Page 2
Caution RISK OF ELECTRIC SHOCK CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
Page 3
Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain them safely for future reference. Follow all operations and instructions accordingly.
Page 4
Important Safeguards 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, ex- treme care should be taken from touching such power lines or circuits as contact with them might be fatal.
Page 5
This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user’s own safety, and the proper operation of the product. WARNING In case of an accident, please unplug the unit from the outlet immediately. To reduce the risk of electric shock, do not remove cover or back.
Page 6
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user’s own safety, and the proper operation of the product. CAUTION Please keep the user’s manual in a safe place for future reference. Do not view the TV too close- ly since it may cause damage to your eyes.
Table of contents Installation and Maintenance Antenna Connection ........9 Video Connection .
Page 8
Supplied Accessories Make sure that the following accessories are provided with the product. AC lead Instruction manual Remote control Batteries...
Antenna Connection Indoor Antenna Connection Not recommended unless very close to the transmitter Not recommended unless very close to the transmitter. 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR : Unclear screen image and bad reception may be a cause of a wrong antenna connection.
Page 10
Antenna Connection CTV Antenna Connection Such community TV Antenna installation may be found in most of communial apartments. When a coaxial cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right. Antenna socket on the wall Antenna socket at the left side of the TV set ANT/CABLE...
Outdoor Antenna Connection An outdoor Antenna connection-such as VHF and/or UHF-may be necessary for installation in private houses. Single Antenna Connection VHF Antenna UHF Antenna Separate Antenna Connection. VHF Antenna In case of coaxial cable In case of feeder cable UHF Antenna Antenna Connection Left side of the tv set...
Video Connection Connecting with an External Source You may connect an S-Video input to enjoy clearer and brighter picture images. You can make the connection with the AV3 input. S-Video Note : If S-video and the RCA phono jacks are connected at the same time, the TV set will only detect the S-Vid- eo mode.
Watching a Camcorder Recording on TV or playing a Video Game 1. Prepare the S-video and RCA connector. 2. These connectors connect to S-video or AV 3 as shown in the picture below. 3. Turn on the TV set and camcorder/video game. 4.
DVD player connection When connecting with a component cable or Euro SCART cable Back of the tv set Note : • You can use a scart cable but some DVD’s have a component output for a better picture. • When you connect with a component video, output from your DVD player to the TV please check that the col- our of the cables between the DVD and TV set.
PC Connection When connecting with PC(D-Sub) cable. 1. First adjust resolution of the PC (640 x 480, 800 x 600, 1024 x 768, 1360 x 768(Only 100hz models), 1280 x 1024 (Only Full HD models)). 2. Then disconnect your monitor from your PC and connect between PC and TV set using the D-sub and Audio ca- ble as shown in the picture below.
Page 17
PC CONNECTION NOTES: 1) If there is a [Vertical Frequency] setting menu in the [Display] Menu of the PC, adjust the frequency to 60Hz. 2) If the PC resolution is too high, it may be hard to read letters. Select a suitable resolution. 3) HDMI input port receives only Digital Signals.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to either the Component input or SCART input AV1 or AV2. CATV Receiver Input Cable TV...
If you connect the optical output to a Dolby digital AMP, you can listen to surround sound. Dolby Digital AMP Woofer Surround L Connect with the Dolby Digital AMP. Back of the tv set Optical output Centre Surround R...
Name of Each Part Front Panel (DLT-42U1 / DLT-46U1 / DLT-42U2) The buttons on the TV set have the same functions as those of the remote control. Touch Buttons . ① Button : Each time you press this button, the TV will cycle through: TV/DVB/AV1/AV2/AV3(S-Video)/PC/HDMI 1/ HDMI 2/ Component/ TV ②...
Page 21
Front / Side Panel (DLT-42G1) The buttons on the TV set have the same functions as those of the remote control. Control Key Buttons. ① Button : Each time you press this button, the TV will cycle through: TV/DVB/AV1/AV2/AV3(S-Video)/PC/HDMI 1/ HDMI 2/ Component/ TV ②...
Page 22
Name of Each Part Side and Rear Panel Rear Panel...
(MUTE) : Press this button, and the sound goes off. MUTE POWER Press again, and the sound returns. (POWER) : TV on/off button in STANDBY mode. MULTI DVB/Analog MEDIA NORMAL 3. DVB/Analogue : Each time you press this button, the TV will toggle between DVB &...
