Table of Contents
Related Manuals for Miele PDR 307 EL CC
Summary of Contents for Miele PDR 307 EL CC
- Page 1 Operating and installation instructions Vented dryer Always read the operating instructions before setting up, installing and commissioning the appliance. This prevents both personal injury and damage to the machine. en-GB M.-Nr. 12 032 530...
-
Page 2: Table Of Contents
Contents Caring for the environment ................Warning and Safety instructions ..............Operating the tumble dryer ................19 Control panel ....................... 19 Symbols on the control panel ................20 Symbols in the display ..................21 Sensor controls and touch display with sensor controls ........22 Main menu...................... - Page 3 Contents 5. Starting the programme ................32 Starting the programme ..................32 6. End of programme – unloading the drum ........... 33 End of programme....................33 Unloading the drum..................... 33 Observe any maintenance notes................. 33 Programme overview ..................34 Changing the programme sequence .............. 36 Changing a programme once it has started............
- Page 4 Contents Transporting the tumble dryer to its installation site ........... 52 Installation ......................53 Levelling the tumble dryer ................53 External control equipment ................53 Electrical connection ................... 54 Installation of the ducting................. 56 General principles concerning exhaust air management ........56 General principles concerning the air supply ............
- Page 5 Drying level Machine iron ..................72 Clean the airways ....................72 Clean the filters ....................73 COM mod. selection ................... 73 Availability of Miele digital products ..............73 WiFi / LAN ......................74 Remote ........................ 75 Remote update....................75 Legal information....................76 Payment system ....................
-
Page 6: Caring For The Environment
Miele, free of charge. By law, you are solely responsible for deleting any personal data from the old appliance prior to disposal. You are legally obliged... -
Page 7: Warning And Safety Instructions
If using, do so at your own risk, and follow the in- structions provided on the packaging. Any other applications may be dangerous. Miele cannot be held liable for damage resulting from in- correct or improper use or operation. - Page 8 Warning and Safety instructions This tumble dryer may also be operated in public areas. The tumble dryer is not intended for outdoor use. This appliance can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of in- correct operation.
- Page 9 It is essential that this standard safety re- quirement is met. If in any doubt, please have the on-site wiring sys- tem inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric...
- Page 10 Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the warranty. Ensure cur- rent is not supplied to the tumble dryer until after maintenance or re- pair work has been carried out.
- Page 11 This special lamp must only be used for the purpose for which it is intended. It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised person or by Miele Service.
- Page 12 Warning and Safety instructions Correct use The maximum load for this tumble dryer is 7 kg (dry weight).The maximum recommended loads for individual programmes are given in the Programme chart. Do not lean on the door. Otherwise, the tumble dryer may tip over, causing injury to yourself or others.
- Page 13 Warning and Safety instructions The ducting must never be installed in any of the following flues or shafts. - Chimneys or smokestacks that are in use. - Shafts that are used to ventilate installation rooms with fireplaces. - Flues that are used by third parties. Smoke or exhaust gas that is fed back into the flue or shaft may be toxic.
- Page 14 Warning and Safety instructions Regularly check all components in the ducting (e.g. wall pipe, ex- ternal grille, bends, elbows, etc.) to make sure air can move through them and to ensure that they are working properly. Clean compon- ents when necessary. Fluff deposits in the ducting system will pre- vent the air from being extracted properly and, as a result, will stop the tumble dryer from working properly.
- Page 15 Warning and Safety instructions To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: - items which have not been washed. - Items, such as workwear, which have not been thoroughly cleaned and which are still soiled with grease, oil or other depos- its (such as cosmetics, lotions etc).
- Page 16 (e.g. a timer or a peak-load switch-off device). The tumble dryer may only be operated with a peak-load device if this is connected to the tumble dryer via the Miele XCI box and the relevant settings have been configured on the tumble dryer.
- Page 17 Warning and Safety instructions For tumble dryers with stainless steel surfaces: The stainless steel surfaces must not come into contact with liquid cleaning and disinfecting agents which contain chlorine or sodium hypochlorite. These agents can have a corrosive effect on stainless steel.
- Page 18 Only use genuine Miele original spare parts and accessories with this appliance. If spare parts or accessories from other manufactur- ers are used, this will invalidate the guarantee, and Miele cannot ac- cept liability. The tumble dryer can also be combined with a Miele washing ma- chine in a washer-dryer stack.
