Directed DS4 Plus FORD12 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. DS4 Plus FORD12
  6. Installation manual
Directed DS4 Plus FORD12 Installation Manual

Directed DS4 Plus FORD12 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
FORD12
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2017-10-12
DS4+

Advertisement

Table of Contents
loading

Related Manuals for Directed DS4 Plus FORD12

Summary of Contents for Directed DS4 Plus FORD12

  • Page 1 FORD12 Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main power harness (H1), 12-pin thick gauge connector ............... 6 Auxiliary output harness (H2), 16-pin black connector ..............6 Analog harness (H3), 18-pin white connector ................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. The siren is ONLY required when enabling the security features during module flashing. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 5: Vehicle Application Guide

    PK: Transponder & Immobilizer Override DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 6: Wiring Connections

    (MUX) Analog Input/Output H3/7 Orange/Black ISO BUS 2 H3/8 Yellow/Black ISO BUS 1 If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 7: Analog Harness (H3), 18-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)

    Lt. Green/Red (-) Parking Lights: Slide Gray or Yellow, pin 11 Parking Light Interrupt: Pin 4 DS4+ to open It is important to check that the Headlight Switch fuses are positioned correctly. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 9: Wiring Diagram - With Oem Remote Start And Without T-Harness

    (-) Parking Lights: (-) Ground: Black: 10 Gray or Yellow, Parking Light Interrupt: Pin 4 pin 11 Headlight Switch Slide DS4+ to open It is important to check that the fuses are positioned correctly. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 10: Wiring Diagram - Without Oem Remote Start And With T-Harness (Thfoc2)

    (vehicle side): Lt. Green (-) Parking Lights: Gray or Yellow, pin 11 Slide Parking Light Interrupt: Pin 4 DS4+ to open It is important to check that the Headlight Switch fuses are positioned correctly. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 11: Wiring Diagram - Without Oem Remote Start And Without T-Harness

    (-) Ground: Black: 10 (-) Parking Lights: Gray or Yellow, pin 11 Parking Light Interrupt: Pin 4 Headlight Switch Slide DS4+ to open It is important to check that the fuses are positioned correctly. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 12 Gateway module on OBDII connector. Black MS CAN High (w/ Gray/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) MS CAN Low (w/ Violet/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 13 Gateway module on OBDII connector. Black MS CAN High (w/ Gray/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) MS CAN Low (w/ Violet/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 14 Gateway module on OBDII connector. Black MS CAN High (w/ Gray/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) MS CAN Low (w/ Violet/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 15 Gateway module on OBDII connector. Black MS CAN High (w/ Gray/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) MS CAN Low (w/ Violet/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 16 Gateway module on OBDII connector. Black MS CAN High (w/ Gray Data Gateway module on OBDII connector. Black OEM Remote Start) MS CAN Low (w/ Violet Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 17 Black Gray/Red Gateway module on OBDII connector. Black Ground Black/Blue Gateway module on OBDII connector. Black HS CAN 1 High (w/o Green Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 18 Gateway module on OBDII connector. Black MS CAN High (w/ Gray/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) MS CAN Low (w/ Violet/Orange Data Gateway module on OBDII connector. Black OEM Remote Start) DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 19: Connecting The Module

    DO NOT connect the SmartStart 2-pin power harness when using the DS4+. Power and ground will be provided by the D2D connector on main module. Refer to the SmartStart documentation for further details. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 20: Optional Sensors

    SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool. Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 21: Module Programming

    3 seconds, then will turn OFF. green Note: When skipping transponder programming, the LED flashes orange, & Solid green x 3 secs then turns ON solid orange for 3 seconds, before turning OFF. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 22 By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 26. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 23: Led Diagnostics And Troubleshooting

    Flashes red x 7 connections. External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.
  • Page 24 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 25: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 26: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature using the DirectLink application for mobile devices to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ FORD12 © 2017-10-12 Directed. All rights reserved.

  • Page 27: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 28: Quick Reference Guide

    Note that the information below is for many Viper, Clifford, Python, Avital and • Directed SmartStart application via your smartphone. Automate models. Icons and commands may differ depending on the model and options purchased. Refer to your authorized installation center for more specific If applicable, you can also start the engine remotely by pressing the Lock button 3 information.
  • Page 29 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

Table of Contents