Page 24
Parts of the Remote Controller 22. NUMBER : Press the numbers on this board, you can select pro- grammes directly in TV mode. MUTE POWER Note : When the current state is ST-BY, you can turn on the TV using the digit key. Then a PROGRAMME is selected according to MULTI DVB/Analog MEDIA...
- The basic menu appears on the screen if you press the menu button of the remote control. - There are 6 items Picture, Screen, Sound, Function, Install and DVB in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. 1.
To Watch TV On/Off, Number, Mute, Recall, / / / Buttons with same name in the main body of the TV perform the same function. Press the “ON/OFF” button on the front/side of the set or Re- mote controller • The buttons on the remote control and the main body oper- ate only when AC power is turned on.
Page 27
- If the AV1 terminal on the TV set is connected with an external device, which is switched on, the TV will come ON in AV1 mode. Otherwise, TV will come ON in RF mode. 1. Turning on the TV. •...
Setting Up TV Stations - All stations that can be received are stored by this method. It is recommended that you use Auto tuning during the installation of this set. 1. Press the “MENU” button to select the Install menu. •...
1. Press the Number buttons(0~9) or the “ PR ” but- ton to select a programme number you want. 2. Locate the selection bar on the Manual tuning at the Install menu. • Press the “MENU” button to select the Install menu. •...
Page 30
Setting Up TV Stations The Setup menu shows you information as follows: - Channel, Name, System, Sound, Fine Tuning. 1. Searching for channels in the Setup menu. • Press the “ PR “ buttons to select a program number you want. •...
Page 31
The Edit menu shows you information as follows: - Program position assignment: Program number and Station name, Real channel number. - Skip information: Red (Skip Yes), White (Skip No). 1. Deleting the program positions. • Move to Edit in the Install menu. •...
Selection of AV and Multimedia Input Signal When watching video, Camcorder, DVD, Cable TV with AV - See 12 page for connection method of TV and “Video” . - When pressing ” ” button on the TV set, screen changes as follows: AV3(S-Video) 1.
Page 33
When connecting PC, STB, DVD with Multimedia 1. Pressing the “MULTIMEDIA” button on the remote control. • The screen changes as follows: HDMI 1 HDMI 2 Component Clock 1 2 : 0 0 COMPONENT Clock 1 2 : 0 0 HDMI &...
Screen Adjustment When setting up various screen modes - The user may select various screens designed for a good picture without adjusting the brightness, contrast or col- our individually. 1. Pressing the “NORMAL” button. • The screen changes as follows: Normal Movie Dynamic...
Page 35
When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Colour, Sharpness, etc to the user’s taste. 1. Select “PICTURE” by pressing the “MENU” button. • The menu screen appears as follows. 2. Select and adjust each item. •...
Page 36
Screen Adjustment Adjustment of Screen Size in TV and AV mode - Randomly change the size of the screen. - The AUTO screen operates when power is first turned on. 1. Pressing the “ASPECT” button on the remote control. • The screen changes as follows: 16:9 14:9 Zoom 1 Zoom 2...
Page 37
Adjustment of the screen in the PC mode 1. Adjustment of the H.Position • Move to H.Position in the Screen menu. • Press the ” / ” buttons to adjust the horizontal po- sition of displayed image. 2. Adjustment of the V.Position •...
PIP & POP mode 1. PIP & POP mode when main picture is TV and AV. • Press the “P.MODE” button, then POP mode will function. • Press the “P.STILL” button, then Sub screen will freeze. • If you want to swap main for the Sub, press the “P.SWAP” button. •...
When selecting various sound modes 1. Sound mode selects what you want. • Press the “Menu” button and locate the cursor the sound mode. • Press the ” / ” button to select the sound Mode. • Sound status changes as follows : Normal News Music...
Page 40
Sound Adjustment When adjusting sound to taste - The user can enjoy various the sounds by adjusting Sound Mode, Equaliser, Virtual Dolby, Dynamic Bass and Balance 1. To adjust the audio equaliser. • Move to Equaliser in the Sound menu. •...
Page 41
Multi-Sound and Stereo 1. Mono Sound Selection • During Stereo sound reception if the stereo is weak, you can switch to MONO by pressing the “ ” button. Then the colour of “MONO” character will change to Red. In Mono reception the depth of sound is improved.