-
Page 19: Operating The Tumble Dryer
Operating the tumble dryer Control panel a Language sensor control e Optical interface For selecting the current user lan- This is used by the Service depart- guage on the display. ment as a transmission point. The operating language is displayed f Programme selector again after switching the appliance For selecting the drying programme. -
Page 20: Symbols On The Control Panel
Operating the tumble dryer Symbols on the control panel Express Normal Minimum iron Normal plus Normal Hand iron Woollens Timed drying programme Cool air Timed drying programme Warm air ... -
Page 21: Symbols In The Display
Operating the tumble dryer Symbols in the display Extras: use the Extras sensor control to add extras to a drying pro- gramme. Low temperature: the Low temperature sensor control allows you to re- duce the drying temperature. Anti-crease: the Anti-crease sensor control allows you to reduce creas- ... -
Page 22: Sensor Controls And Touch Display With Sensor Controls
Operating the tumble dryer Sensor controls and touch dis- Main menu play with sensor controls Cottons The , , and Start/Stop sensor 1:43 Normal controls and the sensor controls in the display react to finger tip contact. Every touch of a sensor control is confirmed with an audible tone. -
Page 23: Examples Of How To Operate The Appliance
Operating the tumble dryer Examples of how to operate the appliance Normal Selection list Drying level Cottons The and arrows on the right of the display indicate that choices are avail- able. After making your change, touch Setting numerical values čeština dansk ... -
Page 24: Initial Commissioning
After that, they must be changed The selected language is marked with a by Miele Service. frame and the display will change to next setting. These settings are also described under... -
Page 25: Reference To External Appliances
Initial commissioning Reference to external appli- Confirming the time request ances A reference to external hardware ap- pears. Should the time of day display not be shown? With machine switched off Touch the sensor control. connect external Information hardware, then If you select... -
Page 26: Setting Up A Payment System
cess. If you wish to change the settings Duration after the commissioning process, please contact Miele Service. Touch the sensor control in the top Touch the sensor control re- right until 0:20 appears. peatedly until the setting you require appears. -
Page 27: Notes On Correct Laundry Care
1. Notes on correct laundry care - Sew in or remove underwiring from Washing bras. - Heavily soiled laundry must be washed particularly thoroughly. Use Care label symbols sufficient detergent and select a high temperature. If in doubt, wash the Drying items several times. -
Page 28: Load The Tumble Dryer
2. Load the tumble dryer Loading the laundry Closing the door Preventing textile damage. Before loading, read chapter “1. Notes on correct laundry care.” Shut the door with a gentle swing. Open the door. Load the laundry. Preventing textile damage. -
Page 29: Selecting A Programme
* The time frame for the selected pro- out after a few minutes and/or after gramme duration can be limited by the start of a programme to save en- Miele Service. ergy. - Warm air = 0:15–2:00 hours Selecting a programme - Cool air = 0:10–2:00 hours... -
Page 30: Selecting Programme Settings
4. Selecting programme settings Low temperature Selecting extra options Delicate fabric (with the symbol on The drying programmes can be aug- the care label, e.g. acrylic garments) is mented with various extra options. dried at a lower temperature. The pro- gramme duration is also longer. -
Page 31: Selecting Delay Start
4. Selecting programme settings If the delay start time is set to Finish Selecting delay start Start at , the current times will be Delay start must be activated in the displayed. supervisor level to allow it to be selec- ... -
Page 32: Starting The Programme
5. Starting the programme Starting the programme Programme duration/Estim- ated time remaining The programme can be started as soon as the Start/Stop sensor control is The programme duration depends on flashing on and off. the quantity of laundry, the type of fab- ric and the residual moisture in the ... -
Page 33: End Of Programme - Unloading The Drum
6. End of programme – unloading the drum End of programme Unloading the drum The laundry will be cooled down shortly before the end of the programme. The laundry can now be unloaded. The programme has ended when only Finish is left on the display. -
Page 34: Programme Overview
Programme overview All weights marked with * are based on the weight of dry laundry. Express Max. load 4 kg* Use for Hardy items for the Cottons programme with the Normal drying level. Note This programme is shorter compared to the Cottons programme. Minimum iron Max. - Page 35 Programme overview Cottons Max. load 7 kg* Normal plus, Normal Use for - Single and multi-layered cotton items. - Towelling, T-shirts, underwear, jersey bed linen, baby clothes. - Workwear, jackets, cotton blankets, aprons, tea towels, bed linen, towels, table linen. Note Do not use overdry jersey fabrics (e.g.
