Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nokia 50i
Summary of Contents for Nokia 50i
- Page 1 Nokia 50i Installation Guide Part No. N451652001 Rev A Published June 2005...
- Page 2 Rights clause at FAR 52.227-19. IMPORTANT NOTE TO USERS This software and hardware is provided by Nokia Inc. as is and any express or implied warranties, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose are disclaimed. In no event shall Nokia, or its affiliates, subsidiaries or suppliers be liable for any direct, indirect, incidental, special, exemplary, or consequential damages (including, but not limited to, procurement of substitute goods or services;...
- Page 3 #07-00 Alexandra Technopark email: info.ipnetworking_apac@nokia.com Singapore 119968 Nokia Customer Support Web Site: https://support.nokia.com/ Email: tac.support@nokia.com Americas Europe Voice: 1-888-361-5030 or Voice: +44 (0) 125-286-8900 1-613-271-6721 Fax: 1-613-271-8782 Fax: +44 (0) 125-286-5666 Asia-Pacific Voice: +65-67232999 Fax: +65-67232897 050602 Nokia 50i Installation Guide...
- Page 4 Nokia 50i Installation Guide...
-
Page 5: Table Of Contents
Overview ......... . . 17 About the Nokia 50i Gateway......17 Nokia 50i Gateway Overview . - Page 6 Index ..........57 Nokia 50i Installation Guide...
- Page 7 Figure 14 Ethernet Crossover-Cable Pin Connections ..41 Figure 15 PC Card Slots on the Nokia 50i ....44...
- Page 8 Nokia 50i Installation Guide...
- Page 9 Table 3 Pin Assignments for DB9 and DB25 Interface Cables . . 36 Table 4 System Status LEDs for the Nokia 50i ....38 Nokia 50i Installation Guide...
- Page 10 Nokia 50i Installation Guide...
-
Page 11: About This Guide
About this Guide This guide describes the installation and use of the Nokia 50i gateways. Installation and maintenance should be performed by experienced technicians or Nokia-approved service providers. This preface provides the following information: In This Guide Conventions This Guide Uses... -
Page 12: Conventions This Guide Uses
Note Notes provide information of special interest or recommendations. Command-Line Conventions This section defines the elements of commands that are available in Nokia Internet Communications products. You might encounter one or more of the following elements in a command-line path. -
Page 13: Table 1 Command-Line Conventions
The extension might be optional in certain products. ( . , ; + * - / ) Punctuation and mathematical notations are literal symbols that you must enter exactly as shown. Nokia 50i Installation Guide... -
Page 14: Text Conventions
• Emphasizes a point or denotes new terms at the Italics place where they are defined in the text. • Indicates an external book title reference. • Indicates a variable in a command: delete interface if_name Nokia 50i Installation Guide... -
Page 15: Related Documentation
In addition to this guide, documentation for this product includes the following: Nokia IP VPN Gateway Configuration Guide v6.3 describes how to configure and manage Nokia IP VPN Gateways by using the Nokia VPN Manager software. Nokia IP VPN Gateway Command-Line Summary v6.3 is a reference for the command-line interface (CLI) for Nokia IP VPN gateways. - Page 16 Nokia 50i Installation Guide...
-
Page 17: Overview
Overview This chapter provides an overview of the Nokia 50i gateway, the requirements for using the gateway. The following topics are covered: About the Nokia 50i Gateway Nokia 50i Gateway Overview Preparing the Installation Environment Site Requirements About the Nokia 50i Gateway The Nokia 50i gateway is ideally suited for growing companies and satellite offices that want high performance and security. -
Page 18: Nokia 50I Gateway Overview
Overview Nokia 50i Gateway Overview The following figures show component locations for Nokia 50i gateway. Figure 1 Component Locations Front View Status LEDs Auxiliary (AUX) port 00024 PCMCIA slots Built-in Ethernet ports Console port (10/100 Mbps) Reset switch Figure 2 Component Locations Rear View... -
Page 19: Preparing The Installation Environment
Humidity and Temperature During operation, ambient relative humidity should never exceed ninety ° ° percent and ambient air temperature must remain between 32 F and 113 ° ° C and 45 Nokia 50i Installation Guide... -
Page 20: Safety Precautions
Follow the requirements of all building and electrical codes before, during, and after installation of the gateway. Warning The gateway requires protection against short-circuits (overcurrent). Always use overcurrent protection on all conductors of electrical current to which the gateway is connected. Nokia 50i Installation Guide... - Page 21 To reduce the risk of fire, electric shock, and injury, disconnect the power cord and any cables that connect to the gateway before you open the chassis and expose internal components. Even though the power switch is turned off, power is still present inside the gateway. Nokia 50i Installation Guide...
