Kubota WSM B1710 Workshop Manual page 10

B1710 · B2110 · B2410 · B2710, WSM
Model
PTO power
Maker
Model
Type
Number of cylinder
Bore and stroke
Total displacement
Engine power (ECE-R24)
Engine power
Engine
(SAE gross)
Rated revolution
Maximum torque
Battery
Starting system
Lubricating system
Cooling system
Fuel
Fuel tank
Engine crankcase
(with filter)
Engine coolant
Capacities
Transmission case
Front axle case
Front
Tires
Rear
Overall length (with 3P)
Overall width (min. tread)
Overall height
(with ROPS)
Overall height
(top of steering wheel)
Dimensions
Wheel base
Minimum ground
clearance
Front
Tread
Rear
Weight (with ROPS)
4WD with brake
Minimum turning
Bi-speed turn
radius
without brake
Clutch
Steering
Transmission
Travelling
system
Brake
Differential
Hydraulic control system
Pump capacity
Hydraulic
Three point hitch
system
At lift points
Max. lift
24 in. behind lift
force
points
PTO shaft
Rear
Revolution
PTO system
PTO shaft
Mid.
Revolution
Note : * Manufacture's estimate
The company reserves the right to change the specifications without notice.
B2410D
14.3 kW (19.4 PS)*
Indirect Injection. Vertical, water-cooled, 4-cycle diesel
78 × 78.4 mm (3.07 × 3.09 in.).
1123 cm
12 V, RC : 79 min, CCA : 433 A
Electric starting with cell starter 12 V, 1.4 kW
Forced lubrication by trochoidal pump
Pressurized radiator, forced circulation with water pump
Diesel fuel No. 2-D [above −10 °C (14 °F)], Diesel fuel No. 1 [below −10 °C (14 °F]
24 L (6.3 U.S.gals., 5.3 Imp.gals.)
3.0 L (3.2 U.S.qts., 2.6 Imp.qts.)
3.8 L (4.0 U.S.qts., 3.3 Imp.qts.)
11.5 L (3.04 U.S.gals., 2.53 Imp.gals.)
3.7 L (3.9 U.S.qts.,
3.3 Imp.qts.)
810 to 1035 mm (31.9 to 40.7 in.)
692 kg (1526 lbs)
–
Integral type power steering
Gear shift, 6 forward and 2 reverse
3P : 16.6 L/min. (4.4 U.S.gals./min., 3.7 Imp.gals./min.)
Power steering : 9.8 L/min. (2.6 U.S.gals./min., 2.2 Imp.gals./min.)
1 speed (540 rpm at 2600 engine rpm)
USA No. 5 (KUBOTA 10-tooth) involute spline
1 speed (2500 rpm at 2578 engine rpm)
8
Find manuals at https://best-manuals.com Find manuals at https://best-manuals.com
B2410DB
13.4 kW (18.2 PS)*
KUBOTA
D1105-D18
3
3
(68.5 cu.in.)
15.8 kW (21.5 PS)
17.9 kW (24.0 HP)
43.3 r/s (2600 rpm)
67 N·m (49.4 ft-lbs)
4.5 L (4.8 U.S.qts., 4.0 Imp.qts.)
6.00-12
9.5-18
2430 mm (95.7 in.)
1050 mm (41.3 in.)
2298 mm (90.5 in.)
1335 mm (52.6 in.)
1500 mm (59.0 in.)
315 mm (12.4 in.)
830 mm (32.6 in.)
702 kg (1548 lbs)
2.1 m (6.9 feet)
2.1 m (6.9 feet)
Dry single plate
Wet disk type
Bevel gears
Position control
SAE Category I
750 kg (1655 lbs)
590 kg (1300 lbs)
SAE 1-3/8, 6 splines
SPECIFICATIONS
B2410HDB
12.5 L (3.30 U.S.gals.,
2.75 Imp.gals.)
718 kg (1583 lbs)
HST with 2 speeds
range gear shift
W10357020
KiSC issued 11, 2006 A