-
Page 36: Changing The Programme Sequence
Adding laundry how the tumble dryer was set up*). Open the door. * Either during the commissioning pro- cess or subsequently, a Miele service Risk of burns by touching hot technician can reset the payment sys- laundry in the drum. -
Page 37: Cleaning And Care
Cleaning and care When to clean Always clean the appliance when this instruction appears in the display: A two-piece fluff filter in the air supply Clean the fluff filter and rinse the plinth fil- area collects all fluff generated during ter. -
Page 38: Dismantling The Fluff Filter
Cleaning and care Cleaning the fluff filter components when dry Tip: Use a vacuum cleaner to achieve the best possible cleaning results. Use the handle to pull out the fluff fil- ter. Dismantling the fluff filter Use your fingers or a vacuum cleaner to wipe fluff off the filter. -
Page 39: Cleaning The Air Supply Area
Cleaning and care Cleaning the air supply area Open the door. Fluff can be removed with a vacuum cleaner. The round lid (D) serves no purpose and cannot be removed. The fan wheel inside the tumble dryer Pull out the cover to the air supply may be clogged with detergent area. -
Page 40: Assembling And Fitting The Fluff Filter
Cleaning and care Use a damp cleaning cloth to remove any fluff. Make sure that you do not Insert the inner fluff filter component damage the rubber seal when doing into the outer component (1). this. Turn the inner section of the fluff filter Assembling and fitting the fluff filter clockwise (2) slightly until you feel it engage. -
Page 41: Cleaning The Tumble Dryer
Cleaning and care Clean the tumble dryer and the seal Close the fluff filter flap. on the inside of the door with a The filter must be inserted and the slightly damp soft cloth and a mild fluff filter flap must be closed to en- solution of washing-up liquid and wa- sure the system is correctly sealed ter. -
Page 42: Problem Solving Guide
The tumble dryer can be per- manently disabled by this safety feature. If this hap- pens, contact the Miele Customer Service Depart- ment. Finish / Cooling down This is not a fault. - Page 43 Problem solving guide Message Cause and remedy Please see “Cleaning and care” for notes on clean- Clean the filters ing. lights up after a Clean the fluff filter. specific period of time following Check and clean the air supply area. the end of a pro- ...
- Page 44 Touch the sensor control. programme has If the programme terminates again with the same er- been cancelled. ror message, then there is a fault. Contact Miele Ser- vice. The laundry is unevenly distributed or has rolled up. Obstruction detec- ...
-
Page 45: Unsatisfactory Drying Results
Problem solving guide Unsatisfactory drying results Problem Cause and remedy The laundry is not suffi- The load consisted of different types of fabric. ciently dry. Finish drying using the Timed drying warm air pro- gramme. Laundry or feather filled The laundry was washed with insufficient detergent pillows smell after dry- Feathers are a natural product and this is quite nor-... -
Page 46: The Drying Cycle Duration Is Very Long
Problem solving guide The drying cycle duration is very long Problem Cause and remedy The drying process In some circumstances, you may be asked to clean goes on too long or the air channels/filters. even switches off.* Check for all of the possible causes described be- low. -
Page 47: General Problems With The Tumble Dryer
Problem solving guide General problems with the tumble dryer Problem Cause and remedy Condensation is form- The tumble dryer is installed on a shared exhaust air ing in the drum. duct. The tumble dryer must always be installed with a non-return flap when using a shared exhaust air duct. -
Page 48: Service
In the event of any faults which you Optional accessories for this tumble cannot remedy yourself, please contact dryer are available from your Miele your Miele dealer or the Miele Customer Dealer or from the Miele Spare Parts Service Department. Department. -
Page 49: Installation
*INSTALLATION* Installation Front view a Mains connection cable e 4 height-adjustable screw feet b Control panel f Intake for air cooling c Door g On-site ducting (installed on the right or left-hand side) d Fluff filter Do not open the cover during active programme operation. -
Page 50: Rear View
*INSTALLATION* Installation Rear view a Interface for communicating with external devices b Mains connection cable c Recesses under the protruding lid for transporting the appliance d Exhaust air connections – Any exhaust air connections not in use must be sealed with a cap. -
Page 51: Locations
Side view 1131 Washer-dryer stack min. 300 1000 1702 Steel plinth A stacking kit* is required. This must be fit- ted by a Miele authorised technician. * Miele accessory available to order Steel plinth* (open or closed bases) -
