Western HTS Mechanic's Manual page 29

JOYSTICK CONTROL with SECURITY GUARD™ Snowplow Anti-Theft System
SECURITY GUARD System
Activation & Establishing a 4-Digit
Security Code
NOTE: The snowplow must be
attached to the vehicle, and all the
electrical connections must be
connected prior to activating the
security code function.
1. Turn the vehicle ignition switch
to the "ON" or "ACCESSORY"
position. (It is not necessary to
start the vehicle.)
2. Verify the control power indicator
is OFF. If the power indicator
light is red, the control is ON.
Slide the ON/OFF switch to
"OFF" to turn the control OFF.
3. To activate the
SECURITY GUARD mode, move
the control lever into the #1
position four consecutive times,
and then in the direction of the
#4 position four consecutive
times (sequence:
1, 1, 1, 1, 4, 4, 4, 4). The green
FLOAT light will fl ash quickly and
the red POWER light will turn ON
indicating the system is ready to
accept your 4-digit security code.
Lit. No. 41467, Rev. 01
Enter your 4-digit security code
by moving the control lever into
the position of any of the eight
following positions: UP, DOWN,
LEFT, RIGHT, 1, 2, 3, or 4.
Once you have entered your
4-digit security code, the FLOAT
light will stop fl ashing and the
POWER light will turn OFF.
This indicates that your 4-digit
security code is entered and
stored in the SECURITY GUARD
system.
4. Once a 4-digit security code
is established and the plow/
vehicle electrical connection
are lost/disconnected, the
SECURITY GUARD system will
recognize any HTS™ control that
has been programmed with the
same 4-digit security code. Any
control not programmed with
the correct 4-digit security code
will require the user to enter the
established security code before
activating the snowplow (see the
Manual Unlock procedure).
NOTE: If the control POWER
switch is turned ON prior to
completing the programming
procedure, your 4-digit security
code will be cancelled.
Manual Unlock
If the SECURITY GUARD system is
activated and you are using a HTS™
control with a diff erent 4-digit code
than the established security code,
you will be required to manually
enter the 4-digit security code before
operating a locked snowplow.
1. Turn the vehicle ignition to the
"ON" or "ACCESSORY" position.
2. Slide the switch to turn the
control ON.
3. The POWER light will fl ash
rapidly, indicating that the
snowplow is locked.
4. Enter the 4-digit security code.
5. After entering the correct security
code, the POWER light will
change from fl ashing rapidly to a
solid light to indicate the snowplow
has been successfully unlocked.
NOTE: If the plow/vehicle electrical
connection is lost or disconnected,
the SECURITY GUARD system will
reset, requiring any HTS control
that is not programmed with
the established 4-digit security
code to have its security code
manually re-entered to activate the
snowplow.
Clearing an Established 4-Digit
Security Code
1. Turn the vehicle ignition switch
to the "ON" or "ACCESSORY"
position.
2. If the snowplow is locked (the
control POWER light will be
fl ashing at a fast rate), unlock the
snowplow by following the Manual
Unlock procedure.
3. Slide the control to the "OFF"
position. Verify that the power
indicator is OFF.
4. With the control OFF, move
the control lever to the #2
position four consecutive times,
and then to the #3 position
four consecutive times. This
sequence (2, 2, 2, 2, 3, 3, 3, 3)
will clear the 4-digit security code
from the SECURITY GUARD
system. The FLOAT light will
fl ash to indicate that the 4-digit
security code was cleared.
NOTE: To enter a new 4-digit
security code see Activation &
Establishing a 4-Digit Security
Code.
April 15, 2021
29