Related Manuals for RFXCOM RFXtrxLAN
Summary of Contents for RFXCOM RFXtrxLAN
- Page 1 RFXtrxLAN kit www.rfxcom.com RFXtrxLAN Rev. 2.0 page 1 / 14 Copyright, RFXCOM 2021...
-
Page 2: Table Of Contents
Table of Contents Introduction ............................3 Contents of the kit..........................3 Install the RFXtrx433XL or RFXtrx868XL in the RFXtrxLAN............4 Install the RFXtrx433E in the RFXtrxLAN..................5 Installation of the RFXtrxLAN ......................6 LAN version ............................6 6.1. -
Page 3: Introduction
1. Introduction The RFXtrxLAN can have the RFXtrx433XL or RFXtrx868XL transceiver installed. The RFXtrxLAN is not designed for the RFXtrx433E but can used if you have soldering experience. The transceiver is accessed using TCP/IP. The default settings are: TCP port 10001 and DHCP... -
Page 4: Install The Rfxtrx433Xl Or Rfxtrx868Xl In The Rfxtrxlan
Important: First thing to do is cut the PCB trace between the connection point R and the FT230X pin 15. With a PTF (PressToFit) connector in the RFXtrxLAN: Press the RFXtrx on the PTF with the antenna connector upwards. With a solder header in the RFXtrxLAN: Solder the RFXtrx on the header with the antenna connector upwards. -
Page 5: Install The Rfxtrx433E In The Rfxtrxlan
4. Install the RFXtrx433E in the RFXtrxLAN. The RFXtrxLAN is not developed to have the RFXtrx433E installed in the RFXtrxLAN in an easy way but it is possible with some solder and glue work. It is not advised for people without soldering experience. -
Page 6: Installation Of The Rfxtrxlan
Default Username / Password: admin admin Set a fixed IP address for normal use. (select DHCP OFF) or configure the RFXtrxLAN in your router. If multiple RFXtrxLAN devices are in use set the Host Name unique. Advice: If you change the Username/Password write it down on a label inside the RFXtrxLAN RFXtrxLAN Rev. -
Page 7: Configure The Serial Port
6.2. Configure the Serial Port The COM port is delivered with the correct settings. RFXtrxLAN Rev. 2.0 page 7 / 14 Copyright, RFXCOM 2021... -
Page 8: Configure The Tcp Communication
The RFXtrxLAN is delivered with the correct configured TCP Server with port 10001 You can change the Local Port and Max Accept if required. Set Max Accept to 1 unless you want to connect the RFXtrxLAN with multiple applications RFXtrxLAN Rev. 2.0... -
Page 9: Wifi Version
7. WiFi version 7.1. Configure the WiFi module For the first time you connect the RFXtrxLAN using a laptop. Power the RFXtrxLAN and connect the WiFi network with SSID HF-A11x_AP When the wireless connection is OK, open a web browser and access http://10.10.100.254... -
Page 10: Configure The Uart
7.4. Configure the UART. Select 38400,8, None, 1, Disable Set MAX TCP num to 1 unless you want to connect the RFXtrxLAN with multiple applications. 8. Restore factory settings Version without Restore button: • Make a connection for at least 3 seconds between pin 6 and 10 of the LAN controller. -
Page 11: Configure The Transceiver
9. Configure the transceiver The transceiver can be tested and configured with the RFXmngr program. Set the IP address of the RFXtrxLAN or use the Host Name. Connect port 10001: Select the protocols necessary for receive and click Set Mode followed by Save Settings. -
Page 12: Update Transceiver Firmware
Start the RFXflash program, select the IP address and select the port (normally 10001). Click the connect button: Click the Open HEX file and select the correct firmware file. RFXtrxLAN Rev. 2.0 page 12 / 14 Copyright, RFXCOM 2021... - Page 13 Click the Write device button. The firmware will be flashed in about one minute: At the end of the flash proceure click the Normal Execution Mode button: Test the RFXtrx with RFXmngr. RFXtrxLAN Rev. 2.0 page 13 / 14 Copyright, RFXCOM 2021...
-
Page 14: Warning
RFXCOM software or RFXtrx protocols or Written Materials unless expressly authorized in writing by RFXCOM. • You may not use any RFXCOM device, software or protocol as part of an exclusive or patented product without the express prior written permission of RFXCOM. •...