Selection of Language Selection of Language When you first turn on the TV set, the on screen display of language selection is displayed automatically. 1. Press the “MENU” button and select “Function” . 2. Select “Language” by pressing “ / ” button. 3.
Adjustment of Time - You must previously adjust current time in order to make the Automatic On/Off function to opperate. 1. Setting the Clock. • Move to Timer in the Function menu. • To go to the Clock, press the “ ” button. •...
Page 44
Adjustment of Time 4. Set up of Off Time. • Move to Timer in the Function menu. • To go to the Off Timer, press the “ / ” button. • Select Off Timer to “Yes” . • Set the Off time in the same way as above for the Clock.
1. Setup of Child Lock. • Move to Child Lock in the Function menu. • Select Child Lock to “On” using the “ / ” button. Note : • This prevents the use of the TV set without the remote control.
Teletext Analogue Teletext SWITCHING TELETEXT ON/OFF Press the “TEXT” button ( The index page or the page viewed last will appear. Press the “TEXT” button again to return to the TV mode. Note : Teletext works only in TV/AV mode. However digital broadcasts have digital text. To use digital text press the “TEXT”...
DVB Menu - Press the Menu button to display the main menu. Then, select DVB MENU. You may see the DVB MENU OSD. Whenever you need more informa- tion during any DVB MENU directory, press info button “ will see more detailed information on the screen. And in some menus, you can use the cyan, yellow, red, green buttons.
DVB menu Channel List 1. BBC ONE 2. BBC TWO 3. ITV 1 4. Channel 4 5. five 6..Select Move Function - Select the MOVE function to change the channel number and press the OK. Enter the new number you want and press the OK button. If the number you are selecting is already memorised for another channel, a warning message will appear on screen.
Page 49
Edit Favourite Lists 1. BBC ONE ① ② 2. BBC TWO ① 3. ITV 1 ② 4. Channel 4 ① ② 5. five 6..List 1 ist 2 Select List - This menu allows you to make your favourite channel list. You can make 5 favourite lists. - Move highlight on any list (1~5).
Page 50
DVB menu Select each sub-menus. Now / Next EPG - You can check now / next program here. Move highlight up/ down and get information. - Yellow/cyan button is for changing the schedule. - Press Info key “ ” to see detailed information of each pro- gram Now / Next EPG Channels...
Page 51
List Schedule EPG - You can check program schedules here. Navigate channel by pressing UP/DOWN/RIGHT/ LEFT button. - Press Yellow/cyan buttons to change date. Red/green buttons are for changing the time. - Press Info key “ ” to see detailed information of each program Electronic Programme Guide BBC ONE 1.
Page 52
DVB menu - If you want to watch a special program on time without having to use the remote everyday, please setup Timers. - At first, press select key. You will see time setup OSD. (See the right) - You can change channel at Name. - Setting start/end time as you want at Start / End.
Page 53
Select each sub-menu Configuration This has 6 sub-menus. - Change Time Zone : GMT - CET - Subtitle on/off You can also control this with the remote control SUB TITLE button. Note: You can select sub title language in the Features menu. - Change Banner time : off - 1 sec - 2sec - 4sec - 8sec - You can choose your favourite list (see page 49) in Favourite Mode.
Page 54
DVB menu Language - System : Select some language, then OSD is displayed in that language: English Spanish Danish Polish Norwegian - Preferred : has two sub menus. Audio is change the audio sound in selected language. Subtitle is change the subtitle display in selected language: English Norwegian Swedish...
Manual Search Channel Number Signal Quality: Very Good Signal Level: 0 .. 9 Select Channel Select Common Interface - This allows you to upgrade your TV set with additional features including access to extra channels (if available) using a conditional access module (eg. TopUp TV). - If there is no CI Card in the slot, „No common interface module detected”...
Troubleshooting Symptoms and Solutions Please check the following list prior to calling Daewoo Electronics Customer Service Centre for assistance. Symptom Neither picture - Check the contact of sockets is OK. nor sound - Check the TV main power is on.
Page 57
Symptom “OUT OF RANGE” appears on the screen “NO SIGNAL” ap- pears on the screen. Image is not clear. Image is not cen- tred. • AFTER SALES SERVICE Do not hesitate to contact your retailer or service agent if a change in the perfomance of your product indicates that a faulty condition may be present.
Need help?
Do you have a question about the DLT-42U1/G1HZ and is the answer not in the manual?
Questions and answers