Advertisement
Quick Links
Advertisement
Related Manuals for Havis UT-201
Summary of Contents for Havis UT-201
- Page 1 Owner’s Manual Havis Universal Tablet Mount UT-201 www.havis.com 1-800-524-9900...
-
Page 2: Table Of Contents
Before Beginning (Original Instructions) Havis is pleased to provide this Owner’s Manual to aid in the proper installation and use of the UT-201 Universal Tablet Mount. For questions regarding the set-up of your UT-201 Universal Tablet Mount, please contact Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information. -
Page 3: Parts Included
(x2) Hardware Kit This Hardware Kit includes: 1. Zip Ties (2) 2. Integrated Zip Ties (4) 3. Pan Head Screws, M4 x 0.7 x 12mm long (5) 4. L-shaped Wrench (1) 5. Mounting Spacers(4) 6. Keys (2) www.havis.com • 1-800-524-9900... -
Page 4: Configuration
Configuration Ensure the UT-201 Universal Tablet Mount is latched by pushing inward on both Side Trays. Trays should be up against top surface as shown. Turn the UT-201 over and loosen both Side Tray Adjustment Screws and fully extend both Side Trays. - Page 5 Configuration (continued) Retighten both Side Adjustment Screws and unlatch the Side Trays by pulling out the Release Handle. Loosen both Rear Tray Adjustment Screws and fully extend the Rear Tray. (DO NOT REMOVE SCREWS) www.havis.com • 1-800-524-9900...
- Page 6 Choose the best orientation of tablet to prevent Front Fences and Side Hold-down Lugs from blocking access to crucial ports or controls. Next, place tablet onto the UT-201 and ensure it is in contact with both Front Fences and centered on the tray. Latch both Side Trays by pushing...
- Page 7 Configuration (continued) While holding tablet in position, carefully flip the UT-201 over and adjust the Rear Tray inward until the Rear Fence contacts the tablet. Ensure contact is maintained with Front Fences. Retighten Rear Tray Adjustment Screws. Torque screws to 22 in-lbs (0.25 Nm) ± 10%.
- Page 8 Configuration (continued) Carefully flip the UT-201 & tablet over and adjust the 4 Side Hold-Down Lugs vertically until firm contact is achieved with tablet. NOTE: To verify proper set-up, pull Latch Handle to ensure Side Trays release fully. If required to prevent blocking a crucial port or control, the Rear Fence can be adjusted along the length of the tablet.
-
Page 9: Installation
(Hardware Kit item #5) Align the four holes on the mounting surface with the four Mounting Holes on the bottom of the UT-201. Secure Universal Tablet Mount to the mounting surface using four Pan Head Screws (Hardware Kit Item #3) . Torque screws to 36 in-lbs (0.4 Nm) ±... -
Page 10: Cable Management
UT-201. Loop and tighten Zip Tie around wires/cables as required. Additional Strain Relief Holes have been provided on each of the four corners of the UT-201. If necessary, use these holes along with the provided Zip Ties (Hardware Kit Item #1) to strain relieve wires/cables. Loop and... -
Page 11: Operation
For theft deterrence, secure tablet by locking the Universal Tablet Mount with the supplied Key (Hardware Kit Item #6). Secure the Universal Tablet Mount by utilizing a Kensington Lock in either of the provided holes on the bottom. www.havis.com • 1-800-524-9900... - Page 12 Related Products Havis offers a wide variety of accessory products for use with the UT-201 Universal Tablet Mount. For more information or to order, please visit www.havis.com. DS-DA-218 Desktop Stand Durable stand for mounting the Universal Tablet Mount in the home or office.
Need help?
Do you have a question about the UT-201 and is the answer not in the manual?
Questions and answers