-
Page 22: Product Disposal
Contact your local waste management agencies for specific guidelines. Site Requirements Before you install a Nokia 100i gateway, ensure that your computer room or wiring closet conforms to the environmental specifications listed in Appendix A, “Technical Specifications,”... - Page 23 Do not use the product near water. Caution Do not place objects over the ventilation holes on the Nokia 100i gateway. The components might overheat and become damaged. Caution For Nokia 100i gateway intended for shipment outside of the United States, the cord might be optional.
- Page 24 Overview Nokia 50i Installation Guide...
-
Page 25: Installing The Gateway
The Nokia 50i gateway can be rack mounted alone in a one-unit space (1U). Two Nokia 50i gateways can be rack mounted together in a 1U space by using a rack-mountable shell, which you can order separately. This section describes... -
Page 26: Figure 3 Installing The Mounting Brackets
Installing the Gateway Figure 3 Installing the Mounting Brackets Bracket position A Bracket position B 00423 Nokia 50i Installation Guide... -
Page 27: Rack Mounting Two Nokia 50I Gateways Side-By-Side
Installing the Nokia 50i Gateway The Nokia 50i gateways mount in a standard 19-inch rack with four mounting screws, as Figure 4 shows. Figure 4 Single Gateway Installation Mounting screws 00424 Rack Mounting Two Nokia 50i Gateways Side-by-Side The following procedure describes how to install two Nokia 50i gateways in a 1U rack space. -
Page 28: Figure 5 Side-By-Side Installation
2. For each gateway you are installing in the shell, use a screwdriver to rotate both locking latches on the gateway counterclockwise until the locking arms clear the sides of the shell to prevent damage during the installation. Figure 6 Locking Latches 00455 Nokia 50i Installation Guide... -
Page 29: Figure 7 Filler Panel
Installing the Nokia 50i Gateway 3. Slide one or two gateways into the shell openings. If you are installing only one gateway into the shell, cover the empty opening with a filler panel, which you secure with a single screw. -
Page 30: Figure 8 Removing The Gateway
To remove the gateway, use a screwdriver to turn the locking latch counterclockwise until you cannot turn it further with light force. Figure 8 Removing the Gateway To secure the gateway To release the gateway 00426 Nokia 50i Installation Guide... -
Page 31: Performing The Initial Configuration
Performing the Initial Configuration Performing the Initial Hardware Configuration The first time you turn on power to a Nokia 50i gateway, the initial hardware configuration process begins. This section describes how to perform the initial configuration manually by using a console connection. It includes the following sections:... - Page 32 Performing the Initial Configuration Caution Nokia recommends that you use the console cable that was delivered with your gateway for your console connection. Otherwise, ensure that the pin assignments for your cable match those provided in this section. Note Although pin assignments are the same for console and serial connections, they are used differently by the gateway.
-
Page 33: Figure 9 Console Port
If you connect the console port to a data-communications equipment device, use a straight-through cable. For cable pin assignments for the console connection, see Figure 14 page 41. 3. Connect the other end of the cable to a system running a terminal-emulation program. Nokia 50i Installation Guide... - Page 34 4. If you are using a flash memory card, insert the flash memory card into the primary flash memory card slot. The Nokia 50i has slots in the front panel for flash cards. Note Nokia recommends that you use the internal flash memory on the gateway instead of using the flash memory card.
-
Page 35: Figure 10 Pin Assignments For Console And Aux Connections
Table 3 on page 36 shows how to match pins at the console or serial connector with output pins on DB9 or DB25 cables you are using with terminal devices or other appropriate equipment. Nokia 50i Installation Guide... -
Page 36: Connecting Power And Turning The Power On
The power switch and receptacle for the power cord are located on the power supply on the back of the gateway, as shown in Figure The gateway power supply automatically detects the input voltage (120 VAC [100 to 130] or 240 VAC [200 to 264]) and configures itself appropriately. Nokia 50i Installation Guide... -
Page 37: Figure 11 Power Switch Location On The Nokia 50I
3. Press the power supply switch to the On position to provide power. Check the power LED on the front panel of the gateway (the Nokia logo) to ensure that the power supply is operating correctly. The power LED should be illuminated. -
Page 38: Figure 12 Status Led Location For The Nokia 50I
You can monitor the basic operation of the gateway and network interface cards (NICs) by checking their status LEDs. The system status LEDs are located on the front panel of the gateway. Figure 12 Status LED Location for the Nokia 50i Power or status Caution... -
Page 39: Connecting Network Interfaces
Connecting Network Interfaces Nokia 50i has four built-in dual-mode 10 Mbps and 100 Mbps ports You can connect one network interface to the network to use as the Nokia IP VPN Gateway interface. You configure this interface during the system startup procedure, which is described in the Nokia IP VPN Gateway Configuration Guide. -
Page 40: Figure 13 Output Connector For The Ethernet Cable
Figure 13 Output Connector for the Ethernet Cable Gigabit 10/100 Mbps Ethernet Pin # assignment assignment BI_DA+ 00270a BI_DA- BI_DB+ BI_DC+ BI_DC- RX - BI_DB- BI_DD+ BI_DD- Nokia 50i Installation Guide... -
Page 41: Figure 14 Ethernet Crossover-Cable Pin Connections
Connecting Network Interfaces The following figure shows the pin assignments for the RJ-45 crossover cable. Figure 14 Ethernet Crossover-Cable Pin Connections 00017.1 You can order appropriate adapter cables separately. To order additional cables, contact your cable vendor. Nokia 50i Installation Guide... - Page 42 Performing the Initial Configuration Nokia 50i Installation Guide...
