Western HTS Mechanic's Manual page 25

HAND-HELD CONTROL with SECURITY GUARD™ Snowplow Anti-Theft System
SECURITY GUARD System
Activation & Establishing a 4-Digit
Security Code
NOTE: The snowplow must be
attached to the vehicle, and all the
electrical connections must be
connected prior to activating the
security code function.
1. Turn the vehicle ignition switch
to the "ON" or "ACCESSORY"
position. (It is not necessary to
start the vehicle.)
2. Verify the control power indicator
is OFF. If the power indicator
light is red, the control is ON.
Press the ON/OFF button to turn
the hand-held control OFF.
3. To activate the
SECURITY GUARD mode,
press the control #1 button
four consecutive times, and
then press the #4 button four
consecutive times (sequence:
1, 1, 1, 1, 4, 4, 4, 4). The green
FLOAT light will fl ash quickly
and the red POWER light will
turn ON indicating the system
is ready to accept your 4-digit
security code. Enter your 4-digit
security code by pressing any of
the eight following buttons in any
sequence: UP, DOWN, LEFT,
RIGHT, 1, 2, 3, or 4.
Lit. No. 41467, Rev. 01
Once you have entered your
4-digit security code, the FLOAT
light will stop fl ashing and the
POWER light will turn OFF.
This indicates that your 4-digit
security code is entered and
stored in the SECURITY GUARD
system.
4. Once a 4-digit security
code is established, the
SECURITY GUARD system will
recognize any control that has
been programmed with the same
4-digit security code. If a control
not programmed with the correct
4-digit security code is connected
to the system, the established
security code will have to be
entered manually before the
snowplow can be activated (see
the Manual Unlock procedure).
NOTE: If the control POWER
button is turned ON prior to
completing the programming
procedure, your 4-digit security
code will be cancelled.
Manual Unlock
If the SECURITY GUARD system
is activated and you are using
an HTS™ control with a diff erent
4-digit code than the established
security code, you will be required
to manually enter the 4-digit security
code before operating a locked
snowplow.
1. Turn the vehicle ignition to the
"ON" or "ACCESSORY" position.
2. Turn the control ON.
3. The POWER light will fl ash
rapidly, indicating that the
snowplow is locked.
4. Enter the 4-digit security code.
5. After entering the correct security
code, the POWER light will
change from fl ashing rapidly to a
solid light to indicate the snowplow
has been successfully unlocked.
NOTE: If the plow/vehicle
electrical connection is
lost or disconnected, the
SECURITY GUARD system will
reset, requiring any HTS control
that is not programmed with
the established 4-digit security
code to have its security code
re-entered manually to activate
the snowplow.
Clearing an Established 4-Digit
Security Code
1. Turn the vehicle ignition switch
to the "ON" or "ACCESSORY"
position.
2. If the snowplow is locked (the
control POWER light will be
fl ashing at a fast rate), unlock the
snowplow by following the Manual
Unlock procedure.
3. Turn the control OFF. Verify that
the power indicator is OFF.
4. With the control OFF, press the
#2 button four consecutive times,
and then press the #3 button
four consecutive times. This
sequence (2, 2, 2, 2, 3, 3, 3, 3)
will clear the 4-digit security code
from the SECURITY GUARD
system. The FLOAT light will
fl ash to indicate that the 4-digit
security code was cleared.
NOTE: To enter a new 4-digit
security code see Activation &
Establishing a 4-Digit Security
Code.
April 15, 2021
25