Kubota WSM B1710 Workshop Manual page 11

B1710 · B2110 · B2410 · B2710, WSM
Model
PTO power
Maker
Model
Type
Number of cylinder
Bore and stroke
Total displacement
Engine power (ECE-R24)
Engine power
Engine
(SAE gross)
Rated revolution
Maximum torque
Battery
Starting system
Lubricating system
Cooling system
Fuel
Fuel tank
Engine crankcase
(with filter)
Capacities
Engine coolant
Transmission case
Front axle case
Front
Tires
Rear
Overall length (with 3P)
Overall width (min. tread)
Overall height
(with ROPS)
Overall height
(top of steering wheel)
Dimensions
Wheel base
Minimum ground
clearance
Front
Tread
Rear
Weight (with ROPS)
4WD with brake
Minimum turning
Bi-speed turn
radius
without brake
Clutch
Steering
Transmission
Travelling
system
Brake
Differential
Hydraulic control system
Pump capacity
Hydraulic
Three point hitch
system
At lift points
Max. lift
24 in. behind lift
force
points
PTO shaft
Rear
Revolution
PTO system
PTO shaft
Mid.
Revolution
Note : * Manufacture's estimate
The company reserves the right to change the specifications without notice.
15.0 kW (20.4 HP)*
Indirect Injection. Vertical, water-cooled, 4-cycle diesel
76 × 73.6 mm (2.99 × 2.90 in.).
1335 cm
12 V, RC : 79 min, CCA : 433 A
Electric starting with cell starter 12 V, 1.4 kW
Forced lubrication by trochoidal pump
Pressurized radiator, forced circulation with water pump
Diesel fuel No. 2-D [above −10 °C (14 °F)], Diesel fuel No. 1 [below −10 °C (14 °F]
26 L (6.9 U.S.gals., 5.7 Imp.gals.)
4.1 L (4.3 U.S.qts., 3.6 Imp.qts.)
4.5 L (4.8 U.S.qts., 4.0 Imp.qts.)
15.5 L (4.10 U.S.gals., 3.41 Imp.gals.)
5.3 L (5.6 U.S.qts., 4.7 Imp.qts.)
2625 mm (103.3 in.)
Integral type power steering
Hydrostatic transmission with 3 speeds range gear shift
3P : 24.4 L/min. (6.4 U.S.gals./min., 5.4 Imp.gals./min.)
Power steering : 11.7 L/min. (3.1 U.S.gals./min., 2.6 Imp.gals./min.)
SAE 1-3/8, 6 splines
1 speed (540 rpm at 2600 engine rpm)
USA No. 5 (KUBOTA 10-tooth) involute spline
1 speed (2500 rpm at 2578 engine rpm)
9
B2710HDB
KUBOTA
V1305-D18
4
3
(81.5 cu.in.)
18.2 kW (24.7 PS)
20.1 kW (27.0 HP)
43.3 r/s (2600 rpm)
79 N·m (59 ft-lbs)
7-12 (180 / 85D12)
12.4 -16
1365 mm (53.7 in.)
2334 mm (91.9 in.)
1375 mm (54.1 in.)
1666 mm (65.6 in.)
308 mm (12.1 in.)
935 mm (36.8 in.)
1050 mm (41.3 in.)
842 kg (1857 lbs)
2.1 m (6.9 feet)
2.1 m (6.9 feet)
Dry single plate
Wet disk type
Bevel gears
Position control
SAE Category I
830 kg (1830 lbs)
650 kg (1433 lbs)
SPECIFICATIONS
W10368160
KiSC issued 11, 2006 A