Page 52: Transporting The Tumble Dryer To Its Installation Site
*INSTALLATION* Installation Transporting the tumble dryer to its Transporting the tumble dryer installation site to its installation site Danger of injury due to unsecure Damage caused by incorrect lid. transportation of the tumble dryer. The fixings at the back of the lid If the tumble dryer tips over, there is could break as a result of external a danger of injury to people and... -
Page 53: Installation
Payment systems This tumble dryer can be fitted with a payment system (optional Miele ac- cessory). In this case, a Miele Service technician must programme the relev- ant settings in the tumble dryer's elec- tronics and connect the payment sys- tem. -
Page 54: Electrical Connection
The tumble dryer may only be connec- Conversion must be performed by ted to a permanent electrical system Miele Service or by an authorised that conforms to the national and local Miele Service dealer. codes and regulations. - Page 55 *INSTALLATION* Installation This device is intended for connection to a power supply system where the maximum value of external phase neut- ral loop impedance Zmax of 0.38 Ohms at the point of distributor supply con- nection is not exceeded. The user has to ensure that this device is connected only to a power supply system which fulfils the requirement above.
-
Page 56: Installation Of The Ducting
*INSTALLATION* Installation of the ducting General principles concerning General principles concerning exhaust air management the air supply The air drawn into the appliance for Damage caused by incorrectly the drying process is extracted from installed or missing ducting. the ambient air. You must therefore Moist air from the tumble dryer can ensure that the room is sufficiently cause damage in the room where the... -
Page 57: Calculating The Total Ducting Length
*INSTALLATION* Installation of the ducting Calculating the total ducting Table I length Components Relat- The entire ducting system (including pipe bends and components) generates air length resistance that pushes against the ex- Exhaust air hose (highly flexible)* haust air. The relative pipe lengths and total ducting length have to be calcu- 1 m, laid straight 1.8 m... -
Page 58: Exhaust Air Outlets On The Back Of The Tumble Dryer
*INSTALLATION* Installation of the ducting Sample calculation Turn the cap to the left to remove it. Press the cap firmly into the open air outlet. Wall pipe, with inserted grille = 1 x 3.8 m relative pipe length = 3.8 m Dimensions of the exhaust air outlets B/D 2 bends, 90°... -
Page 59: Installing Plug-In Pipes
- A wall pipe* or a window connection* (*optional accessory) a Wall pipe (installation instructions - A plastic waste water pipe from a are provided with the Miele wall specialist retailer. If the required pipe pipe) diameter is over 100 mm, additional... -
Page 60: Installing Flexible Hoses
*INSTALLATION* Installation of the ducting Flat ducting Installing flexible hoses Use the flat ducting* to install the ex- You can install an exhaust air hose haust air hose* onto the tumble dryer if with the help of an adapter* or flat there is no space to install it to the ducting*. -
Page 61: Examples
Connection to a ventilation stack a Window connection (inserted in a pane of Perspex) a Pipe with connector b Adapter for a flexible exhaust air (= individual parts in the Miele wall pipe) hose b Adapter for a flexible exhaust air hose c Ventilation stack, moisture-proof ... -
Page 62: Consumption Data
Consumption data Final spin Resid- Energy Dura- Load size speed in tion washing ma- mois- chine ture Cottons Eco 1000 4.39 Normal 1000 2.65 Cottons Normal 1200 4.01 1400 3.80 1550 3.58 1600 3.39 Cottons Hand iron 1000 3.37 1200 3.15 1400... -
Page 63: Technical Data
Technical data Height 850 mm Width 596 mm Width (only for machines with a stain- 605 mm less steel lid) Depth 717 mm Depth with door open 1131 mm Weight 52 kg Drum volume 130 l Load size 7 kg (weight of dry laundry) Length of connection cable 2000 mm Supply voltage See data plate on back of machine... -
Page 64: Data Sheet For Household Tumble Driers
Technical data Data sheet for household tumble driers In acc. with delegated regulation (EU) No. 392/2012 MIELE Model name/identifier PDR 307 EL CC 7,0 kg Rated capacity Type of tumble drier (Air-vented / condenser) ● / - Energy efficiency class... - Page 65 Technical data If the household tumble drier is equipped with a power management system. This programme is suitable for drying normal wet cotton laundry and is the most efficient programme in terms of energy consumption for cotton. If the household tumble drier is a condenser tumble drier. For the standard cotton programme at full load.
