Grizzly T32710 Instructions Manual

Grizzly T32710 Instructions Manual

Drill press table w/ flip-stop fence

Advertisement

Quick Links

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T32710 Drill Press Table can be
installed on your drill press for greater workpiece
support and increased accuracy.
Figure 1. Model T32710 Drill Press Table w/Flip-
Stop Fence installed on drill press.
To reduce your risk of
serious injury, read this
entire
using machine.

Specifications

Minimum Distance from Spindle to Column .. 4
Table Size ..................... 23
Fence Size .....................23
T-Slots ...........................................
Weight .......................................................12 lbs.
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
manual
BEFORE
" W x 15
" D x 1" T
3
3
4
4
" W x 1
" D x
3
1
4
4
" W x
1
2
COPYRIGHT © AUGUST, 2021 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
(FOR MODELS MFD. SINCE 08/21) #CS22038 PRINTED IN TAIWAN
DRILL PRESS TABLE w/
FLIP-STOP FENCE

Inventory

Box Contents (Figure 2)
A. Table ........................................................... 1
B. Fence.......................................................... 1
C. Flip-Stop Assemblies ................................. 2
D. Wing Knob Bolts
E. Flanged Inserts
F.
Hex Wrench 10mm ..................................... 1
A
B
If you cannot find an item on this list, care-
fully check around/inside the machine and
"
1
2
packaging materials. Often, these items get
lost in packaging materials while unpack-
" H
1
2
ing or they are pre-installed at the factory.
" H
3
8
MODEL T32710
INSTRUCTIONS
"-16 x 1" ....................... 4
3
8
"-16,
3
9
8
C
E
Figure 2. Inventory.
NOTICE
Qty
" x
" ................ 4
1
16
2
D
F
V1.08.21

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T32710 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Grizzly T32710

  • Page 1 MODEL T32710 DRILL PRESS TABLE w/ FLIP-STOP FENCE INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Inventory Box Contents (Figure 2) The Model T32710 Drill Press Table can be A. Table ............1 installed on your drill press for greater workpiece B.
  • Page 2 Model T32710 table and place table Use the following steps to install the Model upside down on workbench or table (see T32710 on your through-slot drill press table like Figure 4). the one shown in Figure 3. Figure 4. Model T32710 table ready for installation.
  • Page 3 Check if any pre-installed inserts in Model T32710 are visible through slots in drill press table (see Figure 6). A circular drill press To reduce risk of eye or face injury from table may need to be rotated. flying chips, always wear approved safety glasses and a face shield when operating a drill press or drill.
  • Page 4 File down any nicks or burrs in drill press table and clean surface. Use the following steps to install the Model T32710 on a T-slot drill press table like the ones Adjust drill press table so it is centered under shown in Figure 9.
  • Page 5 Note: Drilling these holes is a two-step Remove Model T32710 and use T-slots in drill press table to mark (4) mounting hole process. Drill first holes all the way through locations on plywood (see Figure 12). board with a diameter slightly larger than shaft of mounting screw or bolt.
  • Page 6 ⁄ "-16 x 1" knob bolts to secure Model T32710 table to plywood (see Figure 18). under plywood. 13. Line up edges of plywood with Model T32710 table and use holes drilled in Step 11 to mark Knob Bolts Plywood and drill ⁄...
  • Page 7 Lock Knobs • Periodically verify that the knob bolts used to attach the Model T32710 to the drill press table are snug. Figure 19. Location of fence lock knobs. • To avoid drilling in the table, make sure that the...
  • Page 8 Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

Table of Contents