knife block (5) are sharp
and can be dangerous, handle the knife block (5)
carefully.
• Clean the motor unit (6) body with a soft, slightly
damp cloth, and then wipe it dry.
• Do not immerse the unit, the power cord and the
power plug into water or any other liquids.
Charging the vacuum pump (2) battery
The vacuum pump is intended for pumping the air out of
the blender bottle (4).
• To charge the battery insert the mini-USB jack into
the connector socket (8).
• Insert the USB jack into the power adapter socket
(not supplied).
• The power adapter should correspond to the
following specifications:
• Power supply: 110-240 V ~ 50/60 Hz
• Output voltage: 5V 1000 mA
• Connect the power adapter to the mains socket, the
indicator (9) will light up red. When the battery is fully
charged, the indicator (9) will light up green.
• Disconnect the power adapter from the mains,
disconnect the USB jack from the socket (8).
Preparing the vacuum lid (3)
The vacuum lid (3) is intended for longer storage of
prepared mixture in the blender bottle (4).
• Before using the vacuum lid (3) make sure that it is
clean and clean it, if necessary (see the table).
How to prepare and check the vacuum lid and the vacuum
valve.
Step 1:
Remove the assembled vacuum lid (3) from
the bottle (4) turning it counterclockwise.
Schritt 2:
Drehen Sie das Gehäuse (15) des
Vakuumventils (14) entgegen dem
Uhrzeigersinn ab.
Schritt 3:
Vergewissern Sie sich, dass sich keine
Flüssigkeitstropfen oder Fremdstoffe im
Inneren oder auf dem Vakuumventil (14)
befinden. Spülen und trocknen Sie die
Teile ab.
Schritt 4:
Setzen Sie das Vakuumventil (14)
ins Gehäuse (15) ein und drehen Sie
das Gehäuse (15) nach Gewinde im
Uhrzeigersinn zu
Schritt 5: Setzen Sie den
zusammengebauten Vakuumdeckel (3) an
der Flasche (4) an und drehen Sie diesen
nach Gewinde im Uhrzeigersinn zu.
EN
USING THE BLENDER
The blender is used for making vegetable or fruit
blends.
ATTENTION! Continuous operation time of the
blender should not exceed 1 minute, after that make
at least 5 minutes break.
Note: when using the unit for the first time, a foreign
smell from the electric motor can appear - this is normal
and it is not covered by warranty.
• Place the blender on a flat dry and steady surface.
Notes:
– the blender is not intended for crushing hard and
frozen food, chopping meat and meat products.
– the amount of the processed products should not
exceed 2/3 of the bottle (2) capacity.
– before starting to chop/mix, we recommend to peel
fruit or vegetables, remove stones, and cut fruit or
vegetables into 1х1x1 cm cubes.
Note: always add necessary amount of water or juice
into the bottle (2).
ATTENTION!
Best proportion while processing the food: 2 parts
of fruit to 3 parts of water or juice.
When making mixtures the total amount should not
exceed 600 ml.
7