-
Page 43: Installing And Replacing The Flash Memory Pc Card
You can order flash memory cards separately and use them with the Nokia 50i gateways. Each of these gateways has two PC-card slots that each support a flash memory card as small as 8 MB and as large as 64 MB. -
Page 44: Figure 15 Pc Card Slots On The Nokia 50I
Note Use the top PC slot for optimum electrostatic discharge protection. Figure 15 PC Card Slots on the Nokia 50i 00024 Slot 1 Eject buttons... -
Page 45: Troubleshooting
Problem No console connection to the gateway. Solution For information about how to create a console connection, see “Connecting the Console Port” on page 31. Nokia 50i Installation Guide... - Page 46 Problem Wrong terminal settings. Solution Verify terminal settings: 9600 bps, 8 data bits, 1 stop bit, no parity. Problem Defective gateway or file system. Solution Contact the Nokia customer support site listed in “Nokia Contact Information” on page 3. Do Not Get a Login Prompt—Error Messages Appear Problem The gateway is defective, or the file system on the gateway is defective.
- Page 47 Ethernet connection (10 Mbps, 100 Mbps, or 1000 Mbps). Problem Port not enabled. Solution Verify from the Interface page in Nokia VPN Manager that the interface port is configured as active. Problem High collision rate on the hub.
- Page 48 Troubleshooting Nokia 50i Installation Guide...
-
Page 49: A Technical Specifications
17.33 in (44.02 cm) single appliance with handles 16 in. (40.64 cm) shell only Weight Weights are for the 50i and might be less depending on which model you are installing. • 9.1 lbs. (4.1kg): Single base system with mounting brackets •... -
Page 50: Space Requirements
Technical Specifications Space Requirements Nokia 50i gateways are designed for front-screw mounting in a 19-inch rack. Each 50i gateway requires the following space in a rack: 1.60 inches (4.06 centimeters) of vertical space for a single appliance 1.71 inches (4.34 centimeters) of vertical space for appliances in a shell 16 inches (40.64 centimeters) behind the front-panel of the rack plus 6... -
Page 51: Gateway Interfaces
Gateway Interfaces Gateway Interfaces Interface Cable Type Cable Output Connector Ethernet IEEE 802.3 10BASE-T, 100BASE-TX unshielded RJ-45 twisted pair, full-duplex or half-duplex Nokia 50i Installation Guide... - Page 52 Technical Specifications Nokia 50i Installation Guide...
-
Page 53: B Compliance Information
FCC Notice (US) Declaration of Conformity According to ISO/IEC Guide 22 and EN 45014: Manufacturer’s Name: Nokia Inc. 313 Fairchild Drive Mountain View, CA 94043-2215 Manufacturer’s Address: declares that the product: Product Name: Model Number: EM5400 Product Options: Nokia 50i Installation Guide... - Page 54 Directive 89/336/EEC with Amendment 93/68/EEC. Christopher Saleem Compliance & Reliability Engineering Manager Security & Mobile Connectivity, Enterprise Solutions Mountain View, California January 2005 Elie Habib Senior Vice President Security & Mobile Connectivity, Enterprise Solutions Mountain View, CA Nokia 50i Installation Guide...
-
Page 55: Compliance Statements
EN55022 (CISPR 22 Class A) European Community (CE) Immunity Standards EN55024 European Community (CE) EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-11 Harmonics and Voltage Fluctuation EN61000-3-2 European Community (CE) EN61000-3-3 European Community (CE) Safety Standards UL60950/EN60950 US/European Community(CE) CAN/CSA-C22.2 No.60950 Canada Nokia 50i Installation Guide... -
Page 56: Fcc Notice (Us)
Consult the dealer or an experienced radio/TV technician for help. Caution Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. Nokia 50i Installation Guide... -
Page 57: Index
19 RJ-45 40, 41 temperature 19 console ventilation 19 cable connection 33 terminal settings 32 LEDs 38 data communications equipment device 33 documentation for the 50i gateway 11 modem connection, pin assignments 35 Nokia 50i Installation Guide Index - 57... - Page 58 Ethernet crossover-cable 41 power connections 36 power source, safety 21 RJ-45 connector 40, 41 safety, power source 21 specifications interfaces 51 space requirements 50 technical specifications See specifications terminal settings 32 troubleshooting 45 Index - 58 Nokia 50i Installation Guide...