-
Page 66: Eu Conformity Declaration
UK Conformity declaration Miele hereby declares that this vented dryer complies with UK Radio Equipment Regulations 2017, as amended. The complete text of the UK declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.co.uk... -
Page 67: Supervisor Level
Carefully enter a new code. Please inform Miele Service if you have forgotten your new code. Miele Service will have to reset the code. Make a note of your new code and... -
Page 68: Opening The Supervisor Level
Supervisor level Opening the supervisor level Touch the sensor control. The symbol appears in the display if you turn the programme selector to a programme. Access via code Supervisor Change code level The following options are available for selection: Access via code Change code... -
Page 69: Language
Supervisor level Language Finish tone volume The display can be set to appear in The volume can be changed for the one of several different languages. To audible signal that sounds at the end select the language you want, go to of the programme. -
Page 70: Fault Alarm
Supervisor level Fault alarm Further cooling The audible signal that indicates an er- Before the end of the programme, the ror can be switched off. temperature of the dried laundry is monitored and the cooling phase at - Factory default: On the end of the programme is extended if necessary. -
Page 71: Display" Switch-Off Status
Supervisor level “Display” switch-off status Programme name To save energy, the display goes out When selecting a standard pro- and the Start/Stop button flashes gramme, the name of the selected slowly. drying is shown in the display. Changing this setting leads to increased - Factory default: on energy consumption. -
Page 72: Visibility Parameters
Supervisor level Visibility parameters Clean the airways Various parameters are offered/dis- The tumble dryer's electronics calcu- played when a programme is selected. late the degree at which fluff or deter- You can decide which parameters gent residue in the fluff filters and air should not be displayed. -
Page 73: Clean The Filters
Availability of Miele digital You can adjust this reminder: Clean the products filters The ability of Miele digital products de- - Time interval of 5–55 hours pends on the availability of the services in your country. - Factory default: after 55 hours... -
Page 74: Wifi / Lan
The network remains set up; the WiFi Soft AP function is switched off. Activate the function with the Miele - Activate (visible when the network is app on your smart device within deactivated) 10 minutes. -
Page 75: Remote
- Do not switch off the tumble dryer dryer in the usual way. However, Miele during a RemoteUpdate. Otherwise, recommends installing remote updates. the RemoteUpdate will be aborted and will not be installed. -
Page 76: Legal Information
You can view information here. Copyrights and licences for operator and control software Miele uses their own and third party software which is not subject to any so- called Open Source Licence for the op- eration and control of the appliance. -
Page 77: Payment System
If you wish to change the settings after The feedback signal is sent at the the commissioning process, please end of the programme. contact Miele Service. - Release of the start button You would like to connect a payment The feedback signal is sent when the system. -
Page 78: Payment System Lock
Supervisor level Payment system lock Payment system overriding time To avoid tampering, a programme lock Setting the transition signal for the can be set up in programme opera- coin box. Security time margin to pre- tion. If the lock is applied, the pro- vent the coin box being tampered gramme is interrupted and payment with. -
Page 79: Duration Cool Air
Supervisor level Duration Cool air The running time can be adjusted. A time of between 10 and 120 minutes can be set in 5-minute increments. Factory default: 120 minutes Duration Warm air The running time can be adjusted. A time of between 20 and 120 minutes can be set in 5-minute increments. - Page 83 United Kingdom Malaysia Miele Sdn Bhd Miele Co. Ltd., Fairacres, Marcham Road Suite 12-2, Level 12 Abingdon, Oxon, OX14 1TW Menara Sapura Kencana Petroleum Professional Sales, Tel: 0845 365 6608 Solaris Dutamas No. 1, Jalan Dutamas 1 E-mail: professional@miele.co.uk 50480 Kuala Lumpur, Malaysia Internet: www.miele.co.uk/professional...
- Page 84 PDR 307 EL CC en-GB M.-Nr. 12 032 530 / 02...